Paul,
You may want to rename this to: auto components for fuel or
something
similar.
Maybe this is a good time to solicit opinions on the system I have in
mind that maximizes the use of modern, efficient, high reliability
auto
components.
1) Dual in-tank auto fuel pump modules with integral fuel level
sensors
and strainers. Use the automobile electrical connectors.
Possibly use
the automobile hose connectors.
2) Fuel pressure regulation either with a conventional fuel pressure
regulator and a full flow return line or a Pulse width modulated fuel
pump speed control with a small bleed return line for air removal.
3) Fuel injection and main ignition control via a Haltech E6GMX
firing
one plug per rotor. This ECU is identical to the E6X, but has
connectors to plug directly into a General Motors wiring harness
and is
priced lower than the E6X. It has extra PWM outputs that can be
controlled by any of the input signals it is monitoring. It could
control a turbo wastegate and the fuel pump speed/pressure. It
has full
data logging and is easy to program. Use GM ignition coils, pressure
sensors, and temperature sensors for engine control. On the airframe
use GM heater servos for flight control trim and use auto HID
headlamps
for landing/taxi. A couple of salvaged GM wiring harnesses would
yield
more than enough connectors for the entire aircraft. Using a
consistent
set of connectors and a consistent methodology will improve
reliability.
4) Redundant ignition via a separate shaft position sensor, fixed
timing, waste spark, firing one plug per rotor. Use a simple GM four
terminal ignition module. This could be changed to a flywheel mounted
magneto if such becomes available.
5) Limp home fuel system via one or two extra injectors manually
regulated by a simple PWM control circuit. This could be made
non-electrical by using a needle valve that meters fuel into the
manifold.
I see little value to having two complete ECU systems because if one
fails, the only use for the backup is to land safely ASAP....not to
complete the mission.
Aubrey
Aubrey
Many fine point you brought up here.
#3. You might consider sourcing the connectors used in marine
applications
that are waterproof by injecting a grease inside them prior to
crimping and
heat shrinking.
#5. Excellent idea about the back-up extra non electrical needle valve
injectors. What is a PWM control circuit?
Doug in Japan
Doug,
A Pulse Width Modulation, or PWM, circuit consists of a square wave
generator that produces output pulses of varying duty cycle or "on
time". If a PWM circuit is used to power a lamp or a DC motor the
average power delivered to the lamp or motor would be proportional to
the percentage duty cycle of the square wave pulses. If we power a
fuel
injector with the pulses then the fuel delivered would be proportional
to the percentage duty cycle of the pulses. As an emergency fuel
source, there would be a potentiometer control knob for the pulse width
circuit mounted so it could be conveniently manipulated at the same
time
as the throttle. They would be adjusted for stable engine operation at
whatever power level was desired.
Aubrey
The integrated circuit part you use is called a 555 and
cost about a buck at Radio Shack. There is a dual version
called a 556.
The trigger input comes from a sensor on the e-shaft
and the the variable resistor Aubrey mentioned above controls
the pulse width. There fore the amount of fuel injected
is directly proportional to RPM and the pulse width
setting of the potentiometer.
This is the heart of Klaus's EFI system.
You should have no trouble keeping the engine running
with this system at a fixed throttle opening.
Paul Lamar ...No rotor no motor.
Aubrey, Paul,
Thanks. Yes I know about Pulse Width Modulation. We use the
technique to
control our wind generator speed and output. Somehow the
combinations of
letters didn't click in my mind. Of course BTW took me quite a while as
well. Yes the circuit is extremely simple but still requires electrical
power for the injectors.
Has anyone considered using Klaus's Lightspeed capacitor discharge
system in
parallel with a Magneto mounted where the distributor or rpm Hall effect
sensor now resides?
Doug Fir
Lots of people use Klaus ignition system in conjunction with
a mag on air cooled aircraft engines.
There is no getting around some electrical on a low wing
airplane unless you rig a mechanical fuel pump. Of course you also
need an electrical starter.
I just thought of something real simple and low cost. If the variable
resister controlling the 555 pulse width is mechanically connected to
the throttle it is almost a complete EFI system. You will still have
to manually lean it at altitude with another variable resister
in parallel to the one connected to the throttle.
-----------------------------------------------------
The more I think about this idea the better I like it.
Two 555's one for each rotor firing two injectors.
One linear sensor for each 555 connected to the throttle cable.
(See the 3D) The diameter of the cable drum controls the
rate of change of pot resistance with throttle movement.
For a two inch throttle cable movement and a .64 diameter
drum the pot will rotate 360 degrees. Resistance will
go from zero to max.
One aux leaning pot for each 555. That way you can control
the EGT or mixture on each rotor separately. Also gives a bit
of redundancy as if one rotor EFI system craps you you still
have the other.
Two Hall effect sensors on the e-shaft steel trigger plate
180 degrees out... one for each rotor. The angular position of
the Hall sensors control when the fuel is injected.
This system is super cheap. Probably less than $100 for
all the parts. Hall sensors are less than $6 each. Pots
are less than $5 each. 555's less than $1. Then you have
the injector switching transistors.
You don't need a degree in computer science or electronics
to understand it or fix it. Any mechanic should be able to
build and fix it.
Probably no printed circuit board required. Can be wire
wrapped or point to point wiring used.
Paul Lamar
Aubrey,
Correct me if I am wrong here but I am not sure how the wiring
would look on the following system.
Assume the primary spark supply would be a capacitance charged
system, (either Klaus' or the Honda Integra) and direct drive
magneto as a back-up.
If for some reason the electrical system goes south I am assuming
the DC input to the capacitance charge would be disabled and the
magneto grounded through a DPDT or rotary switch.
Q. Where is the junction from the two energy sources joined
before heading to the spark plugs?
Thanks
Doug Fir
How would a magneto and a be wired to the ignitor coils.
One of them would have to be primary and other a standby
system I assume. Standby would be the flywheel, or magneto.
Doug,
The primary system would be LS-1 or similar GM ignitors driven by the
fuel injection/ignition computer and powered from the airframe
electrical system. This system would consist of two ignitors, each
firing one plug on each rotor. The spark timing advance would be
controlled by the computer.
The back-up system would be entirely separate and would fire the other
plug on each rotor at a fixed spark advance. This system would either
use two additional ignitors similar to the primary system that are
driven by an eccentric shaft position sensor and a simple ignition
module, or it would use some kind of self-energized spark system. I
used the term "magneto" in referring to the self-energized spark
system. I was not thinking of an aircraft type magneto, but rather, the
type of system that is found in small engines and some outboard motors.
It has been shown that at high power levels, the timing of the second
spark plug has little effect on performance. So, there is no
significant performance loss from firing the second plug at a fixed
timing advance. There is a Ford ignition module that accepts an
advanced spark signal from a computer and a fixed spark signal from a
shaft position sensor and uses whichever signal comes first. Thus, it
would revert to fixed timing if the computer failed. But, I doubt it is
worth the extra trouble and expense over the simple 4 terminal GM
ignition module.
In summary, the primary and back-up systems would be separate and no
switching would be required in the event of a computer failure. I plan
to have a second battery for back-up power. I haven't decided yet how I
want to connect it to the system. I like the Blue Mountain electric
control board. It has a provision for connecting a second battery. The
batteries are isolated from each other by diodes and the board takes
current from the one that has the highest voltage. I may use the Blue
Mountain board or make a similar one (the BM board is a little pricey at
$900).
Aubrey
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.