Subject: Newbie and the mounts/rads questions........
From: Rotary Engine
Date: 10/2/2006, 2:34 PM
To: AA-me



Yes, boo-koo hours have gone into her testing and design. The foils are
NACA/Langley 11% supercritical symmetricals with clam-shell drag rudders
for yaw, matched ailerons on all four wings for roll, and elevators
working as one on all four wings for the pitch control against said long
nose. Since the ship is heavy for her size, crabbing is not as big an
issue as one might think(I think the nose length has a lot to do with it
as she really tries to point well)....especially since she lands cleanly
at around 130MPH(kicking the nose over just before setting down seems to
do the trick.) Her dual Matco brakes with their triple caliper
assemblies will make sure she can stop from as high as 150MPH, and the
tires are matched to that performance level. Testing on the models has
not shown an acute issue of setting down on the wing outriggers, since
the mains actually touchdown quickly after, and she soon straightens out
on their drag while braking. I though I had a "dragonfly" issue with
those outrigger assemblies, but neither the sim nor the models bore that
out. She rotates on her own around 90MPH due to the nose profiles'
ambient lift, but I hold her nose down and loft her quickly at about
130MPH for safety. In the sim, and on the models, she is much steadier
than the standard issue cambered foil ships due mainly to the lack of
lift from the symmetrical wings; basically, she squats nice, flat and
steady on her engine power which is why I chose the rotary engine and
it's limited catastrophic failure modes. She finals at ~20% power, and
cruises better than 300MPH on only 75% power. Top speed according to the
sim is 340MPH at 11,000ft, and ~325MPH at sea-level. The fuel
tank(26gal) is directly on CG, and since it is a single pilot/no
passenger/luggage ship, the CG does not adjust inflight so adverse
pitching moments are limited in all but the most violent manuevers. CG
is 6" forward of leading wing edge according to both models and
simulator. I have tested both models and the sim bird with canards,
mostly extreme aspect canards to preserve the speed, but honestly, the
ship doesn't need them IMHO(I do, however, like one of my latest version
with a retractable, sweepable canard.) In any event, I have heard the
warnings about new design, new engine type, new psru all in one ship,
and thus I have relyed on my 12 years as a Marine parachute rigger to
install the 62' ballistically-actuated cargo 'chute to bring her back
safely as required. Needless to say, there will be a belly-pack 'chute
on me as well. Bottom line is that I don't know all the technical
reasons why she flies, but everything I've tried has verified she will.
The glider community were the first folks to really acknowledge that
it's more of a rocket than a plane, and should fly with no real issues,
especially with a totally static CG. Oddly enough, the sim likes her
best at her current CG, ~1500-1700lbs, with 300-500HP at 9,000RPM on a
psru of 3:1. I've tested her as heavy as 2800lbs(hollow wings full of
fuel)with four 700lbft thrust jet engines, and she is extremely
maneuverable around 500-600MPH, but she becomes twitchy above mach due
to vortices betwixt the wings. The sim helped tremendously with
eventually coming to the conclusion that the ventral and dorsal fins
would be much more amiable for speed and manuvering than the hollow
engine tubes of the traditional form. You should have seen the anarchy
in the sim when first trying out non-symmetrical foils!!!!

Anyhew......I still need those suggestions for rad plumbing(including
suggestions for intake locales)and the oil pump/waterpump. Thanks!



The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.