> George,
>
> I love the idea of a "pretend-jet" as you put it, but not for the
> boy-wow factor -- I actually think there could be a way to
make such
> an
> airplane work quite well -- even for bigger-than-sport plane
size.
>
> Here's my idea. Please feel free to poke holes in it: (Paul I
know you
> don't need an invitation to fire away).
>
> An airplane like the Diamond D-jet or Excel Sport jet weights
about
> 5000
> pounds gross, will go about 350 mph at 25,000 feet, stall at
not much
> more than a high-performance piston single and have a range
of about
> 1000 miles, roughly.
>
> These planes, although not yet certified, are a very exciting
> development. I've seen the D-jet take off and climb out and it is
> actually much quieter than a Cirrus, displaying the kind
civilized,
> confident deportment that only a jet plane can. Flying in one
would be
> very very comfortable, I'm sure -- what without the piston
vibration,
> prop blast against the windshield, etc. After seeing this
baby at a
> local field, I thought, "man, this is a nice way to fly." And
that
> "whoosh" sound...who could go back to propellers?
>
> Call me crazy, but I think that there exists the potential to
make
> this
> concept even better using rotary power and a ducted fan. Or
at least
> as
> good, but much less expensive.
>
> Now I'm not talking about the big ducts that we see on ducted
fan
> small
> planes, like that Optica or even Perry Mick's Long-EZ, or
that nice
> little Legati triangular wing job. I'm talking about a 24-inch
> diameter
> duct at most, contained within the fuselage, as in the D-Jet
and Sport
> jet, and with two intake scoops on the sides.
>
> The problem with the big ducts is not just the added drag of
the extra
> wetted area, but also that these huge surfaces can act like a
big sail
> and cause stability problems and all kinds of aerodynamic grief.
>
> George mentioned the misconception that rotary or piston
engines can
> drive a duct as good as a turbine. This is indeed a
misconception
> because, generally this is an impossible dream. For one thing, a
> rotary
> or piston engine is much bigger in diameter than a turbine,
which can
> be
> quite a small round cylinder making a huge amount of power
for its
> size.
>
> This is important because you have the engine in the center
of the
> duct
> and if your engine is big around the middle, you have to have
a big
> duct. You also have a lot of blockage to the air stream in the
> middle of
> the duct where the engine is sitting. Of course the engine is
> streamlined with a fairing, but even so that fairing adds
quite a bit
> of
> wetted area against which the high-speed air stream has to work.
>
> My idea is eliminate the engine in the middle of the duct. In
fact the
> engine will not be in the duct at all. The duct would be
incorporated
> into the fuselage as on the D-jet and Sport jet, as
mentioned. But the
> rotary engine would be sitting ahead of the duct, inside the
fuselage
> proper. A short drive shaft would poke from this engine
compartment
> into
> the center of the duct and drive the single-stage fan.
>
> All you would have inside this duct is the fan itself. There
would be
> no
> blockage whatsoever. In this regard, it is even better than a
> turbofan.
> You would not have any of the drag of the air stream against the
> engine
> fairing. And since the air stream is moving quite fast, this
drag is
> not
> insignificant, even with the small diameter of a turbine engine.
>
> Also, since the duct is completely within the fuselage you
have no
> additional outside wetted area, no sail effect, no
aerodynamic issues
> of
> any kind.
>
> So what about efficiency? I think it could be quite good, even
> compared
> to a propeller plane. Don't forget that with a prop plane you
have the
> high-speed prop slipstream causing friction against the
surface of the
> plane. This causes higher drag than the parasite drag from the
> undisturbed air, because the prop slipstream air is moving much
> faster.
> This also causes some aerodynamic issues, such as the
left-turning
> tendency from the prop slipstream pushing against the rudder,
etc.
>
> A 24 -inch fan would result in a fan speed of about mach .75
at 7500
> engine rpm, direct drive. If you wanted to use a higher rpm
P-ported
> engine, you could move the rpm range up a bit and use an even
smaller
> fan diameter. This small diameter duct would present a
relatively
> small
> wetted area inside the duct and would decrease friction drag
and help
> efficiency. And with no engine in the duct -- and no blockage of
> airflow
> -- efficiency would also be improved considerably. In fact,
if you
> wanted to use an even smaller duct and a higher speed jet
effect, you
> could gear up the engine to turn the fan faster than engine
speed.
>
> Ideally, the engine would be turbo compounded for great
specific fuel
> consumption, as well as maintaining high power at altitude.
This is in
> fact something that even turbines can't do -- their power
drops with
> altitude.
>
> The fuel load would therefore be considerably smaller as a
ratio of
> total airplane weight. The 5000 pound jets we're talking
about here
> carry about one third of that weight as fuel (1700 pounds or
so). A
> turbo compound rotary with a SFC of under .4 could do the
same on
> little
> more than half the fuel, assuming equal power. You could count on
> saving
> at least 700 to 800 pounds of fuel weight.
>
> Yes the engine will be a little heavier, but maybe 200 pounds
at most.
> The 1300 pound thrust Williams FJ33 in the D-jet weighs 300
pounds.
> You
> could probably build a very powerful 3-rotor engine for under 500
> pounds
> I'm sure -- less if aluminum castings are available. So you
would
> still
> be able to have a gross weight 500 pounds lighter.
>
> There is no reason why you could not scale this idea down to
say a
> four-seater with a smaller engine, or even a two-seater with a
> 2-rotor.
>
> Regards,
>
> Gordon.
>
> This idea has some merit.
>
> The 1300 pound thrust at sea level Williams engine is probably
> developing one third of that at 30,000 feet or about 430 pounds.
> TSFC (pounds burned per pound of thrust) for a small turbo fan
> might be as low as 1.3 at this altitude so fuel burn would be
> about 560 pounds an hour or 93 gallons
> an hour. With 1120 pounds of fuel or 186 gallons on board
> range at 450 MPH would be 900 miles. 4.8 MPG. Every year
> at OSH I would stop by the Williams booth and ask about
> the TSFC every year they would not tell me :)
>
> At 400 MPH or 586 FPS that would be 459 equivalent thrust HP.
> At 450 MPH if it will go that fast 660 FPS or about Mach .5 In
> that case the equivalent thrust HP would be 516 HP net.
>
> Rotary engine power required with a .6 eff. duct would be 860
HP.
> Fuel burn at .4 BSFC (TC) would be 344 pounds per hour or 57
gallons
> an hour or 8 MPG. Range would be about 900 miles with 120
gallons.
>
> Cooling required would be a major design effort. Some of the
> boost pressure would be diverted to pressurize the
> cabin.
>
> Its been done and I will upload some pictures shortly.
>
>
> Paul Lamar
>
> I don't think we are at the peak of propeller design efficiency
yet. If
> you have heard a dash8 400Q flying, you know that they have more
going
> on with their prop designs than what we get on direct drive LyCont
> engines. Since the rotary really needs a gear reduction unit
anyway, we
> have flexibility in choosing a prop RPM that's much quieter. The
> airframe obviously needs room to have a large diameter prop..
>
>
> Regards,
>
> Matt-
>
> That is why the turbo prop verses biz jet argument is still
> going on. Piaggio Avanti in particular is at the forefront of that
> argument.
>
>
http://www.artdisk.it/proposta_piaggio/htm/piaggioaero.htm
<http://www.artdisk.it/proposta_piaggio/htm/piaggioaero.htm>
>
> Paul Lamar ...No rotor no motor.
Fuel consumption. Hmmmmmm. Is this a bad time to ask just what kind of
fuel you intend to burn? And whether it will be available at the
airports
you visit? George W>
Hello George,
Not sure what you're getting at there. Until somebody makes a rotary
run really well on something other than gasoline, that's the only
choice, as far as I am concerned.
Matt-
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.