Subject: P-port leak SS liner
From: Rotary Engine
Date: 9/17/2006, 1:45 PM
To: AA-me

snips
  >> ------------------------------------------------------
  >> The sleeve is an additional labyrinth seal. The water has to
  >> turn a couple of corners. If you bore all the way through
  >> you still have a simple leakage path.
  >> Hard to fix too. The thin SS sleeve cost less
  >> than $10 and there is no precision about it. Also there is no
  >> question about epoxy sticking to stainless steel. Way back
  >> in the early 1960's we made composite chassis race cars
  >> with SS reinforcements for bolt holes. We used SS
  >> because epoxy stuck to it better than aluminum.
  >> We also built some bonded aluminum chassis and we either
  >> anodized the parts first or etched them with some sort
  >> of solution I forget which. We were looking for maximum
  >> strength in the bond. I'll research that etching fluid shortly.
  >> This was long before Burt Rutan.
  >> Starting with four inch round and cutting most of the
  >> material off on the lathe leaving a flange is not practical.
  >> You need to weld a flange on the tube. You need the flange
  >> so you can take the engine apart. The original Teflon
  >> slide throttle design can be made by anybody with just hand
  >> tools and a modern saber saw. No lathe required. The hole in
  >> the rotor housing must be done on a mill however I have heard
  >> of people doing it with a hole saw.
  >> --
  >> Paul Lamar ...No rotor no motor.
  >
  Snips



I just came up with an idea that eliminates the small hole.
Here are a couple of pictures of the problem area.
This is the other side of the rotor housing from that
side I repotted on Marks engine.

Just clean this area up with a die grinder and hand cut
a chunk of aluminum that just slips in. Bond it in with
JB Weld BEFORE you cut the hole for the tube. Problem solved.

It won't help Marks engine but the Stainless steel sleeve
will do the same thing.
-- 
Paul Lamar ...No rotor no motor.

----------------------------------------------------------------------------------------------------------------------

As a possable solution to Marks concern and the possability of the tube
being sucked into the engine , Could you not stop a full diameter bore
just beyond the h2o jacket on the top end of the bore but just short of
the actual liner. This should keep the SS tube from ever being able to
move inward but at the same time adds extra surface area to the repair
for bonding and potential h20 leaks.

  If the SS tube is deemed necesarry for future bores( as a fail safe) it
to could be bored inplace and epoxied after the aluminum tube has been
potted and cured ??????????

Geir

---------------------------------------------------
I can't quite picture this. Can you do a sketch in MS Paint?
-- 
Paul Lamar ...No rotor no motor.

------------------------------------------------------------------------------------

I am assuming you will be boring Mark's aluminum tube to insert the SS
tube and still end up with the 1.875 ID as in the original configuration.

Regardless. If you bore the aluminum tube to the yellow line as shown
and epoxy the SS tube you end up sleeving all of the failed epoxy area
but at the same time by not continuing the bore all the way thru at the
top  it provides a seat for the SS tube so it can not move inward as
Mark was conerned about. The bottom of theSS tube would obviously be
trimmed to fit prior to being epoxied in place.

Geir

No bore. The Burns SS tube is .035 thick. I have some inquiries
out for even thinner wall. .015" or .020" paper thin.
Just a liner really. I should end up with 1.845" ID instead
of 1.875" ID. With 24 square inches of bonding area and 3000 psi
shear bonding strenght for JB Weld or a force of 72,000 pounds
to move the SS tube I don't think it is going anywhere in the
forseeable future :)  You could glue it in with chewing
gum and it would not go anywhere. If the glue strenght was
only ONE psi the force to move the tube would be 24 pounds.

I cut the SS tube off at an angle so there will be more over
lap up at the top where the pin hole leak was found.

BTW folks when you use MS Paint save as jpg rather than
bmp as bmp don't automatically show up on all browsers.


Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.