Subject: with peripheral port, turbo, direct injection stratified charge
From: Rotary Engine
Date: 10/14/2006, 4:30 PM
To: AA-me



Bruce,
You may find the DI system is a development of someone else, although it's
hardly rocket science now that it's been done by so many Companies, as you
indicated. Orbital Engine Technologies was one of the first to supply
European Government bodies - now everyone seems to have it.
What I like about the GM system is that it should be readily  available.
I don't know it I like your intension of DI through the spark plug hole, as
I wouldn't like to eliminate a spark plug, for obvious reasons - however
there's a new system which has a combination of spark plug with integral DI
which would suite the purpose - but I don't think it's readily available.
With DI the problem with idle/overlap/ contamination of the inlet charge is
a non-issue, I wouldn't spend too much time on that. I would however
consider an injection prior to the spark plugs with a simple  injector bung
into the aluminum housing - as is done with the P-port.
George (down under)

George,

Well, any contamination by inert exhaust gas is not good in my book.
Question is how difficult will it be to implement a turbo to provide
positive pressure at low rpm ...
Do provide me with the name of whoever is contemplating manufacture
of an integral spark plug / injector.
I have made some inquiries but no results yet.
It looks like lowest BSFC is obtained in the position slightly ahead
of the minor axis, ... see page 216, The Wankel Engine, by Jan Norbye
(Curtiss Wright engine development under Max Bentele).
Patent 3,246,636
http://www.uspto.gov/patft/index.html

Pic attached.

I am trying NOT to open or alter the engine I am receiving in order to
retain resale value if my ideas do not pan out.

On another tangent ..... I thought I read an article somewhere about an
unthrottled GDI (gasoline direct injection engine) that varied the HP
by varying the amount of gasoline injected ( no throtte plate, like a diesel).
Anyone else remember seeing this or am I losing it ?

Bruce Toski


Bruce,
Information to me is that GM DI is very much like the Siemens - strange as
that may seem!
The drawing attached shows the injector blowing fuel past the spark plug, I
guess for stratified charge advantages. This may not be necessary with the
natural tendency for stratified charge of the Rotary i.e. centrifugal
forces.
The company that developed the spark plug with Integral Injector is an
American firm which developed the Orbital system - can't remember the Coy
but Bill Jepson might as we were jointly researching DI some time ago.
BTW contamination of the inlet charge with exhaust is tolerated by most
engines - to a degree, just check their overlap. Elimination would only be
an advantage, if it were easy to achieve and  if it provided significant
improvement in performance (volumetric efficiency), the Rotary can achieve
over 100% VE with standard timing, with NA as it is.
Turbo would most likely push fresh air into the exhaust, if you manage to
achieve pressure at idle - as you suggest.
Personally I would like to see the injector at 12.20 to 1.00 O'clock, angled
to drive fuel to the spark plugs.
These are only my ideas and not intended to divert you from your desired
objectives. Please do with them as you wish.
George ( down under)


If you guys are interested in preventing exhaust gas
getting into the fresh charge you are going to need some
sort of seal. The only seal I can think of right at
the moment is a high pressure air curtain. A mechanical
seal won't work because of the bath tube combustion chamber
in the face of the rotor.

BTW even the side exhaust port RX8
engines carries forward some exhaust gas contained in the
bath tub area of the rotor.

Drill a bunch of small holes in the rotor housing  about
in the place shown and supply with high pressure air.

Patent applied for......Just kidding.

-- 
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.