>>
>> I just thought of something real simple and low
>> cost. If the variable
>> resister controlling the 555 pulse width is
>> mechanically connected to
>> the throttle it is almost a complete EFI system. You will still
have
>> to manually lean it at altitude with another
>> variable resister
>> in parallel to the one connected to the throttle.
>>
>>
> -----------------------------------------------------
>
>>
>> The more I think about this idea the better I like
>> it.
>>
>> Two 555's one for each rotor firing two injectors.
>>
>> One linear sensor for each 555 connected to the
>> throttle cable.
>> (See the 3D) The diameter of the cable drum controls
>> the
>> rate of change of pot resistance with throttle
>> movement.
>> For a two inch throttle cable movement and a .64
>> diameter
>> drum the pot will rotate 360 degrees. Resistance
>> will
>> go from zero to max.
>>
>> One aux leaning pot for each 555. That way you can
>> control
>> the EGT or mixture on each rotor separately. Also
>> gives a bit
>> of redundancy as if one rotor EFI system craps out
>> you still
>> have the other.
>>
>> Two Hall effect sensors on the e-shaft .065" thick
>> CR steel trigger
>> plate 180 degrees out... one for each rotor. The
>> angular position
>> of the Hall sensors control when the fuel is
>> injected.
>>
>> This system is super cheap. Probably less than $100
>> for
>> all the parts. Hall sensors are less than $6 each.
>> Pots
>> are less than $5 each. 555's less than $1. Then you
>> have
>> the injector switching transistors.
>>
>> You don't need a degree in computer science or
>> electronics
>> to understand it or fix it. Any mechanic should be
>> able to
>> build and fix it.
>>
>> Probably no printed circuit board required. Can be
>> wire
>> wrapped or point to point wiring.
>>
>>
> --------------------------------------------------------
>
>>
>> This is the fundamental reason why this system is
>> simpler
>> and cheaper than a micro computer based system.
>> A $300 CPU system takes in one or two pulses from an
>> $30 to $70
>> expensive inductive sensor on the e-shaft wheel,
>> calculates
>> the RPM, decides when to fire the ignition, decides
>> when
>> to inject the fuel, and decides how wide of a pulse
>> the fuel
>> injector needs.
>>
>> If you can accept fixed timing (all air cooled
>> aircraft engines
>> have fixed timing) with both plugs firing
>> at the same time TWO $7 Hall effect sensors sensing
>> TWO teeth on one E-shaft sensor wheel can fire the
>> integrated
>> ignition coils. Done! Finished! So much for the
>> ignition.
>>
>> If you use TWO more Hall effect sensors and TWO more
>> teeth
>> on ANOTHER e-shaft sensor wheel they can fire two $1
>> 555 8 pin
>> integrated circuit which in turn send out a variable
>> width pulse to the injectors. That takes care of the
>> injector
>> pulse timing. Almost done. How does one control the
>> width
>> of the pulse the 555 sends to the injector? Simple!
>> Use TWO $5
>> variable resistors that sense throttle position.
>>
>> These are the $7 Hall effect vane sensors to use.
>>
>
http://catalog.sensing.honeywell.com/datasheet.asp?PN=4AV20F%2DT2&FAM=solidstate&P=2292
<http://catalog.sensing.honeywell.com/datasheet.asp?PN=4AV20F%2DT2&FAM=solidstate&P=2292>
<
http://catalog.sensing.honeywell.com/datasheet.asp?PN=4AV20F%2DT2&FAM=solidstate&P=2292
<http://catalog.sensing.honeywell.com/datasheet.asp?PN=4AV20F%2DT2&FAM=solidstate&P=2292>>
>
>
>> They are good to 125 C or 257 F. Klaus uses Hall
>> effect sensors
>> for his ignition system and EFI system not expensive
>> inductive
>> sensors.
>>
>> BTW some might say throttle position is not what you
>> want.
>> Intake manifold pressure sensing is what you want.
>> True but intake
>> manifold pressure sensing is harder and more
>> expensive to implement.
>> Not impossible as Klaus's 555 based system does it.
>>
>> On the other hand this throttle position sensor
>> system is set
>> to start and run super rich. Fine for starting and
>> climb out.
>> When you get to cruise altitude you fine tune
>> the mixture just like an air cooled aircraft engine.
>>
>> Also BTW note it is simple to adapt this system to a
>> three rotor.
>> Just replicate everything one more time.
>>
>> This system is close to a 75% mechanical fuel
>> injection system.
>>
>> Paul Lamar ...No rotor no motor.
>
>
>
> Paul
>
> As you have commented before, the devil is in the
> details. So, I must point out that most rotary
> potentiometers move thru an arc of about 300 degrees,
> and you must not link them to a mechanism capable of
> rotating them against their internal stops. Breakage
> is eminent. In addition 2 separate pots can not be
> expected to track each other closely, but thats ok if
> you plan to trim them independently. And don't be
> tempted to use a consumer grade linear pot, they are
> not sealed and very prone to getting contaminated. I
> also would suggest not using 2 separate 555 ic's where
> you want them tracking. Instead use a 556 dual, then
> you get the inherent matching of monolithic circuitry.
>
> regards, Robert
>
> I put that out there to see if anybody was paying attention :)
> You get an A in the classs :)
>
> Yes. Just reduce the diameter of the drum by the ratio
> of 300/360. So as the throttle moves 2 inches the
> pot rotates 300 degrees. Wire wound pots are still
> less than $10 each. Also the throttle pots are just behind the
> instrument panel so the environment is not all
> that bad.
>
> Good point on the 556.
>
> ----------------------------------------------------
> ops that should have been:
>
> Just INCREASE the diameter of the drum by the ratio
> of 360/300.
>
> Paul Lamar ...No rotor no motor.
I have actually built an electronic fuel injection system. It
is a lot
more complicated than this.
You have to change the duty cycle with manifold pressure. The
engine
won't run unless you do this, at least in a simple fashion.
You have to change the duty cycle with RPM. Again, the engine
won't run
unless you do this at least in a simple fashion.
The throttle position alone isn't enough to set the duty cycle.
The
engine won't run.
In theory, you could sense the intake air mass flow and set the
duty
cycle based on that alone. (Manifold pressure and RPM together
allow you
to estimate mass flow.)
I think you would be better off with a hand-controlled needle
valve than
you would be with a 555 based EFI.
Bill Dube'
--------------------------------------------------------
Was it a rotary engine?
I have some rotary engine experience on the dyno with Tracy's
EFI system and the rotary engine will run over a very wide ratio
of fuel to air mixture. Anything from 8:1 of air to fuel to
18:1 air
to fuel according to the wide band fuel/air ratio sensor and
display.
Piston engines stumble long before 18:1.
It uses only intake manifold pressure and RPM and intake manifold
temperature. It does not use a mass air flow sensor.
The Wright Brothers piston engine ran sucking fuel vapor from a
heated open pan of fuel. No carburetor per se. No throttle.
No mass air flow sensor. Nada! Fuel flow was controlled by
a needle valve from a gravity feed fuel tank.
As I mentioned, Klaus's O-200 555 based system is a bit more
complicated but it does indeed run and run well. 100 MPG at
altitude and 110 Kts proves it. I see him start his engine
and take off almost every day as he is my next door hangar
neighbor.
Klaus's engine also runs with a constant speed dribble system
consisting only of a small tube, poked into the throttle body,
gravity drawing fuel from a header tank and using a fixed
throttle opening and at a given RPM.
Airplane engines are different from car engines. They have a
known and repetitive load verses RPM. Namely a propeller. There
are no requirements for rapid acceleration or rapid changes in
load
or RPM. Consequently the fuel system can be very rudimentary.
I am sure a simple 555 system as outlined here can be made to
work. Especially with the help of a wide band air/fuel sensor
giving only visual feed back and EGT monitoring. The pilot IS
the feed back loop adjusting the fuel air ratio at a fixed engine
load, throttle setting and altitude/temperature.
No computer necessary.
Paul Lamar ...No rotor no motor.
You aren't suggesting this kind of system to be THE efi system for all
aircraft rotary applications.. Right?
While the engine will run over a wide range of FA ratio settings, it
won't be very efficient except for within a small range. It seems that
it would likely foul plugs at 8/1 ratio.
Nice throttle response is a benefit. Plus, lower workload can improve
safety.
Being able to rack the throttle open from idle (without having the
engine backfire and cough) is a reasonable goal.
I understand Klaus' recent exercise/fitness program involved lots of
hand cranking of his EFI O-200 (which is now admittedly fixed). :)
Matt-
Oh you want throttle response :)
Everybody does not have to use it. If you want throttle
response it would need to be more sophisticated.
It is an exercise in the simplest possible system
and I am considering using it instead of Megasquirt
for steady speed dyno BSFC and HP testing.
--
Paul Lamar ...No rotor no motor.
Makes perfect sense. At least, it will be interesting to
see how it works.
Matt-
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.