Turbo compound Wankel rotary engine. Paul Lamar Rotary Engine Newsletter Santa Paula California rotaryeng@earthlink.net www.rotaryeng.net TURBO COMPOUNDING THE ROTARY A turbo-compound engine collects all of the exhaust gasses and runs them through a turbine, with all of the power generated going back into the crankshaft and ultimately to the propeller thereby recovering some of the waste heat in the exhaust. Ref 1. 1954 SAE Transactions. Development of the R3350 Turbo Compound Engine. Besides the economic advantage of turbo compounding an engine there are other consideration. Short range also cuts into long trip times and limits your weather options making the airplane less safe. Having the range to turn back has saved my life more than once when on a long cross country's over remote areas of Canada, Alaska and Baja. A high performance airplane with a small thin wing has a limited volume for fuel. Such air cooled piston engine airplanes may need to stop every 400 or 500 miles for fuel. Turbo compounding also improves the power to weight ratio of an engine by roughly 20%. Ref 1. Allison built a V12 turbo compound engine during World War II in an attempt to recover some of the waste energy resulted in a turbo-compound configuration. Ref 2 It was identified as the V1710-E22. Work began in 1944 and continued until 1946. It was sponsored by the US government but canceled with the advent of the turbine engine. Apparently it was the first turbo-compound engine. The V1710-E22 had a military rating of 2320 hp, and a War Emergency Rating with water/alcohol injection of 3090 hp. With a compression ratio of 6:1 it achieved a 19% improvment in the BSFC. It never flew. The normal supercharged Allison V12 generated 2000 take off HP and 2500 HP War Emergency Rating. Ref 2 Vee's For Victory by Daniel D. Whitney. Schiffer Miltary History 1998 ISBN 0-7643-0561-1 The most widely used turbo-compound engine was a version of the air-cooled, 18-cylinder, two-row radial Curtiss Wright R3350-TC. Ref (1) Used in many airliners and several miltary aircraft. Thousands were built. This engine had three turbines, each fed by 6 cylinders, that were geared to the crankshaft. The normal supercharged version produced 2700 hp and weighed 2850 lbs. The BSFC was as low as .37 at sea level and .33 at 30,000 feet with a compression ratio of 7.2:1. The turbo-compounded version produced 3500 hp and weighed 3440 lb resulting in a power to weight ratio of over unity. The worlds record prior to the Rutan Voyager for un-refueled distance was held by a P2V that flew from Australia to Ohio. Super G Lockheed Constelations with this engine were able to fly non-stop LA to London over the pole in the 1950's. Ref 1a. "Lockheed Constellation" by Stringfellow & Bowers Motorbooks ISBN 0-87938-379 The Achilles heel of this engine proved over time to be the failure of the exhaust valves when the exhaust gas pressure was 25% higher than the intake pressure. Much of the developement effort was expending on improvements in exhaust valve durabilty. Another protoype turbo-compound engine is the Napier Nomad, which was built in England. It was a 12-cylinder, horizontally opposed, liquid cooled, valve-less, 2-stroke cycle Diesel engine with a 3-stage turbine. It reached flight test but not production. BSFC was .345 (shaft HP) at 11,000 feet and a compression ratio of 8.25. Ref 3 Ref 3 A history of Aircraft Piston Engines by Herchel Smith Sunflower University Press Corrected editon 1986 ISBN 0-89745-079-5 NACA sponsored several reports on turbo compound engines. One of which used a dynamometer data to gather data. This test program indicated a BSFC of .323 at 10,000 feet. 14% better at 10,000 feet and 21% better at 30,000 feet. Ref 4 NACA REPORT No. 822 1944 CALCULATIONS OF ECONOMY OF 18-CYLINDER RADIAL AIRCRAFT ENGINE WITH EXHAUST-GAS TURBINE GEARED TO THE CRANKSHAFT By RICHARD W. HANNUM and RICARD H. ZIMMERMAN The Wankel rotary engine is a very mechanically robust engine that tolerates high boost pressures. There are no cyclical reversing stresses in the three major moving parts that lead to fatique failure in the light weight piston engine. Consequently the power to weight ratio of the current Mazda RX8 Wankel rotary engine is comparable to an air cooled aircraft engine at 240 HP and 190 pounds less the weight of the required PSRU. The compression ratio is enherently low limited to about 10:1 due the neccesitty of locating the combustion chamber in the rotor. The combustion chamber surface to volume ratio is high affecting the efficiecny of combustion but adding to the ability of the engine to survive high power to displacement ratios. The Wankel rotary has no exhaust valves. Porting is done by the rotor as it orbits the inside of the rotor housing. The Wankel rotary has approxmately three times the net available kenetic energy in the exhaust as compared to a piston engine. Two thirds of the total kinetic energy in the exhaust of a pistone engine is disapated by the exhaust valves. Ref 1 The high level of kinetic energy in the Mazda Wankel rotary engine exhaust has been known for 30 years. Anybody that has been present at race where a Mazda Wankel rotary powered race car operated a muffler can appreicate the tremendous kinetic energy in the exhaust. There is always as much or more potential HP in the exhaust as there is available from the output shaft. (Ref 6) The more you boost it the more HP is available to boost it. This is an exponential effect so the real HP limit is detonation, durability and structural strength of the core engine. Turbo charged Mazda 2.6 liter two rotor engines have been boosted to 800 HP for racing purposes using alcahol and nitrous oxide. The Wankel rotary appears to be an ideal gas generator for a turbine engine. Ref 6 Rotary Engine. by Kenichi Yamamoto. Sankaido Company Ltd. 1981 In English. No ISBN number. BUILDING A TURBO COMPOUND WANKEL ROTARY ENGINE. I had an idea on how to implement a turbo compound arrangement using a ball traction drive gear box from a Paxton Centrifugal supercharger. The HP, gear reduction and RPM is about right for connection a turbine and feeding the power back into the engine instead of removing it. Hopefully we will get 20% more power with no more fuel and no additional load on the engine cooling system. My compound setup for the rotary would use one turbo charger turbine feeding power into the eccentric shaft and an turbo charger centrifugal blower using modern aerodynamics from a stock Mazda turbocharger. We will start with a turbine reduction gear ratio that peaks the torque feed back to what the engine will tolerate at sea level and at an e-shaft RPM of 7500. That e-shaft RPM assumes you are using a PSRU with a 2.85:1 reduction ratio and a maximum prop RPM of 2630. The historical evidence suggest we will eventually get more than a 20% efficiency improvement with a turbo compound rotary. We are now building a traction drive device to extract the excess HP from a stock turbo charger. Input speed RPM can be up to 100,000 RPM and output RPM will be one tenth of that. The power from the traction drive output shaft will be transfered to the e-shaft of the rotary by a V-Ribbed belt to absorb the torsional vibrations from the rotary engine. We hope to recover at least 50 HP from the waste heat in the rotary exhaust improving the BSFC from the current .47 to .38 at cruise altitude. The range of any airplane using this engine will increase by 25%. We hope to test the engine soon on a dyno Stratified Charge Rotary Engine Critical Technology Enablement Volume II NASA Contractor Report 189106 APPENDIX C DATE 10/04/91 Turboaachinery Systea Analysis For stratified Charqe Rotary Engine. Sunstrand Aerospace C.E. Irion and R.E. Mount Rotary Power International, Inc. Wood-Ridge, New Jersey