Paul,
I agree with you that the numbers given in the article are
ridiculous. I
also agree with your approach to solving for the fuel flow.
However, to be completely precise one piece of information is
missing:
the exact amount of power required to push the RV8 through the
air at
the speed in question. You assumed in your example that it is
180hp, but
I suspect this amy be a little high.
We know that in level flight thrust equals drag, so we can
solve for the
amount of power required if we know the amount of drag at the
speed we
are talking about.
However, I wasn't able to find a drag curve of the RV8 (Drag
Polar). I
did find one for the RV6, but don't know how reliable it is.
We can use these numbers from the graph for the RV6 and see
what we come
up with. We will use the formula for thrust horsepower:
THP = Drag x Velocity,
where Drag is in pounds and Velocity is in feet per second.
Therefore:
THP = D x (KTAS x6080/60) / 550
Since horsepower is defined as 33,000 lb.ft./min, this equals 550
lb.ft/second or 325.7 lb. x kt.
This simplifies to THP = D x V / 325.7
From the graph for the RV6 we see that a speed of 180 kt.
gives a drag
of about 200 pounds. So the power required is: 200 x 180 / 325.7 =
110 hp.
At a SFC of .47 that would give a fuel burn in pounds per hour
of 51.9,
or 8.65 gallons per hour. (I have to comment here that this
seems like
a very low fuel burn for 180 knots. I found this graph on a
webpage that
attributed it to a CAFE report in a 1993 issue of Sport Aviation).
http://www.eaa1000.av.org/technicl/perfspds/perfspds.htm
In any case, even if the chart is correct and an RV6 makes only
200 lb.
of drag at 180 kt., the above thrust horsepower calculation
does not
take into effect propeller efficiency. This is where I believe
the big
discrepancy is and how the test was tilted to favor the Lycoming.
Like any wing, the propeller will have a certain angle of attack at
which it is most efficient. Since the angle of attack of a prop
depends
on prop rpm, TAS, and diameter, prop efficiency will vary
according to
the ratio of these factors.
The ratio: Velocity / rpm x diameter is the Advance Ratio:
J = V/nD
where J is the advance ratio, V is velocity in KTAS and D is prop
diameter. The most efficient J depends on the prop blade angle.
Course
props (large blade angles) will be more efficient at larger advance
ratios. Fine pitch props will be more efficient at small
advance ratios.
That is why the rotary was at a disadvantage in the test, which
required
the same cruise speed AND the same prop rpm. With its greater
power the
rotary was most efficient with its prop working at a course
angle and
lower rpm. But because the test stipulated that the plane had
to be
flown in the way that was most advantageous to the Lycoming, it
skews
the results.
Another thing is the greater pumping losses from the engine at the
higher rpm. Even at the same MAP setting, running the engine at
higher
rpm will use more fuel.
The end result is that this "scientific test" is complete
horseshit that
was obviously planned carefully in advance to give a tilted
outcome.
This is just cheating, nothing else.
Regards,
Gordon.
Power required = Drag x True Airspeed / 325.7
Power required is also known as Thrust Horsepower
-----------------------------------------------------
Paul,
In my previous message I forgot one crucial step, to convert
from thrust
horsepower to brake horsepower before solving for fuel flow.
In the example using the drag number of 200 lb. at 180 kt. for
the RV6
we found that it takes 110 THP to move it through the air in level,
steady flight.
To find BHP we need to correct for prop efficiency, Neta, which is
THP / BHP.
If we assume a typical prop efficiency of 85 percent, we get
129 BHP
from the 110 THP we started with.
At an SFC of .47, this works out to a fuel flow of 60.6 pounds or
10.1gph, still very impressive for 180 knots true airspeed. I
think that
drag chart for the RV6 is a little optimistic (published in Sport
Aviation, so take obligatory grain of salt).
Just to further check this, I found a CAFE report on the RV8,
which gave
a fuel flow of 13.9 gph at 191 KTAS.
Assuming an SFC of .47, we can calculate the thrust horsepower:
SFC = FF / THP
Therefore,
THP = SFC / FF = .47 / (13.9 x 6) = 177.4
Now we can figure out how high the prop efficiency is since we
know the
engine is 200 BHP.
Since Neta = THP / BHP, we get:
177.4 / 200 = .88
This is pretty good prop efficiency, or maybe the Lycoming IO-200
angle-valve in the VAN's prototype RV8 that was the subject of
the CAFE
test was hopped up a little and putting out more than 200 hp.
We can also solve for drag, since:
FF = SFC x THP = SFC x D x V / 325.7
We can restate that equation to solve for drag:
D = (FF / SFC) x 325.7 / V, which is the same as:
D = THP x 325.7 / V
So we get:
D = 177.4 x 325.7 / 191 = 302.5
That's the drag of the RV8 at 191 KTAS, 302.5 pounds.
This is 100 pounds more than the graph I found for the RV6 at
180 KTAS,
which was also a CAFE report published in Sport Aviation. It
seems to me
that this confirms that the RV6 graph is a little optimistic.
In any case, the thing to remember is the prop efficiency,
which has a
huge effect on fuel consumption. The attached graph for a
McCauley 7557
prop as used on some C-172s shows the correlation between prop
efficiency and advance ratio.
Notice that the prop reaches a peak efficiency of just over 80
percent
at an advance ratio of .7. And notice how the efficiency
plummets as
advance ratio decreases -- at an advance ratio of .2 the prop
efficiency
is below 40 percent.
Remember that advance ratio, J, is Velocity divided by rpm times
diameter, J = V / nD
As n (rpm) increases, the ratio decreases. As the ratio
decreases, prop
efficiency nosedives.
Van knew exactly what he was doing when he set up this test. By
forcing
the rotary to fly at the same speed AND rpm as the Lycoming
ship, he
knew the rotary would be running at a lower prop advance ratio
and lower
prop efficiency.
This test was conceived very cleverly so the bigger engine and
prop on
the rotary would be giving up a lot of prop efficiency.
This is simply a dirty trick and lousy cheating, nothing more.
Of course
this is what you get when you have a magazine that let's its
advertisers
write stories. Shame all around.
Regards,
Gordon.
--------------------------------------------------
Hi Gordon,
The Vans article and chart says fuel burned for 160 N miles!
It did not say fuel burned per hour. It did not specifically
say at what speed HP or RPM the test was run at. It did say
8500 feet. Ray Richardson gave us the other numbers from
info he had.
According to google it is 87 miles to Eugene from Aurora.
Round trip would then be 174 miles.
On 7 gallons that would be 25 MPG for the rotary.
On 5 gallons that would be 35 MPG for the Lycoming
I doubt seriously you could fly an RV8 at any speed
HP or altitude with any prop that would yield 35 MPG.
If that were the case max range for an RV8 with 42 gallons
would then be 1470 Miles!!!!!! That is 50% greater
than any GA airplane I can think of or find.
BTW I would love to have any rotary powered airplane
that got 25 MPG or a max range of 1050 miles.
That is much much better than my C182 that gets
13 MPG with twice the tankage (84 gallons) and about
the same max range.
Here is an RV8 performance chart from:
http://www.pilotfriend.com/experimental/acft7/37.htm
Paul Lamar
I was going by the info that Ray gave: 150 kts and 2500 rpm.
I assumed the 150 knots was indicated airspeed, which at 8500 feet on a
standard day would give TAS of about 178 kt. I assumed this because it
does not make sense that a 200 hp RV8 would need 2500 rpm to reach 150
KTAS at 8500 MSL. This would be only 128 knots indicated at 8500 feet,
which the RV8 could probably do at 2000 rpm.
That's why I was using 180 knots true airspeed in the calculations. The
point was to show what fuel burn we could expect from an RV8 using a Lyc
IO-360 200hp, using known values for drag of an RV8. Obviously the fuel
burn I showed in the calculations is far greater than that shown in the
chart.
Quite obviously the chart in the article is, at the very least, very
confusing, or an outright mistake.
But if the test was run at 150 knots true, let's see where that leaves
us. Using the RV6 drag curve would give us a drag of 170 pounds at that
speed. That means power required would be: 170 x 150 / 325.7 = 78 thrust
horsepower.
At a prop efficiency of 85 percent that would give us BHP of 92. At a
SFC of .47 that gives fuel flow of 43 pph, or 7.2 gph. This is the fuel
flow an RV6 with a Lyc would do at 150 kt. true at 8500 feet, so the RV8
is probably not that far from that. (Assuming again the CAFE graph for
the RV6 is correct.)
So for the 160 nm trip in the article, it would surely take more than an
hour's worth of fuel, depending on wind conditions. So that chart still
doesn't make sense.
It's obvious that EAA needs to print a clarification and correction
that
will explain all this. They should also print a full disclosure about
the author being an employee of an advertiser and how that advertiser
was given the prerogative to arrange the conditions for the "test."
This
is a journalism ethics issue.
The clarification should also explain that the conditions chosen by the
EAA advertiser (Van's) produced a tilted playing field against the
rotary, in terms of fuel consumption, due to prop inefficiency at a
higher than optimal cruise rpm. In order for the test to be fair, the
planes should have flown at the same speed and distance, but allowed to
adjust rpm to provide optimum efficiency for each respective ship. Only
then could the test be said to be fair.
If we take an auto analogy where we want to compare fuel mileage between
two cars, do we insist that one of them cruises down the highway in 3'rd
gear, while the other one is in overdrive? This is exactly the case
with
the rotary ship that had to flatten its prop to bring cruise rpm up to
2500 -- it's like cruising in a lower gear.
To be really fair, the magazine should revisit this issue in a future
article, with a test set up completely fairly and which will let each
plane perform to its maximum capability in all measured criteria.
Regards,
Gordon.
-------------------------------------------------
Lets simplify things. 180 SM at 180 MPH or
or 1 hours. So the fuel burn is roughly 1 times the
numbers in the chart? Let's say 7 gallons an hour for the
rotary and 5 gallons and hour for the Lycoming. I don't think
so at 180 MPH.
Lets say they did it at 120 MPH or 1.5 hours.
So the chart is not total fuel burned as stated in
the chart but the fuel burned per hour. So the rotary
burned 10.5 gallons total and the Lyc burned 7.5 gallons
total at 120 MPH? Perhaps.
Lets assume this was true and the chart was GPH.
Lets say they both generated 100 HP doing it.
BSFC for the rotary 42 pounds/divided by 100
or a BSFC of .42. Wow! Nice but I don't think so.
BSFC for the Lyc 30/100 = .3 double wow! No
way in h***.
No combination of speeds makes any sense what
so ever out of what was actually stated in this article
and in the chart.
Taking the chart at face value the fact of the matter
is no way is the Lyc going to get there at 38 MPG nor
will the rotary get there at 27 MPG.
Paul Lamar
--------------------------------------------------------
I didn't see that anyone here looked up how far it actually is between
EUG and UAO - it's 70nm each way, 140nm total (161sm).
The section of the chart relevant to this discussion says the Lyc's
burned an average of 5.25gal over the 140nm for 26.67nm/gal, or
30.67sm/gal. The rotary powered airplanes burned an average of 7.475gal
for 18.73nm/gal or 21.53sm/gal.
I couldn't find any reference in the article to the speed flown for the
cruise portion of the test..
It's widely accepted that a 180hp Lyc O360 at 75% power will burn
10-10.5gal/hr. 75% of 180hp is 135hp. If the BSFC is 0.47, that works
out pretty close..
From Van's website, the RV8 with 180hp, 75% cruise is 204mph (or 177KTAS).
Doing the math here says the fuel economy at 75% is 19.9sm/gal
(17.3nm/gal). So clearly they weren't running 75% cruise settings.
The Van's site also lists 55% power cruise speed as 182mph (158KTAS).
Fuel flow at 55% should be around 7.75gal/hr (assuming the same
BSFC=.47). That would give 55% fuel economy = 23.5sm/gal
(20.42nm/gal). Hmm. So they must have been really loafing.
Digging around, I found the previously mentioned mentioned CAFE report
for the RV8A - essentially the same airplane as "Tweety" from the SA
article:
http://cafefoundation.org/v1/aprs/RV-8A%20APR.pdf
Their chart (page 8/12) bottoms out at 182mph (the 55% power speed) and
25sm/gal, 7.2gal/hr. Hmm. Looks like the Van's published numbers are a
bit conservative.
One thing that's interesting about the CAFE scorecard is that on the
12000' DA test chart, the fuel economy actually starts to get worse when
slowed from a fuel flow of 6.7gph to 6.0gph. Probably two factors here
- worse efficiency due to pumping losses from lowered manifold pressure,
and possibly higher induced drag from flying so slowly at altitude
(though TAS=180, IAS=145, which is hardly slow).
Going back to the 8000' DA chart, if we assume that we can extrapolate
out to slower airspeeds (ignoring the above paragraph), and we wanted
31sm/gal, we'd have to go down to a fuel flow of about 5.7gal/hr, and
TAS=172mph (IAS~=148mph). Not totally unreasonable when eyeballing the
chart. Would have to set a very low cruise RPM to not suffer pumping
losses.
Flying so slowly definitely favors these Lycomings against those
Powersports - one of the Lyc's has manual mixture control, which should
allow it to run quite a bit better fuel flow.
It would be interesting to know what power setting everybody typically
uses on RV8s. I know that I usually run much less than 75% in my 182 -
WOT above 6000 MSL, 2300RPM (cause it's quieter, and cheaper).
Regards,
Matt-
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.