Subject: Abstract of AIAA tech paper
From: Rotary Engine
Date: 5/21/2006, 11:41 PM
To: AAme



Here is a rough draft of the Abstract of my AIAA
paper on turbo compound sthat I will present at the
Jan 07 meeting of the AIAA in Reno Nevada.

Please read it over and make any and all comments.
I need to submit it by the 22th tommorrow.




Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.

------------------------------------------------------------------------

Turbo compound Wankel rotary engine.
Paul Lamar

Rotary Engine Newsletter
Santa Paula California
rotaryeng@earthlink.net
www.rotaryeng.net



TURBO COMPOUNDING THE ROTARY

A turbo-compound engine passes the exhaust gasses {collects all of the exhaust gasses and runs them} through a turbine, with {all of} the power generated {going} being fed back into the crankshaft {and ultimately to the
propeller} thereby recovering some of the waste heat in the exhaust. Ref 1.

1954 SAE Transactions. Development of the R3350 Turbo
Compound Engine.
Besides the economic advantage of turbo compounding an engine there are other considerations.

{Short range also cuts into long trip times and limits your weather options making the airplane less safe.

Having the range to turn back  has saved my life
more than once when on a long cross country's over remote areas of Canada,
Alaska and Baja. A high performance airplane with a small thin wing has a
limited volume for fuel. Such air cooled piston engine airplanes may need
to stop every 400 or 500 miles for fuel.}
Turbo compounding also improves the power to weight ratio of {an} the engine by roughly 20%. Ref 1.

 

Edit the Allison PP down to one or two sentences

Allison built a V12 turbo compound engine during World War II in an
attempt to recover some of the waste energy resulted in a turbo-compound
configuration. Ref 2 It was identified as the V1710-E22. Work began in 1944 and continued until 1946. It was sponsored
by the US government but canceled with the advent of the turbine
engine. Apparently it was the first turbo-compound engine.
The V1710-E22 had a military rating of 2320 hp, and a War
Emergency Rating with water/alcohol injection of 3090 hp.
With a compression ratio of 6:1 it achieved a 19% improvment
in the BSFC. It never flew. The normal supercharged Allison V12 generated  2000 take off HP and 2500 HP War Emergency Rating.
Ref 2
Vee's For Victory by Daniel D. Whitney. Schiffer Miltary History
1998 ISBN 0-7643-0561-1
 

Edit the R3350  PP down to one or two sentences

The most widely used turbo-compound engine was a version of the air-cooled,
18-cylinder, two-row radial Curtiss Wright R3350-TC. Ref (1) Used in many airliners and several miltary aircraft. Thousands were built. This engine had three turbines, each fed by 6 cylinders, that were geared to the crankshaft.
The normal supercharged version produced 2700 hp and weighed 2850 lbs.
The BSFC was as low as .37 at sea level and .33 at 30,000 feet with
a compression ratio of 7.2:1. The turbo-compounded version produced 3500 hp and weighed 3440 lb resulting in a power to weight ratio of over
unity. The worlds record prior to the Rutan Voyager for un-refueled distance was held by a P2V that flew from Australia to Ohio.  Super G Lockheed Constelations  with this engine were able to fly non-stop LA to London over the pole in the 1950's.
Ref 1a. "Lockheed Constellation" by Stringfellow &
Bowers Motorbooks ISBN 0-87938-379

{The Achilles heel of this engine proved over time to be the failure of the exhaust valves when the exhaust gas pressure was 25% higher than the intake pressure. Much of the developement effort was expending on improvements in exhaust valve durabilty.}


Another protoype turbo-compound engine {is} was the Napier Nomad, which was built in England. It was a 12-cylinder, horizontally opposed, liquid cooled, valve-less, 2-stroke cycle Diesel engine with a 3-stage turbine. It reached flight test but not production. BSFC was .345 (shaft HP) at 11,000 feet {and a compression ratio of 8.25}. Ref 3

Ref 3 A history of Aircraft Piston Engines by Herchel Smith
Sunflower University Press Corrected editon 1986 ISBN 0-89745-079-5


NACA  sponsored several reports on turbo compound engines.
One of which used a dynamometer {data} to gather data.
This test program indicated a BSFC of .323 at 10,000 feet.
14% better at 10,000 feet and 21% better at 30,000 feet.
 
Ref 4

NACA REPORT No. 822 1944






The Wankel rotary engine is a very mechanically robust engine that tolerates high boost pressures. There are no cyclical reversing stresses in the three major moving parts that lead to fatique failure
in the light weight  piston engine. Consequently the power to weight
ratio of the current Mazda RX8 Wankel rotary engine is comparable to an
air cooled aircraft engine at 240 HP and 190 pounds less the weight
of the required PSRU.
 

Save this PP for the paper

{The compression ratio is inherently low limited to about 10:1 due the neccesit{t}y of locating the combustion chamber in the rotor. The combustion chamber surface to volume ratio is high affecting the
efficiec{n}y of combustion but adding to the ability of the engine
to survive high power to displacement ratios.} 
The Wankel rotary has no exhaust valves. Porting is done by the rotor
as it orbits the inside of the rotor housing. The Wankel rotary has approxmately three times the net available kinetic energy in the exhaust as compared to a piston engine. Two thirds of the total kinetic energy in the exhaust of a piston{e} engine is dissipated by the exhaust valves. Ref 1

The high level of kinetic energy in the Mazda Wankel rotary engine exhaust has been well documented.  {known for 30 years}  {Anybody that has been present at
race where a  Mazda Wankel rotary powered race car operated a muffler can appreicate the tremendous  kinetic energy in the exhaust.} There is always as much or more potential HP in the exhaust as there is available from the output shaft. (Ref 6) {The more you boost it the more HP is available to boost it.  This is an exponential effect so the real HP limit is detonation, durability and structural strength of the core engine.} Turbo charged Mazda 2.6 liter two rotor engines
have been boosted to 800 HP for racing purposes using alcohol
and nitrous oxide. The Wankel rotary appears to be an ideal gas generator for a turbine. {engine.} 

Ref 6 Rotary Engine. by Kenichi Yamamoto. Sankaido Company Ltd. 1981 In English. No ISBN number.
BUILDING A TURBO COMPOUND WANKEL ROTARY ENGINE.

 

Save this PP for the paper

{I had an idea on how to implement a turbo compound arrangement using a ball traction drive gear box from a Paxton Centrifugal supercharger. The HP, gear reduction and RPM is about right for connection  a turbine and feeding the power back into the engine instead of removing it. Hopefully we will get 20% more power with no more fuel and no additional load on the engine cooling system.}

 

This paper describes a proof of concept turbo compound arrangement that utilizes the stock Mazda turbocharger to feed mechanical energy through a speed reducer back to the engine shaft.  The speed reducer consists of a friction (traction) "gear" drive capable of reducing the 60,000 RPM to 100,000 RPM turbine speed down to the 7500 RPM speed of the engine shaft.  The speed reducer drives the engine shaft via a multi-V belt.  Preliminary indications are that as much as 50 HP can be recovered from the waste heat in the rotary exhaust thus improving the BSFC from the current .47 to .38 at cruise altitude. The range of any airplane using
this engine would increase by 25%. {My compound setup for the rotary would use one turbo charger turbine feeding power into the eccentric shaft and an  turbo charger centrifugal blower using modern aerodynamics from a stock Mazda turbocharger.}

Save this PP for the paper

{We will start with a turbine reduction gear ratio that peaks the torque feed back to what the  engine will tolerate at sea level and at an e-shaft RPM of 7500. That e-shaft RPM assumes you are using a PSRU with a 2.85:1 reduction ratio and a maximum prop RPM of 2630.}  The historical evidence suggest we will eventually get more than a 20%
efficiency improvement with a turbo compound rotary.


{We are now building a device to extract the excess HP from
a stock turbo charger. Input speed RPM can be up to 100,000 RPM and output
RPM will be one tenth of that. The power from the traction drive output shaft will be transfered to the e-shaft of the rotary by a V-Ribbed belt to absorb
the torsional vibrations from the rotary engine. We hope to recover at least}
{We hope to test the engine soon on a dyno}



Stratified Charge Rotary Engine Critical Technology Enablement Volume II NASA Contractor Report 189106
APPENDIX C DATE 10/04/91
Turbomachinery System Analysis For stratified Charqe Rotary Engine.
Sunstrand Aerospace

C.E. Irion and R.E. Mount
Rotary Power International, Inc.
Wood-Ridge, New Jersey
 

Paul,
I am just returning from the Mid Atlantic Fly-In.  I hope it is not too
late to provide some input.

A couple of general comments:  I think, for an abstract, it is too
long.  I would include fewer details about the historical projects.
Just say that they were done and what benefits were seen.  The details
will be in the paper.  For the description of the current project, the
turbo compound rotary, use the present or past tense in describing it
because that will be the perspective when the paper is delivered.

I'll mark up your text above and use brackets { } where I would remove
passages of  text.


If I cut and paste it together, here is what it would look like:


Turbo compound Wankel rotary engine.
Paul Lamar

Rotary Engine Newsletter
Santa Paula California
rotaryeng@earthlink.net
www.rotaryeng.net



TURBO COMPOUNDING THE ROTARY

A turbo-compound engine passes the exhaust gasses through a turbine, with the power generated being fed back into the crankshaft thereby recovering some of the waste heat in the exhaust.

Ref 1.

1954 SAE Transactions. Development of the R3350 Turbo
Compound Engine.

Besides the economic advantage of turbo compounding an engine, there are other considerations.  Turbo compounding also improves the power to weight ratio of the engine by roughly 20%. Ref 1.

Allison built a V12 turbo compound engine during World War II.  It was identified as the V1710-E22. With a compression ratio of 6:1 it achieved a 19% improvement
in the BSFC.

Ref 2

Vee's For Victory by Daniel D. Whitney. Schiffer Miltary History
1998 ISBN 0-7643-0561-1

The most widely used turbo-compound engine was a version of the air-cooled,
18-cylinder, two-row radial, the Curtiss Wright R3350-TC. This engine was used in
many airliners and several military aircraft. The BSFC was as low as .37 at sea level and .33 at 30,000 feet with a compression ratio of 7.2:1.

Ref 1a. "Lockheed Constellation" by Stringfellow &
Bowers Motorbooks ISBN 0-87938-379

Another prototype turbo-compound engine was the Napier Nomad, which was
built in England. It was a 12-cylinder, horizontally opposed, liquid cooled,
valve-less, 2-stroke cycle Diesel engine with a 3-stage turbine.  BSFC was .345  at 11,000 feet with a compression ratio of 8.25. Ref 3

Ref 3 A history of Aircraft Piston Engines by Herchel Smith
Sunflower University Press Corrected edition 1986 ISBN 0-89745-079-5


The Wankel rotary has no exhaust valves. Porting is done by the rotor
as it orbits the inside of the rotor housing. The Wankel rotary
has approximately three times the net available kinetic energy in the
exhaust as compared to a piston engine. Two thirds of the total kinetic
energy in the exhaust of a piston engine is dissipated by the exhaust
valves. Ref 1

The high level of kinetic energy in the Mazda Wankel rotary engine
exhaust has been well documented.  There is always as much or more potential HP in the exhaust as there is available from the output shaft. (Ref 6)
Turbo charged Mazda 2.6 liter two rotor engines have been boosted to 800 HP for racing purposes using alcohol and nitrous oxide. The Wankel rotary appears to be an ideal gas generator for a turbine.

Ref 6 Rotary Engine. by Kenichi Yamamoto.
Sankaido Company Ltd. 1981 In English. No ISBN number.

This paper describes the construction and preliminary dynomometer testing of a proof of concept turbo compound engine arrangement that utilizes the stock Mazda turbocharger to both turbocharge the engine and feed mechanical energy through a speed reducer back to the shaft of a Mazda 13B engine.  The speed reducer consists of a friction (traction) "gear" drive capable of reducing the 60,000 RPM to 100,000 RPM turbine speed down to the 7500 RPM speed of the engine shaft.  The speed reducer drives the engine shaft via a multi-V belt.  Preliminary indications are that as much as 50 HP can be recovered from the waste heat in the rotary exhaust thus improving the BSFC from the current .47 to .38 at cruise altitude. The range of any airplane using this engine would increase by 25%.

Aubrey

-------------------------------------------------------

Thanks Aubrey. Good constructs. The dead line is 33 minutes from now.
But I think I get to edit it a few times :)
I thought I had another 3 days but I was wrong and got
panicked. Particularly because my ISP has been acting up.
Normally I would work on it for a couple of days or so.

Here is the draft actually uploaded. It was supposed to be
1000 words but it came out to about 1400.

I am sure they use the abstract in it present form to decide which
papers will be accepted. This is not the final form of the abstract
that will appear in the final paper. In the past they have
been very helpful with editing.

BTW how was the Mid Atlantic flyin? I know Tracy Crook
and Ed Anderson went. Any other rotaries show up?

Paul Lamar ...No rotor no motor.



The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.


Turbo compound Wankel rotary engine.
Paul Lamar

Rotary Engine Newsletter
Santa Paula California
rotaryeng@earthlink.net
www.rotaryeng.net



TURBO COMPOUNDING THE ROTARY
Besides the economic advantage of a .38 BSFC there are other consideration
for turbo compounding an aircraft engine.

Short range also
cuts into long trip times and limits your weather options making the
airplane slightly less safe.

 Having the range to turn back  has saved my life
more than once when on a long cross country's over remote areas of Canada,
Alaska and Baja. A high performance airplane with a small thin wing has a
limited volume for fuel. I don't think I would be happy with a
airplane if I had to stop every 400 or 500 miles for fuel. 

Almost all 300 MPH airplanes use thin wings. 
The thickness is around 12% and the cord limited. 60 gallons or so would typical.

A 300 HP  engine might cruise at 225 HP at speed of 275 MPH
less 35 MPH head wind (One always has a head wind. A tail wind is a rare
occurrence.) equals 240 MPH. The BSFC for a normally aspirated two rotor
is 117 pounds per hour divided by six pounds per gallon is 19.5 gallons per
hour. That gives me a max endurance of about three hours or about 720 mile
range. Not really enough to go anywhere serious. That is also BTW $39
dollars an hour fuel cost at 2 bucks a gallon for 100LL. 20% more range than
that would be nice or 864 miles and a $400 a year savings at 100 hours. That
is a BSFC of about 0.42 or about the same as some of the best aircraft
piston engines. Running the engine 100 degrees F lean of peak will improve
that to better than a piston engine.

HISTORY OF THE TURBO-COMPOUND By John Leonard 

The first V 1710 produced 750 hp. By the beginning of World War 11 it was
producing 1050 hp, then 1125, then 1325, and late model P-38's got 1475. But
engineers recognized that there was a lot of energy going out the exhaust
pipes.

 An attempt to recover some of this energy resulted in the turbo-compound
V1710 shown at the bottom of the page. It was identified as the V1710-E22 by
Allison, and as the V1710-127 by the government. A turbo-compound engine
collects all of the exhaust gasses and runs them through a turbine, with all
of the power generated going back into the crankshaft and ultimately to the
propeller. It differs from a turbo-supercharged engine, which uses exhaust
gas energy to increase the pressure of incoming air. Work on this engine
began in about 1944 and continued until 1946, when Allison asked that it be
canceled because turbine engines had greater promise. It was the first
successful turbo-compound engine, and probably one of only three to ever be
built. This engine was designed to power the XP63H, which, as it turned out,
never flew. The V1710-E22 had a military rating of 2320 hp, and a War
Emergency Rating with water/alcohol injection of 3090 hp.

 The Allison engine collected the exhaust gas from all 12 cylinders and
routed it to the turbine at the rear of the engine through two exhaust
tubes. The shaft from the turbine ran through the center of the first stage
supercharger impeller, back to the engine and put its power directly into
the crankshaft. The turbine could not be connected to the supercharger
impeller because the supercharger was driven by a variable speed
transmission, which did not run at a fixed speed ratio with respect to
either the crankshaft or the turbine. Since this engine was to power a P-63,
it used an extension shaft and a remote gearbox attached to the crankshaft
at the front of the engine at lower left in the picture below. This engine
represented quite an advancement over the original 750 hp engine.

 The most successful turbo-compound engine was a version of the air-cooled,
18-cylinder, two-row radial Curtiss Wright R3350-TC. This engine had three
turbines, each fed by 6 cylinders, that were geared to the crankshaft. The
normal version produced 2700 hp and weighed 2850 lbs. The turbo-compounded
version produced 3500 hp and weighted 3440 lb. This engine was used on the
Douglas DC-7c and some versions of the Lockheed Constellation. 
The other turbo-compound engine is the Napier Nomad, which was built in 
England. It was a 12-cylinder, horizontally opposed, liquid cooled, 
valve-less, 2-stroke cycle Diesel engine with a 3-stage turbine. It 
reached flight test but not production.

-----------------------------------------------------------------------



-----------------------------------------------------------------------------
NACA REPORT No. 822

CALCULATIONS OF ECONOMY OF 18-CYLINDER RADIAL AIRCRAFT ENGINE
WITH EXHAUST-GAS TURBINE GEARED TO THE CRANKSHAFT

By RICHARD W. HANNUM and RICARD H. ZIMMERMAN

SUMMARY

Calculations based on dynamometer test-stand data obtained on an 18-cylinder radial
engine were made to determine the improvement in fuel consumption that can be
obtained at various altitudes by gearing an exhaust gas turbine to the engine
crankshaft in order to increase the engine-shaft work. The calculations indicted
that, for turbine and auxiliary supercharger efficiencies of 85 percent minimum
net brake specific fuel consumption improvements of 0.357 pound per brake horse
hour at an altitude of 10,000 feet and of 0.323 pound per brake horsepower hour
at 30,000 feet can be obtained by gearing the exhaust-gas turbine to the engine
crankshaft and operating that engine at a speed of 2,000 rpm, an inlet-manifold
pressure of 40 inches [5 psi boost] of mercury absolute, and a fuel-air ratio
of 0.063 [12:1].

The reduction in net brake specific fuel consumption that can be obtained if
the exhaust-gas turbine supplies all the auxiliary  supercharger power and if
its residual power is transmitted through gears to the engine crankshaft as
compared with auxiliary turbo supercharging, is approximately 14 percent at
an altitude of 10,000 feet and 21 percent at 30,000 feet.
The net brake specific fuel consumption is a minimum is for engine exhaust
gas pressure approximately 25 percent above inlet-manifold pressure and varies
only slightly from that minimum for a range of exhaust gas pressure
from 6 to 45 percent above inlet-manifold pressure.

INTRODUCTION

The use of an exhaust-gas turbine to drive a supercharger  at high altitudes
is an effective method of maintaining sea level engine power at altitude.
Analysis has shown, however, that the waste energy of exhaust gases is
recovered more effectively by maintaining an engine exhaust pressure higher
 than the minimum required for turbo supercharging and thus increasing the
work output of the exhaust-gas turbine. The extra turbine power beyond that
required for supercharging Can be supplied to the engine crankshaft through
 suitable gearing (compound operation).

The purpose of the analysis reported is to determine the improvement in net
brake specific fuel consumption that can be obtained if an engine is equipped
with a geared turbine and supercharger as compared with the engine using a
standard turbo supercharger. The calculated values specific fuel consumption
presented for an engine-turbine combination were based on NACA test data
obtained on an 18-cylinder radial engine. Operating conditions for which the
brake specific fuel consumption of the combination is a minimum are given.
The required turbine-nozzle area is also calculated to indicate the size of
turbine suitable for geared operation.

Because the engine, the turbine, and the supercharger have different
characteristics, elements designed to give maximum efficiency at some
operating conditions are incorrectly matched at other conditions. Provision
 must therefore be made to obtain satisfactory performance over the entire
operating range. The problem of obtaining a wide operating range is briefly
discussed.

The investigation reported was conducted at the NACA Cleveland Laboratory
in the fall of 1944.

-------------------------------------------------------
First the rotary is a very mechanically robust engine that tolerates high boost
pressures. The Achilles heel of this technique proved over time to be the
failure of the piston engine exhaust valves when the exhaust gas pressure was 25%
higher than the intake pressure.

Guess what? The rotary has no exhaust valve. 

The full 9 page report is obtainable from:
http://naca.larc.nasa.gov/
In pdf form.


MORE HISTORY

The worlds record prior to the Rutan Voyager for un-refueled distance was
held by a P2V that flew from Australia to Ohio. That airplane used the CW R3350
turbo compound which had a BSFC of 0.38. Super G Connies with this engine
were able to fly non-stop LA to London over the pole in the 1950's. 



I highly recommend the book "Lockheed Constellation" by Stringfellow &
Bowers Motorbooks ISBN 0-87938-379-8 Therein the TWA nineteen hour non-stop
flights from LA to London and twenty three hours, nineteen minute flights
London to San Francisco are described.

BUILDING A TURBO COMPOUND
I had an idea on how to implement a turbo compound arrangement using a gear
box out of a Paxton Centrifugal supercharger. The HP, gear reduction and RPM
is about right for hooking a turbine and feeding the power back into the
engine instead of removing it. Hopefully we will get 20% more power with no
more fuel and no additional load on the engine cooling system. 

The rotary has a lot of waste energy in the exhaust that could be put to
good use. Perhaps some additional air could be pumped into the exhaust
system before the turbine to burn the waste hydro carbons. The fact of the
matter is you can get more energy out of the exhaust than you really need
for supercharging. That is why the BSFC goes down on a turbo compound as
opposed to merely just turbo-charging.

This is sort of an exponential effect so the real HP limit is the detonation
and structural strength of the core engine. And here is where the rotary
engine scores big time.  The structural strength to weight ratio is
exceptional.  I also suspect the otherwise bad surface to volume ratio of
the rotary combustion chamber is an asset at high boost levels.

The thing to remember is there is always as much or more potential HP in the
exhaust as there is available from the output shaft. The more you pump it up
the more HP is available to pump it up. Since you don't need all the HP in
the exhaust for supercharging the sky appears to be the limit. This excess
exhaust HP fed back into the shaft will result in better and better BSFC.
The beauty of this HP is it does not add to the thermal load on the engine.

The big question is; how much can you get and for how long before the engine
starts coming apart? I would monitor the metal content in the oil, the
rotor housing metal and turbine inlet temperature very very carefully. I
would not rely on coolant temperature alone. Perhaps use a bore scope from
time to time to look into the housing and see if the oil is coking on the
surface of the housing. The other ting I would do is find a knock sensor
that would work.

My compound setup for the rotary would use one Inconel blow down turbine
feeding power into the eccentric shaft and an optional centrifugal blower
using modern aerodynamics either from a turbocharger impeller, an off the
shelf gear driven supercharger (there are several on the market) or a late
model gear or ball driven Paxton taking energy out of the eccentric shaft
to supercharge the engine. To get the full altitude benefit you would have
to fabricate a variable speed drive for the centrifugal supercharger as
well.

We will start with just a one speed blower with a gear ratio that peaks the
boost to what the engine will stand at sea level and at an e-shaft RPM of
6000. That e-shaft RPM assumes you are using a PSRU with a 2.2:1 ratio.

ATI manufactures a centrifugal supercharger the gearbox of which is a
candidate for my turbo compound scheme. They also have some nice looking
water to air heat exchangers if someone wants to go that route for their
inter-cooled turbo rotary aircraft engine.

If you just want to fly without a supercharger and you can live with 20%
more power and a 20% lower BSFC at that power at sea level you can forget
the supercharger and the inter-cooler and go with just the blow down turbine.

VARIABLE SPEED EVERYTHING
The full wammy is variable ratio gear supercharger with inter-cooler for
altitude and variable ratio geared blow down turbine for a lower BSFC. This
is several steps above the 20% more efficient 1950's R3350TC by the way, as
it only had a two speed centrifugal blower (no inter-cooler) and a fixed gear
ratio blow down turbine. A variable ratio drive can be made from a wide V
belt and movable flange pulleys controlled by a linear electric servo and a
computer

Now... if you just want to supercharge, a turbocharger with inter-cooler is
the best way to go as no HP is extracted from the eccentric shaft to drive
the supercharger.


ROOTS BLOWER TYPE TURBO COMPOUND
We also discussed a roots blower and a turbocharger and an inter-cooler
blowing air through the roots. As Jeff pointed out he felt the roots would
be horribly inefficient as an air motor feeding energy back into the
eccentric shaft. (We solved the problems of its not working at all by under
gearing or pop off valves) I am not sure I agree with Jeff but I am not
going to spend the money to find out.

A real  draw back to the roots as an air motor is its size and weight as it
operates at close to eccentric shaft speed and is therefor big and heavy.
Another real drawback is; it is a third device to suck power in the form of
its efficiency and is therefor in the, eff.A X eff.B X eff.C = total eff.
chain.

 A is the eff. of the turbine. 
 B is the eff. of the centrifugal blower 
 C is the eff. of the roots as an air motor.

This remains however as the simplest and easiest turbo compound engine to
build as all parts are off the shelf.



Paul Lamar



The power recovery heat balance chart .
much energy
was wasted by the exhaust valves in a piston engine turbo compounds.
THE WANKEL ROTARY HAS NO EXHAUST VALVES!!!. 
evidence we will eventually get more than a 20%
efficiency improvement with a turbo compound rotary.

look at the heat balance chart with out the exhaust valves.
Total heat available to the turbine now over doubles to
34.7% from 14.9%. The losses to gears and bearings also doubles
to say 3%. Windage and cooling loss goes to 3.2% from 1.6% and
aero and thermal losses got to 12% from 6%. Total loss percentage
is then 18.2%. 34.7% kinetic energy available for recovery
minus 18.2% losses is 16.5%! Up from only 6% with exhaust valves.

Total fuel energy burned in a 200 HP rotary is about 760 HP worth.
With exhaust valves you would have only about 6% or
45.6 HP available for the turbine.

Without exhaust valves you would have about 16.5% or 125 HP!!!!
Almost three times the HP available to drive the turbine!!! No wonder
you can boost a 13B rotary to 800 HP!! There is lots of kinetic HP to
be had in the rotary engine exhaust. Much, MUCH more than I had at
first thought. We always knew there was a lot of waste heat in
the rotary exhaust. Up to 50% of the total heat. What we did not
know up until now was what we could expect in terms of kinetic energy.

Chart "R3350TC-take-off-heat-balance". Out of a gross total of 3750 HP
the supercharger was consuming 385 HP. Subtracting 470 HP mechanical losses
from the gross total gave us 3630 net HP to the prop. Now look over on the lower
right side on the chart. The basic engine was 2750 HP sans turbines. Same as the
B29 engine.  All three turbines generated the takeoff HP increase or 880 HP. Divide
by three to get individual turbine HP's and you get 293 HP per turbine for this
R3350TC engine version.

Overall efficiency with a 10:1 air fuel ratio for take off was 17% without
turbo compounds and 22.3% with the turbines. Or an overall engine efficiency
gain of 5.3 percent at high power. Now the sensible power going to the turbines
is with the huge losses to the exhaust valves. About THREE TIMES AS MUCH will
be going to the turbines WITHOUT the exhaust valve losses. Chart three. "R3350TC Power
recovery heat balance." 

The high level of kinetic energy in the Mazda Wankel rotary engine exhaust 
has been  for 30 years.
 Anybody that has been around a Mazda rotary powered race car
without a muffler can understand the tremendous kinetic energy in the exhaust.

It was not until I read that SAE paper on the R3350 TC that I could put
a number on it. It then hit me like a supersonic shock wave. Yes of
course it has plenty of kinetic energy in the exhaust.


the Wankel rotary as an ideal gas generator for a turbine
engine.  

We are now building a traction drive device to extract the excess HP from
a stock turbo charger. Input speed RPM can be up to 100,000 RPM and output
RPM will be one tenth of that. The power from the traction drive output shaft 
will be transfered to the e-shaft of the rotary by a multi v belt to absorb
the torsional vibrations from the rotary engine. We hope to recover at least
50 HP from the waste heat in the rotary exhaust improving the BSFC from
the current .47 to .38 at cruise altitude. The range of any airplane using
this engine will increase by 25%. We hope to test the engine soon on a dyno


References

1954 SAE Transactions. Development of the R3350 Turbo
Compound Engine. 

Stratified Charge Rotary Engine Critical Technology Enablement Volume II 
NASA Contractor Report 189106
APPENDIX C DATE 10/04/91
Turboaachinery Systea Analysis For stratified Charqe Rotary Engine.
Sunstrand Aerospace



C.E. Irion and R.E. Mount
Rotary Power International, Inc.
Wood-Ridge, New Jersey