Subject: Long Ez/ Rhino pics
From: Rotary Engine
Date: 10/11/2006, 7:35 PM
To: AA-me


> > Paul
> >
> > I've been messing with Rhino. The scoop is what I have in mind to
> > house my radiators and oil cooler. I plan on putting an augmenter
> > in there somewhere. Can you give me an idea of the optimum scoop
> > layout in other words is this one going to work? I want to use
> > the two radiators forming a wedge like a greater than sign
> > I know the drawing is a little rough. I don't have a full grasp
> > on Rhino yet still importing parts from Auto Cad.
> >
> > Tony
> >
> > You are getting pretty good with Rhino Tony.
> > That scoop will work fine. Where is the air coming out after
> > it passes through the rads? At least as important as
> > how it gets in.
> >
>
> Paul
>
> the idea is to have the augmenter in the scoop so the exit to the
> air is going to be just under the prop flange. think of it like
> a turboprop facing backwards only instead of intake air it will
> be exhaust gas pulling air thru the front of the scoop thru a
> duct between the tires and then out the back of the airplane.
> the only thing is I'm not sure exactly how an augmenter works.
> I mean I know what it does but the shape eludes me. Kinda of
> a Brunelli thing right? I'm sure you can help me with that.
>
> Tony
>
> What are the dimensions of the duct between the tires?
>
> If you have a side view in Rhino put some dimensions
> on it and turn on dimensions in the rendering program,
> render it and up load it to us. Same for a top view.
> That way we can check scale and figure other dimensions.
>
> -- > Paul Lamar ...No rotor no motor.
>
> Does not look like you have a whole heck of a lot of
> room to get much air past that landing gear.
>
> Paul Lamar ...No rotor no motor.

paul

That is an old Pic with the Cessna 210 gear on the bottom of the
fuse, that was for concept only. I've designed my own retracts
for the airplane. I'll do the dimensions for you when I get home
from work today.

I think off the top of my head the fuse is around 24"in wide
where the rads are going to go.

Tony

Tony are you a mechanical engineer? I have some friends
that are talented mechanical engineers and they screwed
up on the Nemesis Nxt gear design :) Several have crashed
so far. Supposedly they had help from the Lockheed Martin
Skunk works. Obviously it is not easy to design a good retract.

Paul Lamar ...No rotor no motor.



Tony and Paul,

   I wanted to put the augmenter tube below the engine exiting under the
prop flange.  The length of the augmentor in that configuration is limited.
A while ago I decided I needed more space behind the rad and oil cooler to
provide adequate flow so I decided to pressurize the whole cowl.  Looking at
the top of the engine and reading the NACA paper on rectagular augmeters I
found that if I used a somewhat retangular tube the tube could go on the top
and be up to 30" long.  Well within the specs in the paper.  Furthermore
heat rises so why cook our installations during ground ops and post
shutdown.  The trick is the exhaust header.  Again I found that the overall
length of the pipes join up in the augmentor at thsame distance for an
optimum tuned P port senario.  It will have to be shielded but it should be
doable.  Most of the tube will be exposed to air as it will be a part of the
top cowl kind of like a shaker hood scoop found on the late 60s muscle cars.
Shoehorning a rotary installation into the Long EZ is quite a bit different
than the Cozy Mk IV they have twice as much width in the engine compartment.
I still am amazed at how Tom Jordan did his. Take it for what it's worth.

Joe Berki
Limo EZ
Priming and sanding and sanding



The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.