I just thought of something real simple and low
cost. If the variable
resister controlling the 555 pulse width is
mechanically connected to
the throttle it is almost a complete EFI system.
You will still have
to manually lean it at altitude with another
variable resister
in parallel to the one connected to the throttle.
-----------------------------------------------------
The more I think about this idea the better I like
it.
Two 555's one for each rotor firing two injectors.
One linear sensor for each 555 connected to the
throttle cable.
(See the 3D) The diameter of the cable drum controls
the
rate of change of pot resistance with throttle
movement.
For a two inch throttle cable movement and a .64
diameter
drum the pot will rotate 360 degrees. Resistance
will
go from zero to max.
One aux leaning pot for each 555. That way you can
control
the EGT or mixture on each rotor separately. Also
gives a bit
of redundancy as if one rotor EFI system craps out
you still
have the other.
Two Hall effect sensors on the e-shaft .065" thick
CR steel trigger
plate 180 degrees out... one for each rotor. The
angular position
of the Hall sensors control when the fuel is
injected.
This system is super cheap. Probably less than $100
for
all the parts. Hall sensors are less than $6 each.
Pots
are less than $5 each. 555's less than $1. Then you
have
the injector switching transistors.
You don't need a degree in computer science or
electronics
to understand it or fix it. Any mechanic should be
able to
build and fix it.
Probably no printed circuit board required. Can be
wire
wrapped or point to point wiring.
--------------------------------------------------------
This is the fundamental reason why this system is
simpler
and cheaper than a micro computer based system.
A $300 CPU system takes in one or two pulses from an
$30 to $70
expensive inductive sensor on the e-shaft wheel,
calculates
the RPM, decides when to fire the ignition, decides
when
to inject the fuel, and decides how wide of a pulse
the fuel
injector needs.
If you can accept fixed timing (all air cooled
aircraft engines
have fixed timing) with both plugs firing
at the same time TWO $7 Hall effect sensors sensing
TWO teeth on one E-shaft sensor wheel can fire the
integrated
ignition coils. Done! Finished! So much for the
ignition.
If you use TWO more Hall effect sensors and TWO more
teeth
on ANOTHER e-shaft sensor wheel they can fire two $1
555 8 pin
integrated circuit which in turn send out a variable
width pulse to the injectors. That takes care of the
injector
pulse timing. Almost done. How does one control the
width
of the pulse the 555 sends to the injector? Simple!
Use TWO $5
variable resistors that sense throttle position.
These are the $7 Hall effect vane sensors to use.
http://catalog.sensing.honeywell.com/datasheet.asp?PN=4AV20F%2DT2&FAM=solidstate&P=2292
They are good to 125 C or 257 F. Klaus uses Hall
effect sensors
for his ignition system and EFI system not expensive
inductive
sensors.
BTW some might say throttle position is not what you
want.
Intake manifold pressure sensing is what you want.
True but intake
manifold pressure sensing is harder and more
expensive to implement.
Not impossible as Klaus's 555 based system does it.
On the other hand this throttle position sensor
system is set
to start and run super rich. Fine for starting and
climb out.
When you get to cruise altitude you fine tune
the mixture just like an air cooled aircraft engine.
Also BTW note it is simple to adapt this system to a
three rotor.
Just replicate everything one more time.
This system is close to a 75% mechanical fuel
injection system.
Paul Lamar ...No rotor no motor.
Paul
As you have commented before, the devil is in the
details. So, I must point out that most rotary
potentiometers move thru an arc of about 300 degrees,
and you must not link them to a mechanism capable of
rotating them against their internal stops. Breakage
is eminent. In addition 2 separate pots can not be
expected to track each other closely, but thats ok if
you plan to trim them independently. And don't be
tempted to use a consumer grade linear pot, they are
not sealed and very prone to getting contaminated. I
also would suggest not using 2 separate 555 ic's where
you want them tracking. Instead use a 556 dual, then
you get the inherent matching of monolithic circuitry.
regards, Robert
I put that out there to see if anybody was paying attention :)
You get an A in the classs :)
Yes. Just reduce the diameter of the drum by the ratio
of 300/360. So as the throttle moves 2 inches the
pot rotates 300 degrees. Wire wound pots are still
less than $10 each. Also the throttle pots are just behind the
instrument panel so the environment is not all
that bad.
Good point on the 556.
----------------------------------------------------
ops that should have been:
Just INCREASE the diameter of the drum by the ratio
of 360/300.
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.