Paul,
You may want to rename this to: auto components for fuel or
something similar.
Maybe this is a good time to solicit opinions on the system I have
in mind that maximizes the use of modern, efficient, high
reliability auto components.
1) Dual in-tank auto fuel pump modules with integral fuel level
sensors and strainers. Use the automobile electrical connectors.
Possibly use the automobile hose connectors.
2) Fuel pressure regulation either with a conventional fuel pressure
regulator and a full flow return line or a Pulse width modulated
fuel pump speed control with a small bleed return line for air removal.
3) Fuel injection and main ignition control via a Haltech E6GMX
firing one plug per rotor. This ECU is identical to the E6X, but
has connectors to plug directly into a General Motors wiring harness
and is priced lower than the E6X. It has extra PWM outputs that can
be controlled by any of the input signals it is monitoring. It
could control a turbo wastegate and the fuel pump speed/pressure.
It has full data logging and is easy to program. Use GM ignition
coils, pressure sensors, and temperature sensors for engine control.
On the airframe use GM heater servos for flight control trim and use
auto HID headlamps for landing/taxi. A couple of salvaged GM wiring
harnesses would yield more than enough connectors for the entire
aircraft. Using a consistent set of connectors and a consistent
methodology will improve reliability.
4) Redundant ignition via a separate shaft position sensor, fixed
timing, waste spark, firing one plug per rotor. Use a simple GM
four terminal ignition module. This could be changed to a flywheel
mounted magneto if such becomes available.
5) Limp home fuel system via one or two extra injectors manually
regulated by a simple PWM control circuit. This could be made
non-electrical by using a needle valve that meters fuel into the
manifold.
I see little value to having two complete ECU systems because if one
fails, the only use for the backup is to land safely ASAP....not to
complete the mission.
Aubrey
Aubrey
Many fine point you brought up here.
#3. You might consider sourcing the connectors used in marine
applications that are waterproof by injecting a grease inside them
prior to crimping and heat shrinking.
#5. Excellent idea about the back-up extra non electrical needle
valve injectors. What is a PWM control circuit?
Doug in Japan
Doug,
A Pulse Width Modulation, or PWM, circuit consists of a square wave
generator that produces output pulses of varying duty cycle or "on
time". If a PWM circuit is used to power a lamp or a DC motor the
average power delivered to the lamp or motor would be proportional to
the percentage duty cycle of the square wave pulses. If we power a
fuel injector with the pulses then the fuel delivered would be
proportional to the percentage duty cycle of the pulses. As an
emergency fuel source, there would be a potentiometer control knob for
the pulse width circuit mounted so it could be conveniently
manipulated at the same time as the throttle. They would be adjusted
for stable engine operation at whatever power level was desired.
Aubrey
The integrated circuit part you use is called a 555 and cost about a
buck at Radio Shack. There is a dual version called a 556.
The trigger input comes from a sensor on the e-shaft and the the
variable resistor Aubrey mentioned above controls the pulse width.
There fore the amount of fuel injected is directly proportional to RPM
and the pulse width setting of the potentiometer.
This is the heart of Klaus's EFI system.
You should have no trouble keeping the engine running with this system
at a fixed throttle opening.
Paul Lamar ...No rotor no motor.
Aubrey, Paul,
Thanks. Yes I know about Pulse Width Modulation. We use the technique to
control our wind generator speed and output. Somehow the combinations of
letters didn't click in my mind. Of course BTW took me quite a while as
well. Yes the circuit is extremely simple but still requires electrical
power for the injectors.
Has anyone considered using Klaus's Lightspeed capacitor discharge system in
parallel with a Magneto mounted where the distributor or rpm Hall effect
sensor now resides?
Doug Fir
Lots of people use Klaus ignition system in conjunction with a mag on air
cooled aircraft engines.
There is no getting around some electrical on a low wing airplane unless you
rig a mechanical fuel pump. Of course you also need an electrical starter.
I just thought of something real simple and low cost. If the variable
resister controlling the 555 pulse width is mechanically connected to the
throttle it is almost a complete EFI system. You will still have to
manually lean it at altitude with another variable resister in parallel to
the one connected to the throttle.
-----------------------------------------------------
The more I think about this idea the better I like it.
Two 555's one for each rotor firing two injectors.
One linear sensor for each 555 connected to the throttle cable.
(See the 3D) The diameter of the cable drum controls the rate of change of
pot resistance with throttle movement.
For a two inch throttle cable movement and a .64 diameter drum the pot will
rotate 360 degrees. Resistance will go from zero to max.
One aux leaning pot for each 555. That way you can control the EGT or
mixture on each rotor separately. Also gives a bit of redundancy as if one
rotor EFI system craps you you still have the other.
Two Hall effect sensors on the e-shaft steel trigger plate 180 degrees
out... one for each rotor. The angular position of the Hall sensors control
when the fuel is injected.
This system is super cheap. Probably less than $100 for all the parts. Hall
sensors are less than $6 each. Pots are less than $5 each. 555's less than
$1. Then you have the injector switching transistors.
You don't need a degree in computer science or electronics to understand it
or fix it. Any mechanic should be able to build and fix it.
Probably no printed circuit board required. Can be wire wrapped or point to
point wiring used.
Paul Lamar
I seem to remember, it has been a long time since I've used one, that the
555s were not noted for pulse width stability. As a digital systems
designer, I still lean toward xtal to get the frequency resolution needed
for the pulse width resolution required. A bit more circuitry required, but
my digital rotor speed alarm system has been working in my helicopter with
zero failures for 8 yrs. Even then, if you have to sync to an outside
signal, you will get some pulse width jitter.
Stuart & Kathryn Fields, Publishers
Experimental Helo magazine
P. O. Box 1585
Inyokern, CA 93527
(760) 377-4478 ph
(760) 408-9747 publication cell
(760) 608-1299 technical cell
www.experimentalhelo.com
www.vkss.com
eh@iwvisp.com
sfkf@iwvisp.com
A little jitter won't hurt as in an EFI things average out
over time. Also I am sure improvements have been made
in 555's over the least 30 years since they were invented.
I have an original print of Don Lancaster's book
TTL Cookbook. The 555 was a favorite of Don's.
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.