Subject: Renesis coil trouble fix and LS1
From: Rotary Engine
Date: 9/16/2006, 4:27 PM
To: AA-me


>>> Paul,
>>> Here is some information from Tracy on the coil
problem.
>>> Ian
>>>
>>> Coil/igniters are fairly critical on two things.
>>>
>>> (1) Ambient temps around coils should be kept
under 130 degrees when run
>>> at constant high rpm operation.  I enclose my
coils and have a blast
>>> tube blowing cool air into the enclosure to
ensure this.
>>>
>>> (2)  Dwell time on coil needs to be correct.  If
possible, measure the
>>> running dwell time on the coil (Pin A on RX8
coils, see instructions for
>>> location).  It should be close to 3
milliseconds.  I can't remember the
>>> details of your EC2 order but the Renesis
version can be ordered with
>>> one of two options,  LS1 coils (5 millisecond
dwell time) and RX-8 coils
>>> (3 MS).  If you have the wrong version the coils
could run hot (LS1
>>> running on RX-8 coils) or have weak spark (RX-8
running on LS1 coils).
>>>
>>>
>>> Ah so. Very good. All makes sense. Jibes with
what I measured
>>> on the RX8 car coils. I.E. 2.5 milliseconds.
I'll start mounting
>>> coils inside the ram air ducting for the
radiators in my 3D's :)
>>> Simple fix.
>>>
>>> Have you checked your dwell time yet Ian?
>>>
>>> Paul Lamar ...No rotor no motor.
>>>
>>
>> Yes 2.5ms.
>> I will send the cowl pictures soon.
>> Ian
>>
>> I have come to the conclusion, after looking at
the stock
>> RX8 computer PC board, the required power
switching transistors
>> or FETs MUST be in the coils. Search as I might I
cannot find
>> anything on the PC board that looks like a high
current FET's or
>> power transistors used for driving four coils.
>>
>> IMHO fuel injectors will soon have the power
switch integrated into
>> the injector body as well.
>>
>> Paul Lamar ...No rotor no motor.
>>
>
> Paul
>
> What about the  two transistors attached to the
heat sink in the upper > left
> of the board?
>
> DougFir
>
> I am not sure what they do. They might be the
injector switch.
> NEC B1453
> 2SB1453 PNP epitaxial silicon power transistor
> For fast switching.
> Functions PNP epitaxial silicon power transistor
> Applications For fast switching
> Features High DC amplification factor
> hFE>=100(VCE=-5V, IC=-0.5A)
> Full-mold package, easy mounting
> Performances VCBO=-60V, VCEO=-60V, VEBO=-7.0V
> Ic(DC)=-3A, PT=25W(Tc=25deg.C)
> PT=2.0W(Ta=25deg.C)
> hFE=100 to 400(VCE=-5V, Ic=-0.5A)
> VCE(sat)<=-1.0V(Ic=-3A, IB=-0.3A),
> VBE(sat)<=-2.0V(Ic=-3A, IB=-0.3A)
>
>
> Paul Lamar
>
> Those transistor could be a high speed switching
power
> supply that reduces the 12 volt car battery to 5
volts
> for the computer.
>
> BTW do any of you electronic types recognize
> this semiconductor logo? An italic capital D with
a line
> under it.
> -- > Paul Lamar ...No rotor no motor.


Hi Paul,
They would not use a switching power supply to
convert 12 volts DC to 5
volts DC.
Switching power supplies are used for converting AC
to DC.
They would use a voltage regulator of some sort.
Possibly a Diode working in
the reverse
breakdown range of 5 volts. So that anything above 5
volts would be clipped.
My guess is that those transistors feed the coil but
without seeing the
schematics I can't say for sure.
A coil works by building a magnetic field by
electrical current flowing
through it's windings. when that
flow is suddenly cut off, the magnetic field
collapses and depending on the
number of windings the original
12 volts is amplified by the number of turns of wire
in the coil creating
the high voltage discharge across the
spark plug, or igniter as they are referred to on
this forum.

Dan

Dan, that coil switch you mentioned I am pretty sure
is in the coil and that is what is failing when
we fire it twice as often as a piston engine and/or
over
heat it.

Switching power supplies are also used to reduce 14
Volts
to five volts as they are very efficient. Over 80%
and as
high as 95%. They only sample the 14 volts every now
and
then and filter the resultant pulse train in large
capacitors.

Linear regulators like Zener diodes and analog
single chip five
volt regulators on the other hand are only about 35%
efficient
(5/14) so there is a lot of wasted power and a lot
of heat
generated. You must drop about 9 volts across the
chip or a power
resistor. At 3 amps that is 27 watts. No small
amount.

This RX8 PCM computer is probably drawing several
amps out of the
battery or about 15 watts or so.

On the other hand these transistors could be used as
a transmitter
...transmitting your speed and vehicle ID to a
receiver on the side of
the road connected to a computer at the Highway
Patrol  office so
they can automatically send you a speeding ticket :)
Also if your
check engine light comes on the EPA can arrest you
for polluting:)

Now if there is a GPS chip in there and flash memory
as well they
will know when and where and how fast you went for
the last couple
of years :)

There are a couple of other power device on the
board,
K2114 and K3225 what ever they are. No heat sink
however.

Paul Lamar ...No rotor no motor.


Paul

Those pnp devices you are questioning would never
qualify for conventional ignition drivers with the
specs provided.
1. only a 60V rating where 400-500 is required(with
derating).
2. only a 3A rating where 10-15A is required (with
derating)
3. pnp devices aren't used as low side switches; an
npn or n chan fet is required.
They also are not suited to injector drives which
usually require 4A peak + derating and are usually low
side switches.

regards, Robert

I did not think so. What do you think they are using them
for? I hope not a transmitter. BTW do you know anything
about the LowJack transmitter. Could this be it?
-- 
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.