> > I think this is it
> >
> > Tony
> >
> > Yes much more practical Tony. Drilling a whole bunch of holes
> > 4 inches deep would take forever.
> >
> > I like this one much much better. See... those nuts were not all
> > that hard were they? :)
>
> Paul Lamar
>
> > ------------------------------------------------------------------------
>
> Tony,
> If you haven't acquired the drive yet, I would give Tracy a call and ask
> him about the extended shafts. He stated two or three months ago that
> he intended to begin offering some shaft length options for a small
> extra cost.
>
> Your idea is a good one. But, there may be some unexpected dynamic
> effects caused by moving the spline coupling flange this far off the
> plane of the isolation plate. If there is any imbalance the PSRU input
> shaft will experience a cantilever load. Some resonance effects could
> occur in the isolation plate. Tracy's isolation plate has worked pretty
> well so far. You would be introducing some new unknowns with this
> scheme. I'll bet that when Tracy sees your drawings, he will be even
> more motivated than before to offer some shaft length options! Give him
> a call.
>
> Tracy should offer a pre-drilled adapter plate and shaft for each type
> of Mazda bellhousing. I don't know how many there are. Do you know,
> Paul? The cost saved on the smaller (and maybe thinner) adapter plate
> would partially offset the additional cost of the shaft.
>
> Aubrey
>
> I am not sure. Tony has an auto TX version I think. But some manual
> TX bell housings can also be used. I am sure the RX8 has new and
> different bell housings becasue the six speed manual TX is new.
>
> Paul Lamar ...No rotor no motor.
>
>Paul
Yes I have automatic TX version is that the wrong one or does it
matter?
Aubrey
I gave some thought to your concerns on the harmonics. I agree tht is
an unknown. I looked at the exstension like a "prop exstension" I
will call Tracy on monday I hope he says "No problem" on the shaft
exstension.
the nice thing is this setup can easily be adapted to fit any bell
housing. I'll try to make it as light as possible if I can't get the
shaft extended from tracy at a resonable cost like less than $50.00
or so, I have a really nice lathe than I can turn this out in about
1hr. when it comes off of the lathe it's balanced pretty well.
I think that is Dynamic? I allways get confused on which balance
is what. Keep in mind too that I'm still using Tracys isolation mount
so wouldn't any type of harmonics be absorbed with that? I'll balance
the whole assembly before I put it on the airplane. Doug Mueller
and I will run the motor for at least 10hrs before I put it on the
Long Ez. Maybe I can identify any problems during that time.
paul
Is there anyway to figure out how this is going to affect
harmonics?
and if there is a problem will it be noticeable right away?
the other thing I want to mention is I think I can use my 89 flywheel
which is nice because I'm haveing a hard time finding an 87
Tony
No the auto TX bell house is fine.
The extension is pretty stiff and short so the torsional
harmonics should not be affected much if at all. Balance is important
but what you also need do is check the runout out after you have it
installed with a dial indicator on the rim of the extension. If you
have any problems they should show up when you static run the engine
with prop.
Paul Lamar ...No rotor no motor.
Good idea !
I'm almost done polishing the housing, going to send it to L.A.
and have it anodized either purple or blue. I want this install
to look amazing. I'm going to polish the redrive as well.
Tony
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.