RE>> Hello Paul,
RE>> I have decided to use a different fuel and ignition system on the
RE>> Renesis in the Mustang2. I have decided to use throttle injection
RE>> bodies as I have been impressed with the performance of the one I
RE>> am running on my Jabiru 3300. Therefore I have one EC2 and a LCD
RE>> EM2 for sale. This is the large panel. I will build an ignition system
RE>> similar to the Jabiru. I'v done a lot of work on the new system and am
RE>> happy with the results so far. I plan to dyno the engine after all the
RE>> mods are done. I am also waiting for the new weight that RAA in
RE>> Australia are pushing for with CASA. I will not go through
RE>> registration until it is clear and the new regs are out.
RE>> Best regards,
RE>> ddunbar
mailto:ddunbar@echidna.id.au
RE>> Do you have any pictures of those TIB's Don?
RE>> Paul Lamar
RE> Hello Paul,
RE> They are from Revmaster. I have one on the Pulsar with the 3300 Jabiru
RE> in. It took some tuning but I was going through a learning curve. What
RE> I know now it would take no time to tune.
RE> The little bird photo is for Robbin.
RE> Friday, September 29, 2006, 9:57:19 PM, you wrote:
RE> Best regards,
RE> ddunbar
mailto:ddunbar@echidna.id.au--
RE> Thanks for the pictures Don.
RE> What are you going to use for the center ports?
RE> Those TIB's might be useful for P-ports.
RE> Paul Lamar
RE> On second thought the 40 mm (1.57") size is still marginal
RE> for a p-port. The price seems right however at $320 for
RE> a 34 mm version. Too bad he does not make a 51 mm version
RE> for P-port rotaries.
RE>
http://www.revmasteraviation.com/products/revflow_injector_carburetor/index.htm
RE> Paul Lamar ...No rotor no motor.
The Revmaster carby was flow tested to match the Renesis engine.
There
efficiency is a lot better than the Bing on the Jabiru. with the Bing
static was 2600 rpm and with the Revmaster 2700+. The throttle
response is instant and I need to be careful. I only use the screw on
the verier throttle on power up. I used ram air with the setup and
found it was way to lean at the top end. After filling the needle to
richen the top end it is performing great. I think the 38 mm carb
would have been enough as I now don't use wide open throttle and the
slide is restricted by the stops for the last 6mm.
In the evaluation
of this setup one has to consider there is no need for a fuel pump and
they run on gravity feed. I have always's been concerned about the high
pressure fuel in the engine bay and you will say good bye with a leak.
I have now flown 50 hour with the Revmaster on the Jabiru 3300 powered
Pulsar. I believe that this is the way we should be going as we don't
need to adapt a motor vehicle system to suite the aero situation.
I can now cruise at 150 knots plus using 14 liter per hour. I have a
great combination in this setup. Today I flew down South to a farm fly
in. Once again the throttle response on the sort strip was great and
the many people that where watching where all impressed.
In conclusion we are not looking for the flexibility of the computer
EMS and we don't need it as our propeller curve will show a straight
line with a fixed pitch.
I will dyno the new setup in the next few months.
I agree with you Paul that the best system would be a PP engine. The
combination with this type of carby and a simple system to fire the
ignition set at 20 deg advance is all we require.
If you go to a constant speed or a in flight adjustable then you may
need a more advance system.
--
Best regards,
ddunbar
mailto:ddunbar@echidna.id.au
What are you going to do about the two center ports? If you
don't use them you will be lucky to see 120 HP. What size carb do
you have? 34 mm, 36 mm, 38mm, or 40 mm?
Who flow tested it on a RX8 engine? How did they do it using
only two carbs on a six port engine? What intake manifold did
they use.
I am not disputing the ignition. I am skeptical of the
carb. You will need a Y in the manifold as a minimum
and then two 40 mm 1.57 inch diameter carbs are going
to be very marginal as far as power is concerned.
Most people use a dual 48 mm Weber carb as a minimum.
Many use the 51 mm Weber carb. There is no magic sucking air
through a hole? :)
Don't get me wrong there is nothing wrong with carbs.
Especially aircraft carbs than can be leaned.
You will still need a fuel pump on a low wing airplane like
the Mustang II.
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.