Subject: How to make Carbon fibre tubes water soluble plaster
From: Rotary Engine
Date: 2/15/2006, 6:08 AM
To: AA-me


I want to make the runners that go from the intake plenum to the
throttle body.  This requires a 180 degree sweep. Can anyone tell me
how to approach such a project.  Or recommend a good book on the
subject.     Jerry


Jerry,

My company specializes in unusual geometry for carbon fiber components.
However, we are an aerospace contractor and I can't even afford me.
The basic principals however are easy to apply to homebuilt projects.

The idea is to create a tool that "disappears" inside a locked shape.
We use various types of mandrels but the most common technique is to
make a water soluble mandrel.  There really is no limit to the shapes.

Here is a good source for the water soluble plaster.

http://www.acrtucson.com/

Another really cool technique is to make the tooling from Z-corp 3D
models and forget to reinforce the model with infiltrant.  Since,
they are bound with a water soluble material you can wash out the tool in
a bucket of
water.   We've made tube junctions and high temperature manifolds using
this
technique.   Both these methods can withstand the 14.7PSI force of a
vacuum
bag and the rigors of autoclaves.

With the 3D printer create an internal geometry that easily washes
out like a lattice work.  That saves in weight and material.

http://zcorp.com

Good luck!

-Ben

That is a new one on me Ben. I like the idea of water soluble plaster
as you can make a mold and pour the plaster in each time you need a new
tool.
In the past we have used carved styrofoam and disolved it out of the
part with acetone.

Paul Lamar


Paul,

You should've seen the Northrop Grumman quality manager when I pulled
a perfect carbon fiber plenum out of the sink.  The biggest problem
with "BIG AEROSPACE" is that they want to catalog all the tooling and
cataloging a tool that went from 3D model to water soluble part was
documenting it.
Where's the tool?  I told him it was that milk in the sink!

I think there is a potential for someone to formulate a moldable
water soluble material.  Something that a ham fist like me can shape
into a shape (play doh?) allow to harden, mold onto and wash away.

The water soluble plaster takes on the same finish as the mold in
which it was created meaning that the INSIDE of the part has a great
finish as well.
That's what we want isn't it?  I, too have washed out foam but it
left a very rough finish on the inside that's not conducive to good
airflow.

Attached are a couple of pictures of a real part done using this
technique.
We have applied for a patent on this "technology" but, I'm not real
hopeful given how mundane it is and the prior art out there.  I'm not
showing the internal structure of this tool because that's the technology
we're
struggling to protect.   The tool is about 80% air and can still hold the
forces of the bag.  God developed this a long time ago when He
designed chicken bones.  Great engineering role model.

-Ben



Paul and friends Just some FYI I talked to Acrtucson the web site that
Ben posted they have a sample pack you can purchase for $30+S&H the
woman to talk to is Halina Pender very nice lady (520) 434 6342.
Apparently they have two types they have a pour type for casting and a
more solid type for machining one is called aquacore and the other is
aquapour. Also in the sample pack is a quarte of both and a filler to
make the mold smooth and a release agent. I have a kit on the way,
it'll take about a week to get here.

Tony


Ben


What are the temps. and duration in the autoclave? I am assuming it is a
vacuums inside.

Thanks

Doug Fir.


Hi Doug,

I don't recommend autoclaving for your application.   We autoclave at 300deg
F and pressurize at 125PSI.   That's very serious composites that are
structural and highly consolidated.  We make microwave components that go
into space and they have to be super light, can't outgas and have to be
strong enough to carry several hundred dollars worth of electronics on a
Delta II ride.

My recommendation is to use a wet lay-up and a simple vacuum bag.

For something like a plenum:

3K twill weave, 3 plys (you don't need to orient them that way).
Huntsman(tm) epoxy resin for infusion (I forget the part number, I'm at
home).  Use the Freekote(tm) release on permanent tooling or a sealer on
soluble tooling (polymer of some kind from Lowe's).   Prime paint (2-part
epoxy like Polane) over the tool.   This is much lighter than gel coat and
gives you a contrasting color on the inside of the part.   I recommend white
because it shows any leaks, drips and other evidence of stuff you don't want
in your part.  The primer becomes the inside layer of your part.  Mix up a
small batch of epoxy by weight and stir in some Cab-o-sil (silica) if you
want a little more viscosity.  Paint the entire tool over the cured primer
and lay-up the 3K like you were putting on a plaster casting.  Strips work
better than big sheets.  Lay-up 3 plys the same way and have a Pepsi(tm).

At this point there are tons of options but for the vacuum bag lay-up put
your peelply over every square inch of the part (it will stick), put
breather (baby blanket) over the peel ply and bag over all that.

Suck out the air with your vacuum pump (Seal-a-meal works great) and leave
the pump on for at least 8 hours.   The Huntsman(tm) infusion resin doesn't
gel for 1:50 which is good if you're infusing since you need it to run for a
long time.   Also, it's very thin.  Silica is a good thickener but it makes
it harder to penetrate the fibers.  With a 1:50 gel time you can start over
a dozen times on a part the size of a manifold and still not have a cure
going.

Having said all that, you can use practically any resin/fiber combination
you are comfy with.  There are numerous grades of carbon fiber and even more
glass.  If you're going for a high temperature application like an intake
manifold the epoxies tend to work better than the polyesters.  We use epoxy
exclusively because all our parts fly into air or space.

I'm a strong believer in creative composite work.  This forum is good for
sharing however, there are as many ways to do something as there are members
who participate in this forum and the those who lurk here.  Try your system
on a flat piece of nylon cutting board first.   Almost nothing sticks to
them.  The idea is to get resin to kiss 360degs of each fiber.   The 3K
stands for 3,000 fibers per tow which is what you'd normally call a thread.
3K fabric is pretty light.  Getting epoxy to wet out into that is a piece of
cake.  When you look at your wet lay-up with your Pepsi in your hand you
will think it's too dry.  When you hookup the vacuum the resin will squeeze
out into the peelply and fill the breather full of excess resin.  You'll
wonder where it came from.  The result however is beautiful.

Here is a great link to a guy who, like us homebuilders, is too cheap to
spend thousands of dollars tooling up a one of a kind part.
http://www.jcrocket.com/kitchenbagging.shtml

While, I've got the floor:

I think there are other creative ways to get a shape into a composite.
We've talked about soluble tooling which is fertile ground for you geniuses
out who still remember Jr. High Chemistry class or home ec.  What are some
other materials that will become rigid yet can easily be removed?
Cardboard?  Biscuits dough?  Play Doh?  Ever consider making a rubber shape,
filling it with sand and sucking the air out of it?  Notice how rigid that
assembly is?  Ref:  coffee bags at the grocery.

What about mixing materials?  Nomex veil + Carbon + epoxy?  What resins cure
up and are able to withstand exhaust temps?  Is there anything?  What
happens when a fully cured composite is torched?  Will the carbonaceous char
still be durable enough for a pipe?

Who says you can't prefabricate a flange and glue it to a soluble tool and
glass around it?

Well, you get the picture...

-Ben



Thanks Ben,

You have peaked my interest in the material for some air ducting I plan to
do.  I am concerned like you how durable they are to fire. I have already
witness two friends who fly fiberglass birds lose them an engine fire. Nomex
veil sounds interesting.  So does ceramic mat used around the back of wood
stoves. Airplane fire wall?  Sandwich with a thin layer of stainless.?
What is the Pepsi can for?:)

Doug in Japan


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.