Subject: 13B with peripheral port, turbo, direct injection stratified charge
From: Rotary Engine
Date: 10/13/2006, 10:21 PM
To: AA-me



 > Bruce,
 > Am I hearing you right  " Direct Injection"?
 >
 > This will require some high pressure air to atomize the fuel at the
point
 > of
 > injection - do you have a preferred Injector placement position?
 >
 > Stratified charge as Paul mentions, seems to happen naturally.
 >
 > As the exhaust escapes at supersonic speed beyond idle, The exhaust
 > doesn't
 > need any additional help in fact if the inlet charge isn't delayed it
will
 > actually suck in some charge as it self evacuates - apparently some
 > additional air sucked in to the exhaust is beneficial. This has been
 > confirmed by some German information Paul has on the Rotary.
 >
 > Can you elaborate on what you have in mind.
 > George ( down under)
 >
 >
 > George,
 > Thanks for your interest.
 > I am not sure how to use this list, but I will give it a go.
 >
 > Project engine is a Peripheral Port Mazda 13B engine.  Don't have it yet
 > in
 > my possession.
 > Contemplating how to make it into a streetable and economical power plant
 > for my REPU.
 > Thinking of installing a high pressure injector as far as possible into
 > the
 > 13B trailing spark plug hole and using it to inject a pulse of gas or
 > hydrogen into the combustion recess soon after the leading apex seal
 > passes
 > by.
 > With an undersize turbo I hoped to pressurize the peripheral port intake
 > during idle RPM and above.
 > To start with the object would simply be to see if I could get a smooth
 > idle
 > with this PP race motor.
 > The turbo would hopefully pressurize the intake sufficiently to flush any
 > exhaust gas backward out the exhaust port below  the pinched waist of the
 > epitrochoidal chamber.  Thus a clean, exhaust gas free air charge would
 > work
 > its way around to the top, trailing spark plug hole where I would inject
 > some fuel.  Said fuel should be drawn past the pinched waist of the rotor
 > housing on that side and move past the leading spark plug where said
 > stratified charge would be ignited.  I would thus have the beginnings
of a
 > tractable Peripheral Port Mazda 13B engine which should, theoretically
 > also
 > get good gas mileage.
 >
 > I just found out that GM is installing a high pressure direct injection
 > system, with a special Borg-Warner dual-scroll turbo in their 2007 Saturn
 > has direct injection in its Sky Red Line roadster.  I have put
together an
 > email on this based on the article at
 >
http://www.gmhightechperformance.com/features/0609htp_2007_saturn_sky_red_line/
 > if anyone is interested.  Email me at                       agent007
 > AT
 > doitnow      DOT      com
 >
 > Otherwise I may be stuck adapting the following systems:
 >
 > Porsche 911 Bosch DI unit
 > Alfa Spica DI unit
 > also, the following maring two strokes now are using direct injection ..
 > Mercury OptiMax (V6 or 3 in line)
 > http://www.mercurymarine.com/153
 > Evinrude E-TEC 114 V4, 105CID
 >
http://www.evinrude.com/en-CA/Engines/Showroom/ProductSpecs.htm?productID=ETEC115
 > Nissan TLDI NSD 115
 > http://www.nissanmarine.com/products/115_tldi_specs.html
 > Yamaha HPDI (V6)
 > http://www.yamaha-motor.com/outboard/feat_hpdi_2006.aspx
 > why Compression Ratio only 6.2:1?
 >
 > I also like Mr. Lamar's idea of using exhaust heat / energy to help turn
 > the
 > eccentric shaft.  Is anyone selling the parts necessary to pull this off
 > with a 13B engine ?
 >
 > Thanks,
 >
 > Bruce Toski
 >
 > Mazda Certifications
 > Master ASE Certification
 > Former Auto Vo-Tech instructor
 >
 > 1972 Audi 100LS and 1986 Audi 5000
 > 1974 Mazda REPU (Rotary Engine PickUp truck)
 >
 > (Former owner of R100, RX-3, RX-2, RX-4, Cosmo, NSU RO80 engine, Sachs
 > Wankel chainsaw, Sach Motocross prototype motorcycle, Graupner radio
 > control
 > airplane engine,84 RX-7 SE, Hercules W2000 Wankel motorcycle, Suzuki RE-5
 > Wankel motorcycle)
 >
 >
 > Web: www.DPQ.US <http://www.DPQ.US>

Bruce,
You may find the DI system is a development of someone else, although it's
hardly rocket science now that it's been done by so many Companies, as you
indicated. Orbital Engine Technologies was one of the first to supply
European Government bodies - now everyone seems to have it.
What I like about the GM system is that it should be readily  available.
I don't know it I like your intension of DI through the spark plug hole, as
I wouldn't like to eliminate a spark plug, for obvious reasons - however
there's a new system which has a combination of spark plug with integral DI
which would suite the purpose - but I don't think it's readily available.
With DI the problem with idle/overlap/ contamination of the inlet charge is
a non-issue, I wouldn't spend too much time on that. I would however
consider an injection prior to the spark plugs with a simple  injector bung
into the aluminum housing - as is done with the P-port.
George (down under)

George,

Well, any contamination by inert exhaust gas is not good in my book.
Question is how difficult will it be to implement a turbo to provide
positive pressure at low rpm ...
Do provide me with the name of whoever is contemplating manufacture
of an integral spark plug / injector.
I have made some inquiries but no results yet.
It looks like lowest BSFC is obtained in the position slightly ahead
of the minor axis, ... see page 216, The Wankel Engine, by Jan Norbye
(Curtiss Wright engine development under Max Bentele).
Patent 3,246,636
http://www.uspto.gov/patft/index.html

Pic attached.

I am trying NOT to open or alter the engine I am receiving in order to
retain resale value if my ideas do not pan out.

On another tangent ..... I thought I read an article somewhere about an
unthrottled GDI (gasoline direct injection engine) that varied the HP
by varying the amount of gasoline injected ( no throtte plate, like a diesel).
Anyone else remember seeing this or am I losing it ?

Bruce Toski




The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.