Bruce,
Am I hearing you right " Direct Injection"?
This will require some high pressure air to atomize the fuel at the point
of
injection - do you have a preferred Injector placement position?
Stratified charge as Paul mentions, seems to happen naturally.
As the exhaust escapes at supersonic speed beyond idle, The exhaust
doesn't
need any additional help in fact if the inlet charge isn't delayed it will
actually suck in some charge as it self evacuates - apparently some
additional air sucked in to the exhaust is beneficial. This has been
confirmed by some German information Paul has on the Rotary.
Can you elaborate on what you have in mind.
George ( down under)
George,
Thanks for your interest.
I am not sure how to use this list, but I will give it a go.
Project engine is a Peripheral Port Mazda 13B engine. Don't have it yet
in
my possession.
Contemplating how to make it into a streetable and economical power plant
for my REPU.
Thinking of installing a high pressure injector as far as possible into
the
13B trailing spark plug hole and using it to inject a pulse of gas or
hydrogen into the combustion recess soon after the leading apex seal
passes
by.
With an undersize turbo I hoped to pressurize the peripheral port intake
during idle RPM and above.
To start with the object would simply be to see if I could get a smooth
idle
with this PP race motor.
The turbo would hopefully pressurize the intake sufficiently to flush any
exhaust gas backward out the exhaust port below the pinched waist of the
epitrochoidal chamber. Thus a clean, exhaust gas free air charge would
work
its way around to the top, trailing spark plug hole where I would inject
some fuel. Said fuel should be drawn past the pinched waist of the rotor
housing on that side and move past the leading spark plug where said
stratified charge would be ignited. I would thus have the beginnings of a
tractable Peripheral Port Mazda 13B engine which should, theoretically
also
get good gas mileage.
I just found out that GM is installing a high pressure direct injection
system, with a special Borg-Warner dual-scroll turbo in their 2007 Saturn
has direct injection in its Sky Red Line roadster. I have put together an
email on this based on the article at
http://www.gmhightechperformance.com/features/0609htp_2007_saturn_sky_red_line/
if anyone is interested. Email me at agent007
AT
doitnow DOT com
Otherwise I may be stuck adapting the following systems:
Porsche 911 Bosch DI unit
Alfa Spica DI unit
also, the following maring two strokes now are using direct injection ..
Mercury OptiMax (V6 or 3 in line)
http://www.mercurymarine.com/153
Evinrude E-TEC 114 V4, 105CID
http://www.evinrude.com/en-CA/Engines/Showroom/ProductSpecs.htm?productID=ETEC115
Nissan TLDI NSD 115
http://www.nissanmarine.com/products/115_tldi_specs.html
Yamaha HPDI (V6)
http://www.yamaha-motor.com/outboard/feat_hpdi_2006.aspx
why Compression Ratio only 6.2:1?
I also like Mr. Lamar's idea of using exhaust heat / energy to help turn
the
eccentric shaft. Is anyone selling the parts necessary to pull this off
with a 13B engine ?
Thanks,
Bruce Toski
Mazda Certifications
Master ASE Certification
Former Auto Vo-Tech instructor
1972 Audi 100LS and 1986 Audi 5000
1974 Mazda REPU (Rotary Engine PickUp truck)
(Former owner of R100, RX-3, RX-2, RX-4, Cosmo, NSU RO80 engine, Sachs
Wankel chainsaw, Sach Motocross prototype motorcycle, Graupner radio
control
airplane engine,84 RX-7 SE, Hercules W2000 Wankel motorcycle, Suzuki RE-5
Wankel motorcycle)
Web: www.DPQ.US
Bruce,
You may find the DI system is a development of someone else, although it's
hardly rocket science now that it's been done by so many Companies, as you
indicated. Orbital Engine Technologies was one of the first to supply
European Government bodies - now everyone seems to have it.
What I like about the GM system is that it should be readily available.
I don't know it I like your intension of DI through the spark plug hole, as
I wouldn't like to eliminate a spark plug, for obvious reasons - however
there's a new system which has a combination of spark plug with integral DI
which would suite the purpose - but I don't think it's readily available.
With DI the problem with idle/overlap/ contamination of the inlet charge is
a non-issue, I wouldn't spend too much time on that. I would however
consider an injection prior to the spark plugs with a simple injector bung
into the aluminum housing - as is done with the P-port.
George (down under)
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.