Subject: BMW stealing my ideas :)
From: Rotary Engine
Date: 2/25/2006, 8:50 AM
To: AA-me



   There is some engineer lurking on here working for BMW
   stealing my ideas :)

   This idea was proposed on here in March of 2005.
   That is when I first did the 3D.
   http://www.rotaryeng.net/combined-cycle-turbo-compound.jpg


   Paul Lamar ...No rotor no motor.

   Sorry Paul, but that Idea (steam bottoming cycles) has been around for
   *decades*. Extensive research was done on it funded by DOE and some
   by NSF
   in the 70's and 80's. Thermo-electron made a bottoming cycle
   over-the-road
   truck as part of the program.

   Problem was always *co$t* and complexity.

   Bill Schertz
   KIS Cruiser # 4045




http://arjournals.annualreviews.org/doi/abs/10.1146/annurev.eg.07.110182.001453;jsessionid=nzqJfRkUmYY63ZdZCM?cookieSet=1&journalCode=energy

<http://arjournals.annualreviews.org/doi/abs/10.1146/annurev.eg.07.110182.001453;jsessionid=nzqJfRkUmYY63ZdZCM?cookieSet=1&journalCode=energy>



   Oh darn :) Maybe when the price of gas hits $10 a gallon.

   BTW while I got you on the line what do you think of BMW's idea
   to use alcohol to cool the engine and let it vaporize at 173 degrees
   Fahrenheit. Doesn't the heat of vaporization require and therefore
   remove
   large amounts of heat? I would imagine the cooling system would have
   to be
   high pressure capable.

   -----------------------------------
   Oh man, where do I start.

   That is one of the most complicated bottoming cycles I have seen,
   Steam-Rankine, coupled with Organic Rankine Cycle, one primary mover
   (the
   engine), and *two* secondary engines (steam expansion and alcohol
   expansion). The control of this with varying power loads is likely
   to be a
   nightmare, coupling all the fluid flows with the heat loads and power
   requirements.

   I think someone has not thought this out very well, did some
   brainstorming
   and it is all paper study.

   Bill Schertz

   ---------------------------------
   Actally BMW have claimed to have built an engine and tested it.


   http://www.greencarcongress.com/2005/12/bmw_developing_.html
   <http://www.greencarcongress.com/2005/12/bmw_developing_.html>


   "In tests with a 1.8-liter, four-cylinder engine, the new auxiliary
   power
   unit reduced fuel consumption by up to 15% while generating nearly 14
   additional horsepower and 20 additional Nm of torque.

   The Turbosteamer is based on the same principle as the steam engine:
   heated fluid forms steam in two circuits which is used to power the
   engine.

   The primary energy supplier is the high-temperature circuit which uses
   exhaust heat from the internal combustion engine as an energy source via
   heat exchangers. More than 80% of the heat energy contained in the
   exhaust
   gases is recycled using this technology, according to BMW.

   The steam is then conducted directly into an expansion unit linked to
   the crankshaft of the internal combustion engine. Most of the remaining
   residual heat is absorbed by the cooling circuit of the engine, which
   acts as the second energy supply for the Turbosteamer."

   -------------------------------------------

   Just proves that with a computer controlling things you can
   do almost anything :)

   What about just using the alcohol to cool our rotary engines?

   --
   Paul Lamar ...No rotor no motor.

--------------------------------------------------------------------

They have to come up with a better name than "Turbosteamer".  I think my
aunt got a Turbosteamer from Ronco that she uses to clean her Showtime
Rotisserie (which she also bought from Ronco)..  :)

Matt-


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.