Does the Australian Renesis four port come with the automatic TX
flywheel and counterweight? Do you have the same engine if you P-port
the four and the six port ? If you do than the four port should be the
choice because Mazdatrix wants $455.00 for the automatic
flywheel/counterweight combination. H. Karibian
Yes I think so.
Yes you would have the same engine. As far as I know there are
no other changes. I could be wrong.
Paul Lamar ...No rotor no motor.
As far as i know the Australian Renesis engine is brand new out of the
box,redrive fitted, cooling systems fitted,then fine tuned. I live about
an hours drive from where these engines are installed into Cobra
aircraft. The airport where i live is where these engines are tested and
flown, they run and sound beautiful.
Go to
www.tomair.com.au <http://www.tomair.com.au> then forum,then
Barry Mayne and his arrow. There you will find photos of the installation
of the engine.
If you want to know more about this engine E- Mail Tom .
Ray
First flight:
"G'day everyone,
Yep, finally got to do it.
I scared the crap out of myself as everything happed so quick.
I can't give any figures as I was too busy trying to save my arse,
if there had been any buttons on the seat cushions the pucker factor
would have neatly plucked them off.
Ground roll was good, but before I could see what the speed was it
lifted off and went almost vertical. I managed to catch it before
it stalled but it continued to porpoise badly, then the engine
started running rough. By this time i was at the boundary fence
and I picked out the paddock to crash in. It was still climbing
and the porpoising reduced so I continued with the circuit. On
downwind the engine smoothed out a lot and it was stable. It was
good enough for me to take a pic out the front. I had no idea
whether the porpoising would return when setting up on final and
was resigned to a probable crash landing. It didn't happen, it
behaved in a very stable manner all the way down and onto the
ground for ( what the CFI called ) a smooth landing.
The knees were like jelly and I thought that maybe I needed to
change my jocks but on reflection most of the problems were of
my own making. Firstly I have no idea of the take off speed, I
was too busy looking down the runway keeping it straight.
Secondly I think I had too fine a pitch setting and the rough
running was due to little or no load on the engine. Thirdly I
had been agonizing about doing the first flight for so long that
I was a nervous nelly.
The good aspect of the flight was that it was very stable in roll.
The controls are heavier than I thought they would be and the pitch
is way too sensitive.
I'm sure everything can be sorted out, after all thats what
the 40 hours testing time is for.
More later as I think of it
Cheers
a very relieved Baz"
Second flight:
"Well, the weather was absolute crap here over the weekend but
all the rain was great.
In between showers yesterday I did another run ( cloud base
around 1500' AGL ).
Very dissapointing to say the least. Changing the AOA on
the groung certainly got rid of the vertical attitude of
the first flight but needed a pull back on the stick to
get it off the ground, after lift off it still porpoised a lot.
Setting the prop with more bite helped with speed but the
faster it went the more unstable it became in pitch. The
engine still giving the impression that it is over running,
maybe I still don't have enough pitch on the prop, I just don't
know. I throttled back to run at about 4600rpm on down wind
with TAS 110 knots and the engine giving the odd rough running.
Not at all impressed I gotta tell ya. Pitch, while controllable
was very erratic and I was glad to get back on the ground and said
a few choice words to the bird. After landing I ran it up to full
throttle and it didn't miss a beat. The only good thing I can report
about the flight is that the oil temp was in the high 70's and the
coolant in the low 80's.
There has to be a reason why its so unstable, maybe the C of G is
wrong , who knows, I sure as hell don't. It didn't try to kill me
this time so I guess thats a bonus.
I really thought it would be right this time and I could put
it up for sale before going to Oshkosh later this week but
I can't do that until I'm satisfied with it.
I will have to talk to Tom, but I will leave it until I get back.
Baz"
New aircraft design ... rotary engine....real balls :)
Cannot figure out the CG position on the ground relative to
the quarter cord point and is still willing to fly it? It is
a miracle that this guy is still alive :)
Paul Lamar
Old message on this subject.
-------------------------
Date: Tue, 13 Dec 2005 08:43:46 -0800
From: Rotary Engine
<rotaryeng@earthlink.net>
Subject: Rotary in Cobra aircraft
>
> >
> >> Hi
> >> Try this site,engine and redrive all new
> >> Regards Ray
> >>
http://www.tomair.com.au/
> >>
> >>
> >> These guys are in the early stage of development.
> >> Mostly hype and little substance. Some ridicules claims
> >> in the past. The web site is vague about a lot of things.
> >>
> >> So far their engineering leaves a lot to be desired.
> >> Attaching a two rotor to Hirth gear box is doomed to failure.
> >>
> >> I wish them well but I will keep my money firmly in my pocket
> >> for awhile and see what happens.
> >>
> >> Paul Lamar ...No rotor no motor.
> >
> >
> >
> > Paul,
> > I wish them all the best, and I don't like to see Aviation endeavors
> > fail,
> > especially if their Aussies, but I'm yet to see +ve outcomes. The last
> > I
> > heard they were having cooling problems - funny that!
> >
> > BTW their using your favorite flat plate mount.
> > I wondered what gearbox they were using, I did ask someone and all they
> > said
> > was they were off-set.
> > George ( down under)
>
>
> I've attached some pictures of the Cobra "Viper" engine and radiator
> installation in the Cobra "Arrow" aircraft. It looks like a spur gear
> drive. I could not find these pictures on their current web site. I
> don't remember where I acquired them. The web site says this aircraft
> crashed on landing; there was no mention of dates.
>
> Aubrey
>
> Looks like a plastic or wood mock up to me. Perhaps the metal
> looking parts have been scrounged from wherever.
> Could be a stock manual tx bell housing painted black.
> That is no SAE prop flange.
>
> Like the dozen or so other PSRU's I have seen depends on what
> the inside looks like.
>
> Paul Lamar ...No rotor no motor.
>
>
> ---------------------------------------
>
> I read with interest the thread about the rotary engine from cobra
> Aviation. The engine is far from a mock up and in fact has been in a
> test aircraft for some time. Unfortunately that aircraft came to grief
> on landing about a week ago ( no, not airframe or engine related ).
> Like all developments there has been teething troubles including cooling
> which have been addressed and I am sure there will be others to raise
> their heads but presently the engine is performing well. I also agree
> that in the early stages there were some ridiculous statements made but
> once cutting through the crap to the reality the performance including
> cooling has been good. The PSRU is from NZ and runs a 3 blade in flight
> adjustable 70" prop. the ECU is a Wolf 3D and individual Bosch coils
> supply the spark.
>
> As far as the engineering goes, I have seen some pretty ordinary
> fabrications on this site from time to time and this is as good as most.
> I am including a few pics of the engine on my project which I expect to
> have flying within 3 months time.
>
> Your site has been of great assistance to me by giving me a much greater
> understanding of the Rotary but I don't believe its fair to knock
> something just because it is different from what you do.
>
> Baz Mayne
>
> --------------------------------------------------
>
> I never said the engine was a mock up. I said the gear box "Looks like a
> plastic or wood mock up to me." The subject of the previous message
> was gear box.
>
> It is not because it is different. When the designer makes ridicules
> claims
> his engineering ability is immediately brought into question.
>
> Engineering and fabrications are two entirely different things.
> The welding and paint job on a poorly designed motor mount can be
> perfect but that does not make it a good or safe motor mount. The strut
> holding the lower end of the oil cooler is going to crack and fall off.
> An obvious example of incompetent engineering.
>
> From the looks of it the engine is too big and heavy for the airframe.
>
> Your cooling problems are just beginning despite the nice looking
> oil cooler. Have you tested that oil cooler to 300 psi?
>
> And of course the gear box is a total unknown.
>
> Why aren't you asking for help? It's free and nobody is twisting
> your arm to implement it.
>
> To be brutally frank I don't mind anybody killing themselves
> but I wish they would do it in something other than
> a rotary powered airplane.
>
> Paul Lamar
>
Hi Paul
I went to Melbourne to the Cobra factory before purchasing my RV7 kit. I was
impressed with the Cobra airframe but you are right that the Mazda engine is
far too big for it. Tom explained that the power would be held down to 135hp
but even so I predicted that cooling, under hood heat, and exhaust noise
would be major problems.
Ian Beadle Australia. Mounting engine tomorrow.
---------------------------------------------------------------
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.