Subject: Motor teardown results
From: Rotary Engine
Date: 3/16/2006, 8:19 AM
To: AAme



    I finally got time to get my failed 13b apart. The rear rotor was
    missing one apex seal, the other 2 were intact but jammed due to the
    fragments of the broken one. The rotor housing has the classic chatter
    marks all around. Doing a Google of "13B apex seal chatter" results in
    plenty of examples of this failure mode. Apparently the chatter is from
    the natural resonant frequency of the seal, it eventually fatigues the
    seal causing failure.
    The front rotor was in good shape, but the housing had the same chatter
    marks, but not as severe as the rear rotor. The front rotor housing was
    brand new 150 hours ago when I rebuilt this motor after the Grand Canyon
    forced landing. At that time the good rotor housing had slight chatter
    marks but I reused it. The front rotor was destroyed at that time
    due to
    foreign object entering the rotor.
    Both rotors were missing the  corner seal rubber plugs on the side with
    the short apex seal segment. Perhaps the small segment vibrated more,
    disintegrating the rubber seals?
    The first 260 hours of flying my rotary bird was with stock 3-piece
    seals, and I never saw any chatter marks. The last 250 hours has been
    flown with 2 piece seals and now I have chatter marks .
    I now have Tracy's 2 piece apex seals and I wonder how they will
    perform, it appears that the heavier weight of the 2 piece seals puts
    the resonant frequency in the cruising range of 6000RPM?

    Chuck Dunlap
    RV6 13B

    ----------------------------------------------------------------

    Couple of things Chuck. Are you mixing two cycle oil with the fuel?
    If so what kind of oil? What brand of seals did you have in there?

    Recently I have seen some chatter marks on Dave Leonard's engine too.
    I asked Dave what the brand of the apex seals were and he did not
    tell me.
    He kind of changed the subject or he did not know. Years have gone
    by and
    we have not heard of or seen chatter marks. Lately several companies
    are
    claiming they are making their own apex seals.


    Seal chatter has a lot to do with the exact material they are made from.
    Mazda uses a special cast iron alloy that is heated with
    a laser and chilled in liquid nitrogen. They would not do this
    unless it
    was necessary as it is costly. I'll send some more data on this shortly.

    Mazda has spent millions on seal research so I would not buy anything
    other than Mazda apex seals. Mazda  have a new two piece seal that will
    fit in your engine. Many kinds of steel alloys have been
    tried and they are known not to work including tool steel.

    Silicon nitride ceramic apex seals by Ianettie are known to
    work well as the density is much less than steel so too is the weight
    This raises the resonant frequency. They are diamond ground to
    super smoothness to cut the friction which is also a factor
    in apex seal chatter.

    Apex seal chatter also has a lot to do with the spring
    pressure. The right springs must be used and tailored to the
    material the apex seal is made from.

    Paul Lamar ...No rotor no motor.

Paul, I definitely told you what kind of seals I was using, Tracy Crooks
for the last engine, and stock 3-piece seals for the first engine.  I
have never had any problem with apex seals.  The first engine lost a side
seal, while cooling was obviously the downfall in the other.

The other thing we need to consider as a factor in the chatter is the
apex seal springs.  As you have told me, the springs tend to get weak
over time.  Weaker springs could contribute to the chatter, or even
cause it.

Chuck, did you replace the springs with your last re-build?

Dave Leonard

LCDR William Leonard
Mobile FRSS
C HSC HQ
Unit 42135
FPO AP 96426-1235

Follow the Iraq blog at:
http://leonardiniraq.blogspot.com

Turbo Rotary RV-6 N4VY
My other websites at:
http://members.aol.com/_ht_a/rotaryroster/index.html
<http://members.aol.com/_ht_a/rotaryroster/index.html>
http://members.aol.com/_ht_a/vp4skydoc/index.html

------------------------

I am really happy you are getting the newsletter in Iraq Dave.
How is it going?

Here is a picture of your rotor housing out of your last engine.
Sure looks like chatter to me :)


Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.