Subject: Cooling a Glass Goose
From: Rotary Engine
Date: 5/18/2006, 8:21 AM
To: AAme



> Paul and group,
>
> I finally have my Renesis mounted, and now I need to pursue the
> cooling.  I've studied Paul's articles and all the cooling threads
> here, but it looks like I may have several options.  I would
appreciate> some help so I might have a chance of getting it as close to right as
> possible!
>
> As per the attached pix, it is obvious  that the standard cowling is
> far too wide (about 30", and just a little short) for this
engine.  I
> can narrow the two bottom cowling halves without any problem, but
the> fit around the prop. is still too big.
>
> Perhaps I should just  implement the best possible cooling scheme
and> build a new cowling to fit.  Other than overall drag, there are very
> few real constraints on the  size and shape of a custom cowling for
> this plane.  Cooling is obviously more important.
>
> For the radiators, it looks like there are at least 2 reasonable
> options.  The first is to put two radiators sitting at about a 45
> degree angle back, and tilted back from the top, in front of the
engine> (see pic).  This can support two radiators about 17x12", but does not
> account for the oil cooler. I can make appropriate ducting to
both of
> these without too much trouble.  This has been done by other Goose
> builders, but with small radiators and no ducting.  It seems like
this> option needs quite a bit of width to work.
>
> Another option might  be to put a slightly larger, single
radiator in
> the front, and another radiator (or two) on the cool side of the
> engine.  The side looks like it could easily handle a radiator about
> 14x22"  Notice the RX-7 oil cooler in this location on one pic.
This> would  have to use a 90-degree-entry style duct that fed from the front
> of the cowling, beside the front radiator.  The hot air could exit
> either out the side of the cowling, or toward the engine.  This
would> give a much narrower cowling than with 2 radiators up front.
>
> The side version could handle the stock oil cooler (5"x22") as
well as
> a 9x22" water radiator.  However, there is another possibility
for an
> oil radiator if I still need more volume.  Down under the  rear
support> bridge (see pic), there is a space that would handle about 10x14"> radiator.  Air would have to be ducted down to this area, but I could
> probably get a 4" diameter tube to it.    It might  also need a fan,
> because it would get no airflow unless the plane was moving.
Perhaps> an automotive-style fan and fan shroud might  work?  Some builders have
> placed the 0-320 cooler in this location, with mixed results.  No
one> has used a fan.
>
> The Goose normally ingests a lot of air through its appx. 9"x15"
> intake, and sends most of it  into the pylon after cooling the
engine.> It exits at the rear of the pylon through 'augmentation slots'> supposedly to help deliver air to the prop.  This is obviously more
> intake area than is necessary just to cool the engine.
>
> Is there a better solution than any of these ideas?  I suppose the
> questions boil down to:  what is the smallest, most efficient way to
> group water and oil radiators of certain sizes around the engine in
> order to achieve the necessary cooling (240hp) with the least drag?
> Your ideas and suggestions are greatly appreciated!
>
> Thanks,
>
> Scott Gettings
>
> Real nice work on the motor mount Scott.
>
> I think you are being a bit optimistic on the HP.
> With only four ports and a 2.85:1 PSRU you will
> be limited to about 7000 to 7500 and about 190 HP
> +/- 10 HP depending on the muffler and prop. Given that, one
> 17" x 12" x 2" rad should work fine with a K&W truncated
> well sealed diffuser vertically mounted in front of the engine.
> The oil cooler can go on the plug side in a simple
> K&L wedge diffuser. A Paul Lipps prop mounted close
> to the rear cowl opening will enhance the air flow
> through the engine compartment and the heat exchangers.
>
> More pictures next meassge.
>
> Paul Lamar ...No rotor no motor.

>Here's what I did.
Bill Hyde

I assume it is working well Bill.
Did you fix the crash landing damage?

Paul Lamar


Thanks, Bill.

What is the size of your front radiator and cowl intake?
I see you used the stock oil cooler.

Did this arrangement cool satisfactorily?

Scott Gettings



I don't have that aircraft anymore. The cowling was made by me (way to much work). The radiator was custom made and the oil cooler was provided by the same company (not stock but same volume). They are located in Indianapolis but I can't recall their name.
Bill Hyde


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.