Subject: How to make Carbon fibre tubes water soluble plaster
From: Rotary Engine
Date: 2/16/2006, 6:06 AM
To: AA-me



    >
    > >>> I want to make the runners that go from the intake plenum to the
    > >>> throttle body. This requires a 180 degree sweep. Can anyone
   tell me
    > >>> how to approach such a project. Or recommend a good book on the
    > >>> subject. Jerry
    > >>>
    > >>>
    > >>> Jerry,
    > >>>
    > >>> My company specializes in unusual geometry for carbon fiber
   components.
    > >>> However, we are an aerospace contractor and I can't even
   afford me.
    > >>> The basic principals however are easy to apply to homebuilt
   projects.
    > >>>
    > >>> The idea is to create a tool that "disappears" inside a
   locked shape.
    > >>> We use various types of mandrels but the most common
   technique is to
    > >>> make a water soluble mandrel. There really is no limit to the
   shapes.
    > >>>
    > >>> Here is a good source for the water soluble plaster.
    > >>>
    > >>> http://www.acrtucson.com/
    > >>>
    > >>> Another really cool technique is to make the tooling from
   Z-corp 3D
    > >>> models and forget to reinforce the model with infiltrant. Since,
    > >>> they are bound with a water soluble material you can wash out
   the tool in
    > > a bucket of
    > >>> water. We've made tube junctions and high temperature
   manifolds using
    > > this
    > >>> technique. Both these methods can withstand the 14.7PSI force
   of a
    > > vacuum
    > >>> bag and the rigors of autoclaves.
    > >>>
    > >>> With the 3D printer create an internal geometry that easily
   washes
    > >>> out like a lattice work. That saves in weight and material.
    > >>>
    > >>> http://zcorp.com
    > >>>
    > >>> Good luck!
    > >>>
    > >>> -Ben
    > >>>
    > >>> That is a new one on me Ben. I like the idea of water soluble
   plaster
    > >>> as you can make a mold and pour the plaster in each time you
   need a new
    > > tool.
    > >>> In the past we have used carved styrofoam and disolved it out
   of the
    > >>> part with acetone.
    > >>>
    > >>> Paul Lamar
    > >>>
    > >>>
    > >>> Paul,
    > >>>
    > >>> You should've seen the Northrop Grumman quality manager when
   I pulled
    > >>> a perfect carbon fiber plenum out of the sink. The biggest
   problem
    > >>> with "BIG AEROSPACE" is that they want to catalog all the
   tooling and
    > >>> cataloging a tool that went from 3D model to water soluble
   part was
    > > documenting it.
    > >>> Where's the tool? I told him it was that milk in the sink!
    > >>>
    > >>> I think there is a potential for someone to formulate a moldable
    > >>> water soluble material. Something that a ham fist like me can
   shape
    > >>> into a shape (play doh?) allow to harden, mold onto and wash
   away.
    > >>>
    > >>> The water soluble plaster takes on the same finish as the mold in
    > >>> which it was created meaning that the INSIDE of the part has
   a great
    > > finish as well.
    > >>> That's what we want isn't it? I, too have washed out foam but it
    > >>> left a very rough finish on the inside that's not conducive
   to good
    > > airflow.
    > >>>
    > >>> Attached are a couple of pictures of a real part done using this
    > > technique.
    > >>> We have applied for a patent on this "technology" but, I'm
   not real
    > >>> hopeful given how mundane it is and the prior art out there.
   I'm not
    > >>> showing the internal structure of this tool because that's
   the technology
    > > we're
    > >>> struggling to protect. The tool is about 80% air and can
   still hold the
    > >>> forces of the bag. God developed this a long time ago when He
    > >>> designed chicken bones. Great engineering role model.
    > >>>
    > >>> -Ben
    > >>>
    > >>>
    > >>
    > >> Paul and friends Just some FYI I talked to Acrtucson the web
   site that
    > >> Ben posted they have a sample pack you can purchase for
   $30+S&H the
    > >> woman to talk to is Halina Pender very nice lady (520) 434 6342.
    > >> Apparently they have two types they have a pour type for
   casting and a
    > >> more solid type for machining one is called aquacore and the
   other is
    > >> aquapour. Also in the sample pack is a quarte of both and a
   filler to
    > >> make the mold smooth and a release agent. I have a kit on the way,
    > >> it'll take about a week to get here.
    > >>
    > >> Tony
    > >>
    > >
    > > Ben
    > >
    > >
    > > What are the temps. and duration in the autoclave? I am
   assuming it is a
    > > vacuums inside.
    > >
    > > Thanks
    > >
    > > Doug Fir.
    > >
    > >
    > > Hi Doug,
    > >
    > > I don't recommend autoclaving for your application. We
   autoclave at 300deg
    > > F and pressurize at 125PSI. That's very serious composites that are
    > > structural and highly consolidated. We make microwave
   components that go
    > > into space and they have to be super light, can't outgas and
   have to be
    > > strong enough to carry several hundred dollars worth of
   electronics on a
    > > Delta II ride.
    > >
    > > My recommendation is to use a wet lay-up and a simple vacuum bag.
    > >
    > > For something like a plenum:
    > >
    > > 3K twill weave, 3 plys (you don't need to orient them that way).
    > > Huntsman(tm) epoxy resin for infusion (I forget the part
   number, I'm at
    > > home). Use the Freekote(tm) release on permanent tooling or a
   sealer on
    > > soluble tooling (polymer of some kind from Lowe's). Prime paint
   (2-part
    > > epoxy like Polane) over the tool. This is much lighter than gel
   coat and
    > > gives you a contrasting color on the inside of the part. I
   recommend white
    > > because it shows any leaks, drips and other evidence of stuff
   you don't want
    > > in your part. The primer becomes the inside layer of your part.
   Mix up a
    > > small batch of epoxy by weight and stir in some Cab-o-sil
   (silica) if you
    > > want a little more viscosity. Paint the entire tool over the
   cured primer
    > > and lay-up the 3K like you were putting on a plaster casting.
   Strips work
    > > better than big sheets. Lay-up 3 plys the same way and have a
   Pepsi(tm).
    > >
    > > At this point there are tons of options but for the vacuum bag
   lay-up put
    > > your peelply over every square inch of the part (it will
   stick), put
    > > breather (baby blanket) over the peel ply and bag over all that.
    > >
    > > Suck out the air with your vacuum pump (Seal-a-meal works
   great) and leave
    > > the pump on for at least 8 hours. The Huntsman(tm) infusion
   resin doesn't
    > > gel for 1:50 which is good if you're infusing since you need it
   to run for a
    > > long time. Also, it's very thin. Silica is a good thickener but
   it makes
    > > it harder to penetrate the fibers. With a 1:50 gel time you can
   start over
    > > a dozen times on a part the size of a manifold and still not
   have a cure
    > > going.
    > >
    > > Having said all that, you can use practically any resin/fiber
   combination
    > > you are comfy with. There are numerous grades of carbon fiber
   and even more
    > > glass. If you're going for a high temperature application like
   an intake
    > > manifold the epoxies tend to work better than the polyesters.
   We use epoxy
    > > exclusively because all our parts fly into air or space.
    > >
    > > I'm a strong believer in creative composite work. This forum is
   good for
    > > sharing however, there are as many ways to do something as
   there are members
    > > who participate in this forum and the those who lurk here. Try
   your system
    > > on a flat piece of nylon cutting board first. Almost nothing
   sticks to
    > > them. The idea is to get resin to kiss 360degs of each fiber.
   The 3K
    > > stands for 3,000 fibers per tow which is what you'd normally
   call a thread.
    > > 3K fabric is pretty light. Getting epoxy to wet out into that
   is a piece of
    > > cake. When you look at your wet lay-up with your Pepsi in your
   hand you
    > > will think it's too dry. When you hookup the vacuum the resin
   will squeeze
    > > out into the peelply and fill the breather full of excess
   resin. You'll
    > > wonder where it came from. The result however is beautiful.
    > >
    > > Here is a great link to a guy who, like us homebuilders, is too
   cheap to
    > > spend thousands of dollars tooling up a one of a kind part.
    > > http://www.jcrocket.com/kitchenbagging.shtml
    > >
    > > While, I've got the floor:
    > >
    > > I think there are other creative ways to get a shape into a
   composite.
    > > We've talked about soluble tooling which is fertile ground for
   you geniuses
    > > out who still remember Jr. High Chemistry class or home ec.
   What are some
    > > other materials that will become rigid yet can easily be removed?
    > > Cardboard? Biscuits dough? Play Doh? Ever consider making a
   rubber shape,
    > > filling it with sand and sucking the air out of it? Notice how
   rigid that
    > > assembly is? Ref: coffee bags at the grocery.
    > >
    > > What about mixing materials? Nomex veil + Carbon + epoxy? What
   resins cure
    > > up and are able to withstand exhaust temps? Is there anything? What
    > > happens when a fully cured composite is torched? Will the
   carbonaceous char
    > > still be durable enough for a pipe?
    > >
    > > Who says you can't prefabricate a flange and glue it to a
   soluble tool and
    > > glass around it?
    > >
    > > Well, you get the picture...
    > >
    > > -Ben
    > >
    > >
    >
    > Thanks Ben,
    >
    > You have peaked my interest in the material for some air ducting
   I plan to
    > do. I am concerned like you how durable they are to fire. I have
   already
    > witness two friends who fly fiberglass birds lose them an engine
   fire. Nomex
    > veil sounds interesting. So does ceramic mat used around the back
   of wood
    > stoves. Airplane fire wall? Sandwich with a thin layer of stainless.?
    > What is the Pepsi can for?:)
    >
    > Doug in Japan
    >


   FYI there are lots of food savers on E-Bay cheap and all sorts and sizes
   of bagging material.

   Tony

   We used to us Fiberfrax Tm. wool years ago to plug holes in our high
   temp  (3000F) furnaces in college.  Looks just like cotton.  I
   believe it was originally manufactured by Carborundum Inc.   I did a
   quick search on the web and found this site for an update on
   materials and properties currently available.

   http://www.armilcfs.com/pages/Blankets.htm

   Joel
   Over the Hill Materials Engr.



The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.