>> Paul and group,
>> I finally have my Renesis mounted, and now I need to pursue the
>> cooling. I've studied Paul's articles and all the cooling threads
>> here, but it looks like I may have several options. I would
>> appreciatesome help so I might have a chance of getting it as
close
>> to right as
>> possible!
>> As per the attached pix, it is obvious that the standard
cowling is
>> far too wide (about 30", and just a little short) for this
engine. I
>> can narrow the two bottom cowling halves without any problem,
but the
>> fit around the prop. is still too big.
>> Perhaps I should just implement the best possible cooling
scheme and
>> build a new cowling to fit. Other than overall drag, there are
very>> few real constraints on the size and shape of a custom
cowling for
>> this plane. Cooling is obviously more important.
>> For the radiators, it looks like there are at least 2 reasonable
>> options. The first is to put two radiators sitting at about a 45
>> degree angle back, and tilted back from the top, in front of the
>> engine(see pic). This can support two radiators about 17x12",
but
>> does not
>> account for the oil cooler. I can make appropriate ducting to
both of
>> these without too much trouble. This has been done by other Goose
>> builders, but with small radiators and no ducting. It seems
like this
>> option needs quite a bit of width to work.
>> Another option might be to put a slightly larger, single
radiator in
>> the front, and another radiator (or two) on the cool side of the
>> engine. The side looks like it could easily handle a radiator
about>> 14x22" Notice the RX-7 oil cooler in this location on one
pic. This
>> would have to use a 90-degree-entry style duct that fed from
the
>> frontof the cowling, beside the front radiator. The hot air
could
>> exiteither out the side of the cowling, or toward the engine.
This
>> wouldgive a much narrower cowling than with 2 radiators up front.
>> The side version could handle the stock oil cooler (5"x22") as
well as
>> a 9x22" water radiator. However, there is another possibility
for an
>> oil radiator if I still need more volume. Down under the rear
>> supportbridge (see pic), there is a space that would handle
about
>> 10x14"radiator. Air would have to be ducted down to this area,
but I
>> could
>> probably get a 4" diameter tube to it. It might also need a
fan,>> because it would get no airflow unless the plane was moving.
Perhaps
>> an automotive-style fan and fan shroud might work? Some
builders
>> haveplaced the 0-320 cooler in this location, with mixed
results. No
>> one
>> has used a fan.
>> The Goose normally ingests a lot of air through its appx. 9"x15"
>> intake, and sends most of it into the pylon after cooling the
engine.>> It exits at the rear of the pylon through 'augmentation
slots'>> supposedly to help deliver air to the prop. This is
obviously more
>> intake area than is necessary just to cool the engine.
>> Is there a better solution than any of these ideas? I suppose the
>> questions boil down to: what is the smallest, most efficient
way to
>> group water and oil radiators of certain sizes around the engine in
>> order to achieve the necessary cooling (240hp) with the least drag?
>> Your ideas and suggestions are greatly appreciated!
>> Thanks,
>> Scott Gettings
>> Real nice work on the motor mount Scott.
>> I think you are being a bit optimistic on the HP.
>> With only four ports and a 2.85:1 PSRU you will
>> be limited to about 7000 to 7500 and about 190 HP
>> +/- 10 HP depending on the muffler and prop. Given that, one
>> 17" x 12" x 2" rad should work fine with a K&W truncated
>> well sealed diffuser vertically mounted in front of the engine.
>> The oil cooler can go on the plug side in a simple
>> K&L wedge diffuser. A Paul Lipps prop mounted close
>> to the rear cowl opening will enhance the air flow
>> through the engine compartment and the heat exchangers.
>> More pictures next meassge.
>> Paul Lamar ...No rotor no motor.
>> Opss I counted wrong. That should be six ports and
>> 215 HP +/- 10 HP.
>> --
>> Paul Lamar ...No rotor no motor.
>
>
> Thanks for your help, Paul. I couldn't have done the engine
mounts
> without your and the group's help.
> Although I didn't end up using the oil pain-mount combination you
> suggested (couldn't find anyone to build it),
> using two, 1x2", 4130 horizontal beams ended up being very light,
> simple and inexpensive. Ed will be building
> my custom oil pan that fits between the beams, starting with the
flat
> flange you see on the engine.
>
> Regarding the radiators, I'm assuming I should allocate intake
areas
> according to the 20% rule?
> - 20% of 17x12", or 41 sq. inches for the front radiator
> - 20% of 5x19" for the oil cooler, or about 20 sq. inches
>
> I'll need another 7-10 sq. inches for the intake, but have plenty
to
> play with due to the larger intake area
> (normally about 140 sq inches). Should I allocate larger intake
areas
> to the coolers? All this air will end up
> going out the rear of the pylon.
>
> thanks again,
>
> Scott Gettings
>
> Yes I think 20% is about right for the speed range
> of your airplane. Yes a large air out let in front of the
> prop won't hurt the drag that much. My guess is about
> 14 or 16 inches in diameter with a 12 inch pressure recovery
> spinner around one of Paul Lipps pusher props.
>
> Paul Lamar ...No rotor no motor.
>
>
Thanks again, Paul. I'll go with the 20% rule for the radiators.
Let me be sure I understand the prop exit air concept: The cowl
diameter should be 14-16" at the prop flange and the prop spinner 12"
at this location? Is this to try and get all of the intake air out
around the prop?
In the Goose/Seahawk, some of the air is supposed to go out through
augmentation slots at the end of the pylon. This is to feed more air
to the prop in its worst-airflow location. No one knows how much,
butthe total intake area is usually far larger than needed to cool the
engine. The slots appear very important. Without them, there is a
LOTmore prop noise and vibration.
The slots are usually a single row of about 2.5-3" x 4" cutouts in the
rear of the pylon, usually about 5 will fit. This is only about 60
sq.inches. I don't have a picture off the most current version,
but here
are pix of a couple of others.
A nagging question is whether to try and get more air to come out the
slots with a tightly cowled prop spinner and large slots, or just let
it come out where it may. It sounds like an implementation for your
water manometers. Hopefully I'll be able to arrive at the best
solution before cutting holes or building a new cowling. If larger
slots are needed, would two rows just off-center of the pylon rear
(similar to the second picture) be best?
Scott Gettings
"Let me be sure I understand the prop exit air concept: The cowl
diameter should be 14-16" at the prop flange and the prop spinner 12"
at this location?"
Yes. That gives a opening area of about 100 square inches.
"Is this to try and get all of the intake air out around the prop?"
Yes and a high angle prop blade such as Paul Lipps implemented
is required to suck the air out at low speeds.
Here are some pictures of Charley Airesman arrangement.
Klaus at LSE makes and sells these kinds of spinners.
Paul Lamar ...No rotor no motor.
Got it, thanks. This helps a lot.
Scott Gettings
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.