> Bruce,
> You may find the DI system is a development of someone else, although
it's
> hardly rocket science now that it's been done by so many Companies,
as you
> indicated. Orbital Engine Technologies was one of the first to supply
> European Government bodies - now everyone seems to have it.
> What I like about the GM system is that it should be readily available.
> I don't know it I like your intension of DI through the spark plug hole,
> as
> I wouldn't like to eliminate a spark plug, for obvious reasons - however
> there's a new system which has a combination of spark plug with integral
> DI
> which would suite the purpose - but I don't think it's readily available.
> With DI the problem with idle/overlap/ contamination of the inlet charge
> is
> a non-issue, I wouldn't spend too much time on that. I would however
> consider an injection prior to the spark plugs with a simple injector
> bung
> into the aluminum housing - as is done with the P-port.
> George (down under)
>
> George,
>
> Well, any contamination by inert exhaust gas is not good in my book.
> Question is how difficult will it be to implement a turbo to provide
> positive pressure at low rpm ...
> Do provide me with the name of whoever is contemplating manufacture
> of an integral spark plug / injector.
> I have made some inquiries but no results yet.
> It looks like lowest BSFC is obtained in the position slightly ahead
> of the minor axis, ... see page 216, The Wankel Engine, by Jan Norbye
> (Curtiss Wright engine development under Max Bentele).
> Patent 3,246,636
>
http://www.uspto.gov/patft/index.html
>
> Pic attached.
>
> I am trying NOT to open or alter the engine I am receiving in order to
> retain resale value if my ideas do not pan out.
>
> On another tangent ..... I thought I read an article somewhere about an
> unthrottled GDI (gasoline direct injection engine) that varied the HP
> by varying the amount of gasoline injected ( no throtte plate, like a
> diesel).
> Anyone else remember seeing this or am I losing it ?
>
> Bruce Toski
Bruce,
Information to me is that GM DI is very much like the Siemens - strange as
that may seem!
The drawing attached shows the injector blowing fuel past the spark plug, I
guess for stratified charge advantages. This may not be necessary with the
natural tendency for stratified charge of the Rotary i.e. centrifugal
forces.
The company that developed the spark plug with Integral Injector is an
American firm which developed the Orbital system - can't remember the Coy
but Bill Jepson might as we were jointly researching DI some time ago.
BTW contamination of the inlet charge with exhaust is tolerated by most
engines - to a degree, just check their overlap. Elimination would only be
an advantage, if it were easy to achieve and if it provided significant
improvement in performance (volumetric efficiency), the Rotary can achieve
over 100% VE with standard timing, with NA as it is.
Turbo would most likely push fresh air into the exhaust, if you manage to
achieve pressure at idle - as you suggest.
Personally I would like to see the injector at 12.20 to 1.00 O'clock, angled
to drive fuel to the spark plugs.
These are only my ideas and not intended to divert you from your desired
objectives. Please do with them as you wish.
George ( down under)
George,
Thanks for the info / input.
One of the reasons for low NOx in the Wankel is the dilution of the
intake charge.
Just another loss of efficiency factor I would like to minimize.
Love the air curtain idea Paul ! Had not thought of that one !
Now, the natural stratified charge you mention is hard to control and
probably only works at higher rpm.
I believe ultimate efficiency at part throttle / lower rpms is only
going to happen with direct injection.
The low BSFC figures mentioned for the LeMans engine etc are great but I
don't believe they are going to hold up against the recip under light
load / part throttle conditions without direct injection. I see this as
the main way to get aroung the achille's heel of the wankel, it's
relatively poor surface to volume ratio. I don't see any way around the
inherent shorter lever length problem ( " e " or eccentricity ) which is
about 1/2 of what most comparable recips have, right ? Does anyone have
an opinion how much this factor alone affects fuel economy / torque ?
In the Rolls Royce diesel Wankel (the 2-R6 produced 325 hp @ 4500 RPM
and weighed 929 pounds) the injector was placed a few degrees before the
minor axis. ( This is what Norbye states but his diagrams show the
injector just after the minor axis) In the Rolls Diesel Wankel, the
exhaust charge exited the exhaust port and entered one half of the
wankel compressor and helped drive it .... similar to Mr. Lamar's idea
of using exhaust energy to drive a turbine of some sort which in turn
helped drive the eccentric shaft again ! I have not been able to find
much on this Rolls Wankel. Norbye says in his book, " The technical
details of their experimantal engines have been classified information
under the terms of British Government contracts" This is still true all
these years later ? All I know is development stopped in 1974 after
Rolls had a bout with bankruptcy ?
On your injector position (1 O clock high) ... holes in the rotor casing
should be avoided at this area to prevent leakage backwards during the
combustion cycle.
Interested in patents, especially as concerns the Wankel ?
see:
http://www.uiausa.org/Publications/FreeBook/PPart9.pdf
start reading at page 14. (ok this guy is a little biased against the
Wankel I think, as some of his statements are not correct, factually
speaking)
Wankel's 1958 USA patent for the wild DKM
patent number 2,988,065 (33 pages)
http://patft.uspto.gov/netacgi/nph-Parser?patentnumber=2988065
Wankel's 1957 USA patent for the KKM
http://patft.uspto.gov/netacgi/nph-Parser?patentnumber=2988008
I love Wikipedia
http://en.wikipedia.org/wiki/Wankel_engine
http://de.wikipedia.org/wiki/Wankelmotor
http://en.wikipedia.org/wiki/Wankel (section on aircraft engines !)
Perhaps the wildest thing I read .....
"Perhaps the most exotic use of the Wankel design is in the seat belt
<http://en.wikipedia.org/wiki/Seat_belt> pretensioner system of the
Volkswagen
<http://en.wikipedia.org/wiki/Volkswagen> New Beetle
<http://en.wikipedia.org/wiki/New_Beetle>. In this car, when
deceleration
<http://en.wikipedia.org/wiki/Deceleration> sensors
<http://en.wikipedia.org/wiki/Sensor> sense a potential crash, small
explosive cartridges are triggered electrically and the resulting
pressurized gas feeds into tiny Wankel engines which rotate to take up
the slack in the seat belt systems, anchoring the driver and passengers
firmly in the seat before any collision."
*** Looks like this might be covered under SAE *Document Number: *980557
SAE
http://www.sae.org/servlets/index has over 100 very interesting
papers on the Wankel but they are now priced at about $10 each. If I
could just find a less expensive way to get these .... Maybe I could
copy them at a local University ???
Here is a nice animation !
http://www.keveney.com/Wankel.html
All for now .... time for bed.
zzzzzzzz
Toski
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.