Subject: P-port leak
From: Rotary Engine
Date: 9/16/2006, 3:57 AM
To: AA-me



        No doubt about it. The P-port is leaking.
        I machined a sleeve out of PVC pipe 1.875 inch  diameter
        and slipped it into the p-port. Sure enough the sound
        stopped. Pull it out a couple of tenths and the sound
        starts again.

        I also found a tiny, tiny leak around the repair on the
        cracked rear rotor housing. Pumping the engine water jacket
        up to 50 psi with my compressor does wonders in the leak
        detection department.

        I borrowed a vacuum pump from my next door neighbor that
        repairs HIVAC stuff. I then pulled a continuous vacuum on
        the water jacket. Don't forget to take the schrader valve
        out of the pressure fitting.

        I cleaned around the tiny tiny leak
        with a small round file and acetone and applied a little more
   JB Weld.
        I left the vac pump sucking. Hopefully the vac pump will suck the
        JB Weld into the crack. We will see tomorrow if this works.
        I will pump up the water jacket to 50 psi tomorrow and
        see if the tiny tiny leak is gone. This can be repeated if
        necessary.

        If it works I will do the same thing to the p-port leak.

        By all means folks pressurize those p-ports before you assemble
        the engine. Much easier to fix before the engine is all put
   together.

        Also my neighbor loaned me some florescent soapy fluid
        which is great for detecting leaks.

        You might also be able to do this with a cheap hand vac
        pump you can buy in auto parts stores.

        Paul Lamar ...No rotor no motor.



   So the idea here is that the area that is leaking is the space between
   the end of the pport tube & the inner wall of the rotor chamber?  That
   would explain how coolant could get into the pport tube (where I found
   it) yet not flood the rotor housing.  For those who don't know, when
   installed in my aircraft, the engine is tilted about 1-degree toward the
   starboard side -- thus the pport does not sit horizontally, but ever so
   slightly "down hill" in that direction.  Thus, a slow leak as I was
   experiencing might very well allow the coolant to collect in the tube
   vs. rotor chamber.

   Am I correct in assuming that you could detect which side of the pport
   is leaking by milling back on some percentage of the end of that PVC
   tube?  Mark the parts of it that are full-depth & then insert it into
   the PPort and rotate through 360-degrees.   The noise will cease when
   the extended portion covers the leak & resume when the open portion is
   rotated over it.

   Probably not necessary to do it tho - logic dictates the problem must be
   on the flex-plate side, since the front-cover side is a void space
   between the 2 PPorts.  Might be an interesting exercise none-the-less.

   Didn't you take pix of the housings after you repotted with JBWeld?
   That would answer whether is was the JBweld side that was leaking, or
   the side with the original epoxy which appeared fully cured.

   Mark Supinski

   Correct Mark. You can notch the end of the PVC pipe and rotate
   it to find the exact location of the leak. A few drops of JB Weld
   will take care of it with the vacuum pump working.
   that pump pulls 29 inches of Hg no problem.

Paul Lamar ...No rotor no motor.

Yes it was leaking on the non JB Weld side. Big mistake
using that high temp epoxy I bought. I should have asked
Mazdatrix what they used for p-ports and they would have
told me JB Weld as they did later.

OK it worked great. It is like working on someones teeth however.
You need a small inspection mirror and a small pencil flash light
that will lie in the bottom of the tube. I glued a small
section of 1/4 inch  dowel about 3/16 long to a small wood tongue
depressor to apply the small gob of JB Weld to the leaking
area. The vac pump pulled in the JB Weld.


If you want belt and suspenders on
this Burns stainless has 321 SS 1.875" OD tubing with
a .035" wall. Cut the SS tubing just long enough to go
up to  where trochoid wear surface starts but not beyond.
Coat it with a very thin layer of JB Weld and insert it into the
aluminum tube. I have some inquires out for even thinner
wall SS tube. On the order of .015" to .020". I think I will
do this with Marks engine.

Best to just pressurize these tubes to 50 psi before you assemble
the engine to check for pin hole leaks.


BTW one advantage of the P-port is you can visually inspect
the trochoid wear surface with a flashlight and a small inspection
mirror in the compression chamber area.

Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.