Subject: Herrring bone gears for traction drive.
From: Rotary Engine
Date: 3/20/2006, 2:03 PM
To: AAme




        These were a bear to draw :) First 3D jpg.

        Pratt & Whitney style herring bone with oil pressure release.
        Pratt & Whitney claims over 99 percent efficiency for the PSRU they
        made.

        These gears are 48/36 (1:33) reduction after the
        9:1 traction drive giving an over all reduction of
        12:1. At a turbine RPM of 85.000 the small pulley will
        be turning at 7083 RPM.

        The big gear has P.D of 2 inches and the small a P.D of 1.5 inches.
        each gear is a half inch wide. The herring bone arrangement cancels
        out the helical gear thrust. The gears can be reversed as can
        the multi V belt pulleys to give a range of adjustable ratios.

        The HP is anybodies guess as Boston Gear does not rate them for
        3900 FPM pitch line velocity. The formula says 56 HP but they
        talk about 1500 FPM max. They are the best Boston Gear makes
        with hardened steel and polished teeth. Hopefully they will live
        long enough to get some dyno data.

        Of course they reverse the direction of rotation making this box
        work with a stock Rx7 Turbo II engine turbo charger putting excess
        turbine
        power into the nose of the e-shaft.


        ------------------------------------------------------

        Here is what the complete box looks like with out shafts and
        traction drive
        parts. It is a check on fit and assemble. Also no helical gears as
        they take
        up considerable megabits. Yes There are  a few holes missing hear
        and there.
        I cannot imagine doing projects like this before 3D programs. For
        the guys
        designing engines in the old days it must have been a major
   undertaking.

        Second 3D jpg.

        Paul Lamar ...No rotor no motor.





   Hi Paul,

   Could you please remind me why you need the clutch(es)?


   Thanks,

   Matt-


   Well the engine has the potential HP to destroy the gear box.
   If the engine drives the gear box it would attempt to accelerate the
   turbo charger
   and the rotational inertia of the turbo charger is enormous as it is
   sped up at least ten times faster than the engine. That turbo charger
   will look like a huge flywheel to the engine and the gear box is not
   designed
   to endure those kinds of torques or loads.

   In addition to that if that were not enough the engine could in theory
   drive the turbo charger to an RPM it was not designed to sustain.

   Lets say the best overall fixed ratio is 12 to one without clutch.
   At 72,000
   RPM from the turbo charger the engine is running at 6000 RPM cruise.
   If you took off at 7500 engine RPM the turbo charger would be running
   at 90,000 RPM which may be detrimental to its health.
   The centrifugal loads on the hot turbine blades are enormous at 90,000
   RPM and above. With a waste gate we can limit the turbo charger RPM
   to something reasonable.

   Paul Lamar ...No rotor no motor.


Thanks Paul..

So the clutch will engage when the turbo wants to turn faster than the
engine (via the gear reduction)...  Any problem associated with rapid
deceleration of the engine (throttle snap closed)?  I suppose the
deceleration forces are lighter than the acceleration forces (throttle
off vs throttle on rate of change of RPM)..

How noisy is the traction drive unit?  Is it lubricated or bathed in
oil?  Does it need cooling?  Seems like the drive unit depends on the
components being springy.  How much heat is generated by flexing the
pieces?  Any resonance issues?  Will any of the clearances dramatically
change with temperature such that the mechanism won't work (not enough
traction)?


Matt-

Yes I think you have some thing there. The inertia of the prop should
slow the acceleration and deceleration.  Hopefully the belt will slip
in both case as it too has limited HP transmission capabilities. The R3350 TC had
fluid couplings which I am trying to avoid.  I have no idea so far on the noise
but helical gears are supposed to be quieter than straight cut spur gears.

Heat on flexing the ring piece is reputed to be rather high and that is why
an active cooling system is required. For the dyno model we will use
an electric pump to pump oil through the box to cool it.
I am thinking those helical gears will make a pretty good oil circulation
pump on their own.

I am sure there are resonance issues. There are always resonance issues :)
I hope to demonstrate the principle to the engine engineering world and
hopefully someone with huge resources will take over R&D. Mazda
would be the logical choice. A small all aluminum turbo compound light weight
rotary would make an excellent generator driver for a hybrid car as they
run at one RPM most of the time.

Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.