Doug,
Great news. I found a one man brand new NC machine shop right here
in Santa Paula that has agreed to make our prototypes.
I am building two and will ship you one no charge.
I am ordering all the off the shelf parts on
Monday. You will need an electric cooling pump.
The rollers are 38 mm wide instead of 30 as that is
just what the bearings came out to. Bearings went down to
a 5/8 bore (16 mm) but bearing speed went up to
30,000 RPM.
I am still refining the design so I will keep you informed.
I will supply the 3 inch poly v belt out put pulley
and a coupling to the 2nd gen stock turbo shaft.
You will have to build a bracket to mount it on your engine.
We get this working and I will go into production :)
20 % less fuel burn on your turbo rotary.
We can then start setting long distance flight records for
lightplanes. Good PR.
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.
output pulley multi v groove
pitch dia. 3.03 inches ID 1.38" width 1 3/32 part # 1405K32 $47.42
10 grooves bushing size JA page 913
HP = tor x rpm/5151
50/12000 x 5151 = tor = 22 ft pounds = 258 inch pounds
5/8 shaft will take about 888 inch pounds
JA bushing page 898 5/8 bore 6066K11 $6.54
hardened and ground shaft 3/8 soft end 1144K19 $22.50 10 inches long page
925
-.0005 to -.001 8 to 12 micron Rc 60 to 65
hardened and ground shafts 5/8 for bearings 3" long 6061K434 $4.87 page 924
need 3
-.0005 to -.001
Bearings precision HJ 101812 Torrington bore .625 OD 1.125 30,000 RPM 3/4 inch
wide
7929K21 $10.81 shaft +.0008 to +.0017 need six page 989
spacer screws 3/8 inch head dia .781 page 2897 2.25 inch long 52.35 per 100
need 3
part number 91253A633
thrust washer 1/16 58 shaft 1 3/16 part # 7814K23 page 973 $2.57 each need
six
Paul,
Hey, That site is interesting. These people were doing what we want to do
ages ago. Just another instance of trying to find the right info. I'm
sure you checked out some of the abstracts of the papers listed. Here is
one listed under their website heading "Citations".
"The results of a test program to evaluate a compact, high performance,
fixed-ratio traction drive are presented.? This transmission, the Nasvytis
Multi-roller Traction Drive is a fixed-ratio, single-stage planetary with
two
rows of stepped planet rollers.? Two versions of the drive were
parametrically tested back-to-back at speeds to 73,000 rpm and power levels
to 180 kW (240 hp).? Parametric tests were also conducted with the Nasvytis
drive retrofitted to an automotive gas turbine engine.? The drives exhibited
good performance, with a nominal peak efficiency of 94 to 96 percent and a
maximum speed loss due to creep of approximately 3.5 percent."
Also the category under "Wave Bearing" and the different wall thickness is
something that ROTREX mentioned as well. Not new just a little different.
Good find
Doug in Japan
See I told you it was easier than it looks :)
I wish I knew about this ten years ago.
Thanks to Dale Mahan for finding this site.
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.