Subject: Super simple 555 based fuel injection system
From: Rotary Engine
Date: 5/2/2006, 9:43 PM
To: AAme


I just thought of something real simple and low cost. If the variable
resister controlling the 555 pulse width is mechanically connected to
the throttle it is almost a complete EFI system.  You will still have
to manually lean it at altitude with another variable resister
in parallel to the one connected to the throttle.

-----------------------------------------------------

The more I think about this idea the better I like it.

Two 555's one for each rotor firing two injectors.

One linear sensor for each 555 connected to the throttle cable.
(See the 3D) The diameter of the cable drum controls the
rate of change of pot resistance with throttle movement.
For a two inch throttle cable movement and a .64 diameter
drum the pot will rotate 360 degrees. Resistance will
go from zero to max.

One aux leaning pot for each 555. That way you can control
the EGT or mixture on each rotor separately. Also gives a bit
of redundancy as if one rotor EFI system craps out you still
have the other.

Two Hall effect sensors on the e-shaft .065" thick CR steel trigger
plate 180 degrees out... one for each rotor. The angular position
of the Hall sensors control when the fuel is injected.

This system is super cheap. Probably less than $100 for
all the parts. Hall sensors are less than $6 each. Pots
are less than $5 each. 555's less than $1. Then you have
the injector switching transistors.

You don't need a degree in computer science or electronics
to understand it or fix it. Any mechanic should be able to
build and fix it.

Probably no printed circuit board required. Can be wire
wrapped or point to point wiring.
--------------------------------------------------------

This is the fundamental reason why this system is simpler
and cheaper than a micro computer based system.
A $300 CPU system takes in one or two pulses from an $30 to $70
expensive inductive sensor on the e-shaft wheel, calculates
the RPM, decides when to fire the ignition, decides when
to inject the fuel, and decides how wide of a pulse the fuel
injector needs.

If you can accept fixed timing (all air cooled aircraft engines
have fixed timing) with both plugs firing
at the same time TWO $7 Hall effect sensors sensing
TWO teeth on one E-shaft sensor wheel can fire the integrated
ignition coils. Done! Finished! So much for the ignition.

If you use TWO more Hall effect sensors and TWO more teeth
on ANOTHER e-shaft sensor wheel they can fire two $1 555 8 pin
integrated circuit which in turn send out a variable
width pulse to the injectors. That takes care of the injector
pulse timing. Almost done. How does one control the width
of the pulse the 555 sends to the injector? Simple! Use TWO $5
variable resistors that sense throttle position.

These are the $7 Hall effect vane sensors to use.
http://catalog.sensing.honeywell.com/datasheet.asp?PN=4AV20F%2DT2&FAM=solid
state&P=2292 They are good to 125 C or 257 F. Klaus uses Hall effect sensors
for his ignition system and EFI system not expensive inductive
sensors.

BTW some might say throttle position is not what you want.
Intake manifold pressure sensing is what you want. True but intake
manifold pressure sensing is harder and more expensive to implement.
Not impossible as Klaus's 555 based system does it.

On the other hand this throttle position sensor system is set
to start and run super rich. Fine for starting and climb out.
When you get to cruise altitude you fine tune
the mixture just like an air cooled aircraft engine.

Also BTW note it is simple to adapt this system to a three rotor.
Just replicate everything one more time.

This system is close to a 75% mechanical fuel injection system.

Paul Lamar ...No rotor no motor.

If you don't need the redundancy  the hall effect sensors can
be fanned out in output by using an op amp such as a lm 324.
smale

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.