Car AND Driver is my favorite car magazine. They are the
no spin guys. The Editor in Chief, Csaba Csere, is a former student
of mine. I only had him for a week 30 years ago but I like to think
I had a disproportionate influence on him. I could be way wrong .
We used to see more of each other but lately, since I got out of the
car testing equipment business, I don't see him much. It did run in
to him at the Tokyo Motor Show last year.
Recently C AND D did an article on diesel powered cars.
Mercedes think they have found a way to make diesel engines
meet the U.S. EPA draconian smog rules in regard to NOX.
One of the emissions problems that a lean burn engine
has, such as a diesel, is NOX. Mercedes has come up with a
possible solution.
The rotary, surprisingly, is also a lean burning engine and it
obtains its best BSFC at low power by running very lean. Something
on the order of twenty pounds of air to one pound of fuel
and at an EGT reading of 200 degrees F lean of peak. This is much
like a diesel.
IMHO and the opinion of Tracy Crook, who has a hundreds of hours
running the rotary lean, thinks this has to do with the rotating
combustion chamber. Tracy thinks, and I agree with him, the
centrifugal force on the fuel molecules, being heavier than
air, tend to congregate out near the spark plugs. You might
call this a form of stratified charge. Therefore the rotary
engine runs smoothly at lean mixtures the gas piston engine
can only dream about. If you have ever owned a gasoline engine
powered boat you know that gasoline vapors congregate in
the bottom of the boat called the bilge. Therefor they are
heavier than air. If you don't ventilate your bilge properly
your boat can blow up.
However the RX8 engine computer keeps the mixture at 14.7 pounds
of air to 1 pound of fuel AKA stoichiometric to minimize NOX
under all cruise conditions. Too rich for best BSFC. This
can be proved by connecting your note book computer to the
OBD II connector under the RX8 dash and recording the mixture
ratio in real time. This software and connector will work.
I use it my self.
http://www.autoenginuity.com/
The RX8 would get a lot better MPG during freeway cruise and around
town if the mixture were leaned out and other means of eliminating
the NOX were employed. The Mercedes method could be one of them.
Paul Lamar ...No rotor no motor.
BTW I forgot to mention the properly leaned rotary engine
powered aircraft obtain about 30 MPG at 150 MPH. Try that in
your RX8.
--
Paul Lamar ...No rotor no motor.
Paul, ET AL
I see that Auto Enginuity is selling several scanners on EBay for
$199.99. Try item 300018083590, or do a search for autoenginuity.
I assume this is the basic unit, not the one that lists for ~ $800.
Joel
The $200 price sounds like the cable/connector and software for your
lap top computer. That is about what I paid. The $800 price sounds
like a stand alone scanner as there are many others on the market.
Paul Lamar ...No rotor no motor.
Paul
Just talked to the Technical Support Center at Auotenginuity in Arizona.
They state that the software only supports 1996 cars and newer because that
is when OBD11 was required by the US Government. OBD11 replaced OBD1 and
every auto company could have whatever interface protocol they wanted before
1996. They required the OBD11 so they would not have to put sensors up the
tailpipe. He also commented that they have no plans for doing anything for
the older cars. It is a shame that I could not have their scan tool for my
1991 RX7. Any help here anyone?
Norm
Correct. Actually my 1994 Cougar had OBD II. BTW IMHO
OBD II was partially responsible for discontinuing the sales of
the 1994 and later RX7s in the U.S. because Mazda did not want
to spend the money to redo the computer. I think.
You might talk to
http://www.technosquareinc.com/mitelite.htm
and see what they have.
--
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.