> I finally got time to get my failed 13b apart. The rear rotor was
> missing one apex seal, the other 2 were intact but jammed due to the
> fragments of the broken one. The rotor housing has the classic
chatter
> marks all around. Doing a Google of "13B apex seal chatter"
results in
> plenty of examples of this failure mode. Apparently the chatter
is from
> the natural resonant frequency of the seal, it eventually
fatigues the
> seal causing failure.
> The front rotor was in good shape, but the housing had the same
chatter
> marks, but not as severe as the rear rotor. The front rotor
housing was
> brand new 150 hours ago when I rebuilt this motor after the Grand
Canyon
> forced landing. At that time the good rotor housing had slight
chatter
> marks but I reused it. The front rotor was destroyed at that time
due to
> foreign object entering the rotor.
> Both rotors were missing the corner seal rubber plugs on the
side with
> the short apex seal segment. Perhaps the small segment vibrated more,
> disintegrating the rubber seals?
> The first 260 hours of flying my rotary bird was with stock 3-piece
> seals, and I never saw any chatter marks. The last 250 hours has
been
> flown with 2 piece seals and now I have chatter marks .
> I now have Tracy's 2 piece apex seals and I wonder how they will
> perform, it appears that the heavier weight of the 2 piece seals puts
> the resonant frequency in the cruising range of 6000RPM?
>
> Chuck Dunlap
> RV6 13B
>
> ----------------------------------------------------------------
>
> Couple of things Chuck. Are you mixing two cycle oil with the fuel?
> If so what kind of oil? What brand of seals did you have in there?
>
> Recently I have seen some chatter marks on Dave Leonard's engine too.
> I asked Dave what the brand of the apex seals were and he did not
tell me.
> He kind of changed the subject or he did not know. Years have
gone by and
> we have not heard of or seen chatter marks. Lately several
companies are
> claiming they are making their own apex seals.
>
>
> Seal chatter has a lot to do with the exact material they are
made from.
> Mazda uses a special cast iron alloy that is heated with
> a laser and chilled in liquid nitrogen. They would not do this
unless it
> was necessary as it is costly. I'll send some more data on this
shortly.
>
> Mazda has spent millions on seal research so I would not buy anything
> other than Mazda apex seals. Mazda have a new two piece seal
that will
> fit in your engine. Many kinds of steel alloys have been
> tried and they are known not to work including tool steel.
>
> Silicon nitride ceramic apex seals by Ianettie are known to
> work well as the density is much less than steel so too is the
weight
> This raises the resonant frequency. They are diamond ground to
> super smoothness to cut the friction which is also a factor
> in apex seal chatter.
>
> Apex seal chatter also has a lot to do with the spring
> pressure. The right springs must be used and tailored to the
> material the apex seal is made from.
>
> --------------------------------
> Here is the apex seal history.
>
> It is highly unlikley ANYONE can improve on or even equal this.
>
> Paul Lamar ...No rotor no motor.
Paul,
With a P-port engine this news gives me great concern. Should I be
looking
at ceramic Ianetti$$$$ seals? With Renesis rotors in a 13B PP
housing the
seal area will need to milled out. Decisions decisions.
Mark S. What type of seals did you use on your PP engine?
Doug in Japan
Stick with the Mazda apex seals or use the Ianetti seals.
I have Tracy's seals -- so I'm now wondering based on all this
discussion whether I am going to be having issues.
Mark Supinski
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.