Subject: Multi groove belt
From: Rotary Engine
Date: 5/1/2006, 6:55 AM
To: AAme




      >>
      >> Paul,
      >>
      >> I'm looking for a cad (dxf) profile of the V grooves for
     multi-groove
      >> belts. Is this something you have?
      >>
      >> Thanks
      >> Ken Bauman
      >>
      >> No but I have a multi V grove pulley set from McMaster Carr
      >> I will be using on the turbo compound engine.
      >> In .92 inches of width there are 10 grooves.
      >> The depth is about .090". Hard to measure exactly. I might
      >> be able to take it over to the machine shop and put it on
      >> the optical comparator if it is real important to you.
      >>
      >> This looks like a much finner pitch than the units used
      >> on the new car engines to drive the water pump and
      >> alternator. I don't have any of those lying around.
      >>
      >> When I drew it I did not take the trouble to model
      >> it exactly.
      >>
      >> Paul Lamar ...No rotor no motor.
      >
      > Machinist Handbook has them, I don't have a
      > scanner, however I might be able to take a picture
      > and send that. Not sure on the page either, but
      > I'll look it up tomorrow.
      >
      > Jarrett
      >
      > I have Mac Hinnery's hand book.
      >
      > Here it is.
      >
      > Paul Lamar ...No rotor no motor.

     Thank you

     Ken

     Ken, I think this is the web site you are looking for.

     -------------------------

     I take it back. That Gates web site sucks. Who ever heard
     of having to register before you can download a pdf catalog.
     The on line catalog is ridiculous as well. Sometimes these
     people shoot them selves in the foot.

     Here is a better one.

     http://www.cptbelts.com/products/vribbed/vee_rib/index.html

     You want a 3D DXF or a 2D DXF ?

     Paul Lamar ...No rotor no motor.

     ------------------------------------------------

     Paul,

     Hutchinson is a good source of info for Poly V belts:
     http://www.hutchinsontransmission.com/

     They will mail you a design manual on request, which includes
detailed
     tech info and a calculator for sizing.


     Regards,

     Gordon.


     Thanks Gordon. I bought some cast iron pulleys from Mac Master but
     I am not happy with them. The three inch pulley weighs 1.5 pounds
     with QD bushing and has an RPM limit of 8340. The 4.5 " large one
     weighs 2.75 pounds and has an RPM limit of 5560 making it marginal
     for this application. See the chart for the design point. I think
     I could do better if I found some steel sheet metal pulleys as found
on
     most automotive engines these days. These are J section pulleys and
     most automotive engines use the L section belts I suspect.
     The L section however looks marginal as far as RPM is concerned for
     the stock RX8 engine with a red line of 9,000 RPM.
     This chart is probably rather conservative.

     Paul Lamar ...No rotor no motor.


     Paul,

     If you go to the Hutchinson link I gave and click on "contacts" you
can
     request the design manual and a list of distributors for pulleys. I
     think both aluminum and steel are available and should go to 10,000
rpm.

     The PJ section belt has a rib pitch of 2.34mm [.092"] and thickness
     of 3.5mm [.138"], which sounds about right.

     Incidentally, the design manual lists "ultralight aircraft" as one of
     the application categories and I know Simonini 2-stroke UL engines
use
     these belts, so no worries about having to fib about what you intend
to
     use it for.

     Regards,

     Gordon.

     Thanks again Gordon. What is interesting about these
     belts is they are not really V-belts at all. There is no
     wedging action going on. They are basically folded
     up, guided flat belts with much more effective width than
     a regular flat belt. The HP transmission capabilities are
     stunning. What is old is new again :)

     Paul Lamar


Paul,

Yeah these belts are really cool technology -- there is no wedging, just
friction. Some of the bigger ones are rated at over 1000hp, will take
high duty cycles, high rpm etc. and will last very long.

They also have great efficiency, 95 to 98 percent, which is as good or
better than cog belts, which wear out quickly. I really like these for a
prop reduction drive and I'm sure they will start catching on once
people clue into them.

Regards,

Gordon.



I know of one controlled descent (much slipping) to a rough landing because
the poly v reduction didn't like flying in the rain shower. Some water
deflecting cover would be necessary for long-term comfort.

Colin Smith

Are you talking about a Robinson helicoptor Colin?  If so poly v
and V Ribbed are entirly different animals. However that is not to
say V Ribbed would not also be affected by lots of water.

Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.