> > > > I think this is it
> > > >
> > > > Tony
> > > >
> > > > Yes much more practical Tony. Drilling a whole bunch of holes
> > > > 4 inches deep would take forever.
> > > >
> > > > I like this one much much better. See... those nuts were not all
> > > > that hard were they? :)
> > >
> > > Paul Lamar
> > >
> > >
> ------------------------------------------------------------------------
> > >
> > > Tony,
> > > If you haven't acquired the drive yet, I would give Tracy a call and
ask
> > > him about the extended shafts. He stated two or three months ago that
> > > he intended to begin offering some shaft length options for a small
> > > extra cost.
> > >
> > > Your idea is a good one. But, there may be some unexpected dynamic
> > > effects caused by moving the spline coupling flange this far off the
> > > plane of the isolation plate. If there is any imbalance the PSRU
input
> > > shaft will experience a cantilever load. Some resonance effects could
> > > occur in the isolation plate. Tracy's isolation plate has worked
pretty
> > > well so far. You would be introducing some new unknowns with this
> > > scheme. I'll bet that when Tracy sees your drawings, he will be even
> > > more motivated than before to offer some shaft length options! Give
him
> > > a call.
> > >
> > > Tracy should offer a pre-drilled adapter plate and shaft for each
type
> > > of Mazda bellhousing. I don't know how many there are. Do you know,
> > > Paul? The cost saved on the smaller (and maybe thinner) adapter plate
> > > would partially offset the additional cost of the shaft.
> > >
> > > Aubrey
> > >
> > > I am not sure. Tony has an auto TX version I think. But some manual
> > > TX bell housings can also be used. I am sure the RX8 has new and
> > > different bell housings becasue the six speed manual TX is new.
> > >
> > > Paul Lamar ...No rotor no motor.
> > >
> > >Paul
> >
> > Yes I have automatic TX version is that the wrong one or does it
> > matter?
> >
> > Aubrey
> >
> > I gave some thought to your concerns on the harmonics. I agree tht is
> > an unknown. I looked at the exstension like a "prop exstension" I
> > will call Tracy on monday I hope he says "No problem" on the shaft
> > exstension.
> > the nice thing is this setup can easily be adapted to fit any bell
> > housing. I'll try to make it as light as possible if I can't get the
> > shaft extended from tracy at a resonable cost like less than $50.00
> > or so, I have a really nice lathe than I can turn this out in about
> > 1hr. when it comes off of the lathe it's balanced pretty well.
> > I think that is Dynamic? I allways get confused on which balance
> > is what. Keep in mind too that I'm still using Tracys isolation mount
> > so wouldn't any type of harmonics be absorbed with that? I'll balance
> > the whole assembly before I put it on the airplane. Doug Mueller
> > and I will run the motor for at least 10hrs before I put it on the
> > Long Ez. Maybe I can identify any problems during that time.
> >
> > paul
> > Is there anyway to figure out how this is going to affect
> > harmonics?
> > and if there is a problem will it be noticeable right away?
> >
> > the other thing I want to mention is I think I can use my 89 flywheel
> > which is nice because I'm haveing a hard time finding an 87
> >
> > Tony
> >
> > No the auto TX bell house is fine.
> >
> > The extension is pretty stiff and short so the torsional
> > harmonics should not be affected much if at all. Balance is important
> > but what you also need do is check the runout out after you have it
> > installed with a dial indicator on the rim of the extension. If you
> > have any problems they should show up when you static run the engine
> > with prop.
> >
> > Paul Lamar ...No rotor no motor.
>
>
> Good idea !
>
> I'm almost done polishing the housing, going to send it to L.A.
> and have it anodized either purple or blue. I want this install
> to look amazing. I'm going to polish the redrive as well.
>
> Tony
> hi Tony, if you use a series 5 flywheel on a series 4 rotors you will
have an out of balance engine. take care wyo. walt
I don't think he means flywheel walt. I think he means auto TX flex
plate. Nobody flys a flywheel. Too heavy.
Of course the rear counter weight must be correct.
Paul Lamar
Yes FLEX PLATE sorry!
I should get my parts back from Racing beat this week, had the
motor balanced with all the counter weights and llapped the housing.
I'm polishing my rotor housings now once that is done I'll have my
housings powder coated, then I can put it all back together and make
some noise.
I'm redoing my titanium studs for my motor so I can use the the
little rubber sealing O-Rings in the rear housing. I'll draw it
out for you.
Tony
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.