Subject: p-port butterflies
From: Rotary Engine
Date: 10/13/2006, 6:33 AM
To: AA-me




> Paul,   I am planning on running a twm throttle body for my initial
> p-port intake system , at least until I get all the bugs worked out of
my
> install.  I have heard that the slide throttles in general may not be
> quite as forgiving as a carb or TB at or near approach  throttle
> settings and I'm just a little concerned about adding the slide throttle
> to a lot of other things to be concerned with on initial flights. My
> thought is to use a Wiggins clamp where racing beat uses a hose
> connection and this enables me to swap to carbs for remote bush flying
> and efi  TB or slide throttle for local flying.
>
> My question is what size TB would you recommend for the 1.875 I.D.
> p-port insert.Would the efficiency be improved by slightly oversizing
the
> TB to make up for throttle plate restriction. TWM provides 48,50, and 55
> MM TB's in the 3000 series.
>
> My plan on the primary injectors is to possibly weld an injector boss on
> the insert before boring and epoxy and install it as close to the rotor
> housing as possible. The injector bosses in the TWM  TB would be used
> for the secondary;s.
>
> Check out weld on injector bosses at sdsefi.com.  very clean install and
> for $37 hard to beat.
>
> What are your thoughts on TB size and injector location
>
> Thanks   , Geir
>
> All  you guys concerned with the slide throttle position
> as a function of HP generated make the hole in the Teflon
> tear drop shaped. Don't make it round. I'll do a drawing for
> you shortly. You can have your cake and eat it too.
> -- > Paul Lamar ...No rotor no motor.
>
> -------------------------------------------------
>
> Here is the dwg. I added an inch to the back plates on
> the rear housing end (car). An unanticipated advantage is
> the total throttle cable travel is increased from 2 inches
> to three inches making fine adjustments easier.
>
> I can understand if you don't want to build one of these and just
> throw money at the problem by buying a TB but be advised
> butterfly's will cut the HP and burn slightly more fuel.
>
> Best use the 55 mm TB but then you will have to make a smooth
> transition from 1.875" (47.625 mm) to the 55 mm throttle body.
>
> If you use the 48 mm instead you will lose more HP and burn more
> fuel and you will still have to make a smooth transition.
>
> -- > Paul Lamar ...No rotor no motor.
>
> ------------------------------------------------
>
> Hi Paul,
>
> Please explain the teardrop slide.  All I can see is turbulence at WOT
> as the charge rushes by the edge of the teardrop.
> How is this better than a lens shaped orifice at idle setting with the
> plain circular hole.
> BR, Dave McC
>
> Well the slide almost never stays in that position for long.
> Perhaps for awhile on approach. In that case you don't really
> care about the turbulence. But the rate of opening area, as
> a function of throttle cable position, is lower so it is
> a bit easier to set a specific engine RPM.
>
> You get turbulence past the butterfly all of the time.
> -- > Paul Lamar ...No rotor no motor.
>
> -----------------------------------------------
>
> Paul , Assuming I use a pair of 55mm TB's, what might you suggest as a
> minimum length for the taper from 47.625 to 55mm.
>
> Thanks, Geir
>
> Good question. I would guess an S curve three  or four
> inches long. Are you using a 180 bend in the runners?
>
> BTW what are you paying for that set of TB's ?
>
> Paul Lamar ...No rotor no motor.
>
>
> Paul,     Yes , I am planning on u-bends in the range of 22-28''
>
> The bore center to center is 120 mm
>
> I am able to get the TB's at close to wholesale.
>
> Thanks,  Geir
>
> I forgot to mention the TWM throttle body spacing is the same
> as a Weber carb. As such it is too close together. You need
> the butterfly's further apart and close to the rotor housing
> else your long runners will store contaminated with exhaust gas
> mixtures that will result in extreme misfiring at low RPM. That
> is why the slide throttle is located close to the rotor housings
> as possible. That is also why Everette Hatch put the butterfly's
> inside the rotor housings.
>
> Paul Lamar ...No rotor no motor.
>
> Paul,     I planned to incorporate the center to center difference of
> the TB's with the same adapter plate that would couple the p-port stubs
> to the TB's . I am guessing the throttle plate would be about 4-5" from
> the outside of the rotor housing . This would add roughly 2-3 " to that
> of the slide throttle distance.
>
> I have a tough time debating your slide throttle with all the time and
> testing you have put into the design, not to mention my minimal time
> involved with the group . I do have some experience with Teflon products
> in racing application and I am a little concerned with the possibility
> of the Teflon fracturing due to fatigue and/or cold intake temps during
> startup and potentially being ingested. I have had Teflon shatter under
> extreme cold and race applications on snowmobiles. Is there any data on
> Teflon to put my concern to rest.The throttle response at approach speed
> ( in my case 45-60 knots) and the integrity of the Teflon are my only
> concerns,other than that ,once again the dyno run speaks for itself
> performance wise.
>
> Thanks for your time,   Geir
>
> I need to see a sketch or 3D of what you are proposing.
>
> It is hard for me to believe the Teflon will shatter in
> close proximity to a 200 degree F engine but I guess anything
> is possible at -50 degrees F below zero. Our metal car door handles
> used to snap off in the winter time in Northern Ontario.
>
> Since we went up to 3/8 thick Teflon the slide is now cannon
> proof. According to McMaster Carr Teflon is good down to -350 F.
> Are you planning on going to the moon? :)
>
> Are you sure those snowmobile parts were Teflon?
>
> Paul Lamar ...No rotor no motor.
>

--------------------------------------------------------------------------
----
> --------------------------------------------------------
> Paul, I couldn't expect to" not" get just a little bit of shit for
> asking . The Teflon was worn to perhaps 1/8 to 3/16 thick and serves as
> a wear  surface between the steel cleets on the track and the aluminum
> slide rails that guide the track. If the track is loose the cleets beat
> the living ba jesus out of the Teflon , not to mention speeds of 100
plus
> mph and temps of 20 to 40 below on rare occasions assisting in the
> torture. There is shock impact from all angles so its not exactly fair
> to compare the slide throttle to this abuse but when it comes to flying
> hotrod engines over many miles of trees and rough terrain one can never
> ask enough silly questions.Anyhow what your sharing makes perfect sense
> and I thank you for your patience.
>
> Geir
>
> What everybody needs to do with these experimental engines
> is learn how to side slip. One of the airline pilots at SZP
> was dragging his new Berkut in on the second flight
> at 3 degrees like one would land an airliner. Engine quit... had
> to set it down on the freeway slicing off the top of a Honda in
> the process. People were hurt but not killed.
>
> If you side slip and your engine dies on approach no problem.
> You can still land. Also if you side slip it is easier to
> put it down on the numbers as the decent angle is much greater
> than 3 degrees. You can almost point the wing at the spot
> you want to touch down. Altitude is always your friend.
>
> Unfortunately the FAA took this out of the pilot training
> curriculum.
> -- > Paul Lamar ...No rotor no motor.

Paul,


Wow a lot has change in the way they teach.  I was taught to never depend
on
the engine in landing or at least assume it wouldn't save your butt if you
got too low.  Of course spins was part of the curriculum as well.  What's
next to be dropped, basic navigational skills?


Doug Fir

Why do you need VORs and dead reckoning when you have GPS? :)

BTW stop by SZP on your way home as I will not be at
Copper State. I will be at Seven Stock. I think you would
learn more if you came to Seven Stock on Saturday instead.
You could talk to the guys running P-ports and 4 rotor turbo's
on their  street cars :)

Paul Lamar ...No rotor no motor.

Paul,

When and where is Seven Stock being held?  I would love to attend
myself.

Bryan


Where: Mazda North America Corporate HQ Center --
Irvine, California

Did you know: this years SevenStock is at a new location?
On Saturday morning, don't go to Mazda R&D on Reynolds!
Go to Mazda Corporate HQ at 7755 Irvine Center Dr, Irvine Ca
Tell your friends too... don't let them end up at the wrong
location!

http://www.sevenstock.org/



Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.