Subject: Herrring bone gears for traction drive.
From: Rotary Engine
Date: 3/21/2006, 12:55 AM
To: AAme



>
>          These were a bear to draw :) First 3D jpg.
>
>          Pratt & Whitney style herring bone with oil pressure release.
>          Pratt & Whitney claims over 99 percent efficiency for the PSRU
> they
>          made.
>
>          These gears are 48/36 (1:33) reduction after the
>          9:1 traction drive giving an over all reduction of
>          12:1. At a turbine RPM of 85.000 the small pulley will
>          be turning at 7083 RPM.
>
>          The big gear has P.D of 2 inches and the small a P.D of 1.5
> inches.
>          each gear is a half inch wide. The herring bone arrangement
> cancels
>          out the helical gear thrust. The gears can be reversed as can
>          the multi V belt pulleys to give a range of adjustable ratios.
>
>          The HP is anybodies guess as Boston Gear does not rate them for
>          3900 FPM pitch line velocity. The formula says 56 HP but they
>          talk about 1500 FPM max. They are the best Boston Gear makes
>          with hardened steel and polished teeth. Hopefully they will
live
>          long enough to get some dyno data.
>
>          Of course they reverse the direction of rotation making this
box
>          work with a stock Rx7 Turbo II engine turbo charger putting
> excess
>          turbine
>          power into the nose of the e-shaft.
>
>
>          ------------------------------------------------------
>
>          Here is what the complete box looks like with out shafts and
>          traction drive
>          parts. It is a check on fit and assemble. Also no helical gears
> as
>          they take
>          up considerable megabits. Yes There are  a few holes missing
hear
>          and there.
>          I cannot imagine doing projects like this before 3D programs.
For
>          the guys
>          designing engines in the old days it must have been a major
>     undertaking.
>
>          Second 3D jpg.
>
>          Paul Lamar ...No rotor no motor.
>
>
>
>
>
>     Hi Paul,
>
>     Could you please remind me why you need the clutch(es)?
>
>
>     Thanks,
>
>     Matt-
>
>
>     Well the engine has the potential HP to destroy the gear box.
>     If the engine drives the gear box it would attempt to accelerate the
>     turbo charger
>     and the rotational inertia of the turbo charger is enormous as it is
>     sped up at least ten times faster than the engine. That turbo
charger
>     will look like a huge flywheel to the engine and the gear box is not
>     designed
>     to endure those kinds of torques or loads.
>
>     In addition to that if that were not enough the engine could in
theory
>     drive the turbo charger to an RPM it was not designed to sustain.
>
>     Lets say the best overall fixed ratio is 12 to one without clutch.
>     At 72,000
>     RPM from the turbo charger the engine is running at 6000 RPM cruise.
>     If you took off at 7500 engine RPM the turbo charger would be
running
>     at 90,000 RPM which may be detrimental to its health.
>     The centrifugal loads on the hot turbine blades are enormous at
90,000
>     RPM and above. With a waste gate we can limit the turbo charger RPM
>     to something reasonable.
>
>     Paul Lamar ...No rotor no motor.
>
>
> Thanks Paul..
>
> So the clutch will engage when the turbo wants to turn faster than the
> engine (via the gear reduction)...  Any problem associated with rapid
> deceleration of the engine (throttle snap closed)?  I suppose the
> deceleration forces are lighter than the acceleration forces (throttle
> off vs throttle on rate of change of RPM)..
>
> How noisy is the traction drive unit?  Is it lubricated or bathed in
> oil?  Does it need cooling?  Seems like the drive unit depends on the
> components being springy.  How much heat is generated by flexing the
> pieces?  Any resonance issues?  Will any of the clearances dramatically
> change with temperature such that the mechanism won't work (not enough
> traction)?
>
>
> Matt-
>
> Yes I think you have some thing there. The inertia of the prop should
> slow the acceleration and deceleration.  Hopefully the belt will slip
> in both case as it too has limited HP transmission capabilities. The
R3350
> TC had
> fluid couplings which I am trying to avoid.  I have no idea so far on
the
> noise
> but helical gears are supposed to be quieter than straight cut spur
gears.
>
> Heat on flexing the ring piece is reputed to be rather high and that is
> why
> an active cooling system is required. For the dyno model we will use
> an electric pump to pump oil through the box to cool it.
> I am thinking those helical gears will make a pretty good oil
circulation
> pump on their own.
>
> I am sure there are resonance issues. There are always resonance issues
:)
> I hope to demonstrate the principle to the engine engineering world and
> hopefully someone with huge resources will take over R&D. Mazda
> would be the logical choice. A small all aluminum turbo compound light
> weight
> rotary would make an excellent generator driver for a hybrid car as they
> run at one RPM most of the time.
>
> Paul Lamar ...No rotor no motor.

My kid was watching CSI last night and one of the themes was street
racing,
some of which caught my eye. In particular was a scene where a
mechanic/racer is explaining to the cops how his car has a turbocharger
with
the compressor removed and the turbine puts power back into the engine via
the fan belt. Now I know this is just Hollywood but it might be
interesting
to see if there is anything to it, are the street racer doing this and how
?
I don't know anyone who seriously hot rods anymore but I bet there are a
few
in Lamar Land.

John Gibbons


That is funny! ROFL  The Hollywood types must have found our my web site
:)
"Art" imitating life. There was a guy in Western Australia doing it.


Paul Lamar ...No rotor no motor.

Herringbone gears with oil relief will not pump oil. You will need another
source of oil pressure. Would the noise of straight cut gears be heard above
the whine of the turbo and the prop tip noise?
colin smith

----------------------------------------------

We don't need a lot of pressure. They are rotating up to 10,000 RPM
so some sort of scoop would work like a centrifugal pump to catch the oil
slung off the gears. We just need to circulate the oil through a heat exchanger.

Here are some advantages of helical gears.
If you have a source for high speed straight cut gears reasonable priced
I would like to know about it. These cost me just $30 each US.

I don't know about the noise one way or the other.
-- 
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.