Subject: Cooling a Glass Goose
From: Rotary Engine
Date: 5/17/2006, 10:30 AM
To: AAme


> Paul and group,
> > I finally have my Renesis mounted, and now I need to pursue the
> cooling.  I've studied Paul's articles and all the cooling threads
> here, but it looks like I may have several options.  I would appreciate> some help so I might have a chance of getting it as close to right as
> possible!
> > As per the attached pix, it is obvious  that the standard cowling is
> far too wide (about 30", and just a little short) for this engine.  I
> can narrow the two bottom cowling halves without any problem, but the> fit around the prop. is still too big.
> > Perhaps I should just  implement the best possible cooling scheme and> build a new cowling to fit.  Other than overall drag, there are very
> few real constraints on the  size and shape of a custom cowling for
> this plane.  Cooling is obviously more important.
> > For the radiators, it looks like there are at least 2 reasonable
> options.  The first is to put two radiators sitting at about a 45
> degree angle back, and tilted back from the top, in front of the engine> (see pic).  This can support two radiators about 17x12", but does not
> account for the oil cooler. I can make appropriate ducting to both of
> these without too much trouble.  This has been done by other Goose
> builders, but with small radiators and no ducting.  It seems like this> option needs quite a bit of width to work.
> > Another option might  be to put a slightly larger, single radiator in
> the front, and another radiator (or two) on the cool side of the
> engine.  The side looks like it could easily handle a radiator about
> 14x22"  Notice the RX-7 oil cooler in this location on one pic.  This> would  have to use a 90-degree-entry style duct that fed from the front
> of the cowling, beside the front radiator.  The hot air could exit
> either out the side of the cowling, or toward the engine.  This would> give a much narrower cowling than with 2 radiators up front.
> > The side version could handle the stock oil cooler (5"x22") as well as
> a 9x22" water radiator.  However, there is another possibility for an
> oil radiator if I still need more volume.  Down under the  rear support> bridge (see pic), there is a space that would handle about 10x14"> radiator.  Air would have to be ducted down to this area, but I could
> probably get a 4" diameter tube to it.    It might  also need a fan,
> because it would get no airflow unless the plane was moving.  Perhaps> an automotive-style fan and fan shroud might  work?  Some builders have
> placed the 0-320 cooler in this location, with mixed results.  No one> has used a fan.
> > The Goose normally ingests a lot of air through its appx. 9"x15"
> intake, and sends most of it  into the pylon after cooling the engine.> It exits at the rear of the pylon through 'augmentation slots'> supposedly to help deliver air to the prop.  This is obviously more
> intake area than is necessary just to cool the engine.
> > Is there a better solution than any of these ideas?  I suppose the
> questions boil down to:  what is the smallest, most efficient way to
> group water and oil radiators of certain sizes around the engine in
> order to achieve the necessary cooling (240hp) with the least drag?
> Your ideas and suggestions are greatly appreciated!
> > Thanks,
> > Scott Gettings
> > Real nice work on the motor mount Scott.
> > I think you are being a bit optimistic on the HP.
> With only four ports and a 2.85:1 PSRU you will
> be limited to about 7000 to 7500 and about 190 HP
> +/- 10 HP depending on the muffler and prop. Given that, one
> 17" x 12" x 2" rad should work fine with a K&W truncated
> well sealed diffuser vertically mounted in front of the engine.
> The oil cooler can go on the plug side in a simple
> K&L wedge diffuser. A Paul Lipps prop mounted close
> to the rear cowl opening will enhance the air flow
> through the engine compartment and the heat exchangers.
> > More pictures next meassge.
> > Paul Lamar ...No rotor no motor.

>Here's what I did.
Bill Hyde

I assume it is working well Bill.
Did you fix the crash landing damage?

Paul Lamar



Thanks, Bill.

What is the size of your front radiator and cowl intake?
I see you used the stock oil cooler.

Did this arrangement cool satisfactorily?

Scott Gettings



The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.