Subject: More RX8 recall info?
From: Rotary Engine
Date: 9/1/2006, 2:01 AM
To: AA-me


> --------------------------------------------
> They don't mean oil 'leaking' out of the engine onto the ground, they
> mean
> oil blow by where by it, or rich fuel mixtures (also another issue) get
into
> the catalytic converter and mess it up. Because of a bunch of EPA regs
that
> had to be met before it's release in the USA, there were various
> modifications to make the mixture richer, and less oil to be pumped in by
> the MOP at low idle speeds... both were unfounded, and bad ideas turns
> out... Hot climates with cars sitting at low RPMS see less oil, and of
> course heat is the enemy. Plus, with mileage conscious 5W20 spec'd in,
> cooling is even worse. Additionally, a richened fuel mixture did not
> apparently cool cats down, so both of these items are being attended to
> by
> Mazda.... it's sounding like if your engine is still healthy after vacuum
> testing, you get the EEPROM fix to change the oil and fuel curve and you
are
> done. If it fails vacuum, you get a new or remanufactured engine with the
> new EEPROM fix all ready to go. The car will be better than before - so
> chill out, don't loose hope, and keep enjoying your RX-8.
> > Posted by: joe ancona | Aug 25, 2006 10:38:32 PM
> -----------------------------------------------------
> "Because of a bunch of EPA regs that
> had to be met before it's release in the USA, there were various
> modifications to make the mixture richer,"
> > That fact really pissed me off. If you start up the RX8 from
> cool (55 F) and let it warm up by idling  or slowly driving
> it around town  before getting on the freeway it really
> sucks down the fuel. You can mitigate this by getting on
> the freeway as soon as possible. My Honda Odyssey and Robin's
> PT Cruiser are also afflicted by this. The draconian wackos will
> sacrifice anything for a .000001 percent reduction in smog
> including billions of gallons of additional fuel burned world
> wide. Soon it will be illegal to fart.
> > Reading between the lines I think the vacuum test referred to
> above is done at top dead center with a special fitting for
> the spark plug hole. IMHO this checks the O-rings around
> the oil scrapers. Mazda uses some sort of O rings in those scrapers
> but I have no way of knowing what material they are made of.
> > I can tell you this. They are not as temperature resistant
> as they could be as we boiled some in oil. I drove my 1976 13B Cosmo
> for years with burned out oil O-rings and the smoke upon start up
> obscured the sun.
> > The best O-rings for this job are Creavey Teflon encapsulated
> silicone O-rings good to 500F. Teflon is inert to all known
> chemicals and silicone is good to 500 F.  I am always harping
> on these. Chuck Dunlap flew them for a couple of years with
> no problems.
> > http://www.creavey.com/
> > Paul Lamar ...No rotor no motor.

I forgot to add the clue about hot climates. No doubt
the oil is overheating.

Paul Lamar ...No rotor no motor.

More mis info.

http://www.autoblog.com/2006/08/24/mazda-to-recall-the-rx-8/

"Mazda claims that the problem is brought on by hot climates or
the usage of synthetic oil. If the oil is allowed into the
combustion chamber, it eventually reaches the catalytic
converter and causes a malfunction of that emissions-control device.

[Source: Rotary News]"

What do they mean "if"??  The RX8 engine sucks oil out of the
oil pan and injects it into the combustion chamber
of course the oil reaches the combustion chamber.

Don't let the dealer tell you they will not fix your engine
because you used synthetic oil. When I bought my RX8 I specifically
asked the dealer and the Mazda Japan PR person if they objected
to synthetic oil. They said no but they had not tested it.
The very large Japanese oil company Idemitsu manufactures and sells
synthetic Rotary Engine oil that is specifically formulated
for rotary engines.


Paul Lamar ...No rotor no motor.



There is a ultimate solution to the problem of injecting just enough  oil
for the apex seals and yet not too much to fowl the catalyst.

There is a gentlemen that lives in the Florida panhandle by the name of Richard
Sohn. <unicorn@gdsys.net>

Richard manufactures a device that blocks the oil supply
from the oil pan to the apex seal metering pump and allows the connection
of a separate tank holding two cycle oil. Two cycle oil burns cleanly.

You can then use the best oil for each job. Synthetic in the oil pan and
two cycle oil to lube the apex seals. Mazda should implement this idea as soon
as possible.

I also might add the rotary engine has an unequaled power to weight
ratio. Car weight tracks engine weight. This leads to a lighter car
that uses less natural resources. The RX8 is 500 pounds lighter in
weight than its competitors.

-- 
Paul Lamar ...No rotor no motor.

Here are some jpgs of the O-rings in question. They are scans
from the Jan Norbye book "The Wankel Engine".

I think the change from RX7 peripheral exhaust port to RX8 side exhaust
ports is partially to blame for this problem with the oil O-rings.
I suspect the RX8 rotor is now running hotter in the oil O-ring area.

The best Teflon encapsulated Silicone O-rings only cost a couple of dollars
each. Unfortunately the engine must be disassembled to replace these
O-rings. Unlike a lot of other O-ring material Teflon is totally
immune to synthetic oils. Teflon is also heat resistant to
800 F or 420 C.

For this engineering over site it will cost Mazda lots of money.
Needless to say it would have been cheaper to install them
in the first place.

Mazda could also attempt to develop a synthetic  oil that burns
cleanly. It might just be easier to use two separate oil supplys
as mentioned above. An easy here and now solution.

Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.