Paul,
Here is some information from Tracy on the coil problem.
Ian
Coil/igniters are fairly critical on two things.
(1) Ambient temps around coils should be kept under 130 degrees when run
at constant high rpm operation. I enclose my coils and have a blast
tube blowing cool air into the enclosure to ensure this.
(2) Dwell time on coil needs to be correct. If possible, measure the
running dwell time on the coil (Pin A on RX8 coils, see instructions for
location). It should be close to 3 milliseconds. I can't remember the
details of your EC2 order but the Renesis version can be ordered with
one of two options, LS1 coils (5 millisecond dwell time) and RX-8 coils
(3 MS). If you have the wrong version the coils could run hot (LS1
running on RX-8 coils) or have weak spark (RX-8 running on LS1 coils).
Ah so. Very good. All makes sense. Jibes with what I measured
on the RX8 car coils. I.E. 2.5 milliseconds. I'll start mounting
coils inside the ram air ducting for the radiators in my 3D's :)
Simple fix.
Have you checked your dwell time yet Ian?
Paul Lamar ...No rotor no motor.
Yes 2.5ms.
I will send the cowl pictures soon.
Ian
I have come to the conclusion, after looking at the stock
RX8 computer PC board, the required power switching transistors
or FETs MUST be in the coils. Search as I might I cannot find
anything on the PC board that looks like a high current FET's or
power transistors used for driving four coils.
IMHO fuel injectors will soon have the power switch integrated into
the injector body as well.
Paul Lamar ...No rotor no motor.
Paul
What about the two transistors attached to the heat sink in the upper
left
of the board?
DougFir
I am not sure what they do. They might be the injector switch.
NEC B1453
2SB1453 PNP epitaxial silicon power transistor
For fast switching.
Functions PNP epitaxial silicon power transistor
Applications For fast switching
Features High DC amplification factor
hFE>=100(VCE=-5V, IC=-0.5A)
Full-mold package, easy mounting
Performances VCBO=-60V, VCEO=-60V, VEBO=-7.0V
Ic(DC)=-3A, PT=25W(Tc=25deg.C)
PT=2.0W(Ta=25deg.C)
hFE=100 to 400(VCE=-5V, Ic=-0.5A)
VCE(sat)<=-1.0V(Ic=-3A, IB=-0.3A),
VBE(sat)<=-2.0V(Ic=-3A, IB=-0.3A)
Paul Lamar
Those transistor could be a high speed switching power
supply that reduces the 12 volt car battery to 5 volts
for the computer.
BTW do any of you electronic types recognize
this semiconductor logo? An italic capital D with a line
under it.
--
Paul Lamar ...No rotor no motor.
Hi Paul,
They would not use a switching power supply to convert 12 volts DC to 5
volts DC.
Switching power supplies are used for converting AC to DC.
They would use a voltage regulator of some sort. Possibly a Diode working in
the reverse
breakdown range of 5 volts. So that anything above 5 volts would be clipped.
My guess is that those transistors feed the coil but without seeing the
schematics I can't say for sure.
A coil works by building a magnetic field by electrical current flowing
through it's windings. when that
flow is suddenly cut off, the magnetic field collapses and depending on the
number of windings the original
12 volts is amplified by the number of turns of wire in the coil creating
the high voltage discharge across the
spark plug, or igniter as they are referred to on this forum.
Dan
Dan, that coil switch you mentioned I am pretty sure
is in the coil and that is what is failing when
we fire it twice as often as a piston engine and/or over
heat it.
Switching power supplies are also used to reduce 14 Volts
to five volts as they are very efficient. Over 80% and as
high as 95%. They only sample the 14 volts every now and
then and filter the resultant pulse train in large
capacitors.
Linear regulators like Zener diodes and analog single chip five
volt regulators on the other hand are only about 35% efficient
(5/14) so there is a lot of wasted power and a lot of heat
generated. You must drop about 9 volts across the chip or a power
resistor. At 3 amps that is 27 watts. No small amount.
This RX8 PCM computer is probably drawing several amps out of the
battery or about 15 watts or so.
On the other hand these transistors could be used as a transmitter
...transmitting your speed and vehicle ID to a receiver on the side of
the road connected to a computer at the Highway Patrol office so
they can automatically send you a speeding ticket :) Also if your
check engine light comes on the EPA can arrest you for polluting:)
Now if there is a GPS chip in there and flash memory as well they
will know when and where and how fast you went for the last couple
of years :)
There are a couple of other power device on the board,
K2114 and K3225 what ever they are. No heat sink however.
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.