Subject: Ducted fan airplanes
From: Rotary Engine
Date: 10/20/2006, 1:42 PM
To: AA-me


George,

I love the idea of a "pretend-jet" as you put it,
but not for the
boy-wow factor -- I actually think there could be a
way to make such
an
airplane work quite well -- even for
bigger-than-sport plane size.

Here's my idea. Please feel free to poke holes in
it: (Paul I know
you
don't need an invitation to fire away).

An airplane like the Diamond D-jet or Excel Sport
jet weights about
5000
pounds gross, will go about 350 mph at 25,000 feet,
stall at not much
more than a high-performance piston single and have
a range of about
1000 miles, roughly.

These planes, although not yet certified, are a very
exciting
development. I've seen the D-jet take off and climb
out and it is
actually much quieter than a Cirrus, displaying the
kind civilized,
confident deportment that only a jet plane can.
Flying in one would
be
very very comfortable, I'm sure -- what without the
piston vibration,
prop blast against the windshield, etc. After seeing
this baby at a
local field, I thought, "man, this is a nice way to
fly." And that
"whoosh" sound...who could go back to propellers?

Call me crazy, but I think that there exists the
potential to make
this
concept even better using rotary power and a ducted
fan. Or at least
as
good, but much less expensive.

Now I'm not talking about the big ducts that we see
on ducted fan
small
planes, like that Optica or even Perry Mick's
Long-EZ, or that nice
little Legati triangular wing job. I'm talking about
a 24-inch
diameter
duct at most, contained within the fuselage, as in
the D-Jet and
Sport
jet, and with two intake scoops on the sides.

The problem with the big ducts is not just the added
drag of the
extra
wetted area, but also that these huge surfaces can
act like a big
sail
and cause stability problems and all kinds of
aerodynamic grief.

George mentioned the misconception that rotary or
piston engines can
drive a duct as good as a turbine. This is indeed a
misconception
because, generally this is an impossible dream. For
one thing, a
rotary
or piston engine is much bigger in diameter than a
turbine, which can
be
quite a small round cylinder making a huge amount of
power for its
size.

This is important because you have the engine in the
center of the
duct
and if your engine is big around the middle, you
have to have a big
duct. You also have a lot of blockage to the air
stream in the middle
of
the duct where the engine is sitting. Of course the
engine is
streamlined with a fairing, but even so that fairing
adds quite a bit
of
wetted area against which the high-speed air stream
has to work.

My idea is eliminate the engine in the middle of the
duct. In fact
the
engine will not be in the duct at all. The duct
would be incorporated
into the fuselage as on the D-jet and Sport jet, as
mentioned. But
the
rotary engine would be sitting ahead of the duct,
inside the fuselage
proper. A short drive shaft would poke from this
engine compartment
into
the center of the duct and drive the single-stage
fan.

All you would have inside this duct is the fan
itself. There would be
no
blockage whatsoever. In this regard, it is even
better than a
turbofan.
You would not have any of the drag of the air stream
against the
engine
fairing. And since the air stream is moving quite
fast, this drag is
not
insignificant, even with the small diameter of a
turbine engine.

Also, since the duct is completely within the
fuselage you have no
additional outside wetted area, no sail effect, no
aerodynamic issues
of
any kind.

So what about efficiency? I think it could be quite
good, even
compared
to a propeller plane. Don't forget that with a prop
plane you have
the
high-speed prop slipstream causing friction against
the surface of
the
plane. This causes higher drag than the parasite
drag from the
undisturbed air, because the prop slipstream air is
moving much
faster.
This also causes some aerodynamic issues, such as
the left-turning
tendency from the prop slipstream pushing against
the rudder, etc.

A 24 -inch fan would result in a fan speed of about
mach .75 at 7500
engine rpm, direct drive. If you wanted to use a
higher rpm P-ported
engine, you could move the rpm range up a bit and
use an even smaller
fan diameter. This small diameter duct would present
a relatively
small
wetted area inside the duct and would decrease
friction drag and help
efficiency. And with no engine in the duct -- and no
blockage of
airflow
-- efficiency would also be improved considerably.
In fact, if you
wanted to use an even smaller duct and a higher
speed jet effect, you
could gear up the engine to turn the fan faster than
engine speed.

Ideally, the engine would be turbo compounded for
great specific fuel
consumption, as well as maintaining high power at
altitude. This is
in
fact something that even turbines can't do -- their
power drops with
altitude.

The fuel load would therefore be considerably
smaller as a ratio of
total airplane weight. The 5000 pound jets we're
talking about here
carry about one third of that weight as fuel (1700
pounds or so). A
turbo compound rotary with a SFC of under .4 could
do the same on
little
more than half the fuel, assuming equal power. You
could count on
saving
at least 700 to 800 pounds of fuel weight.

Yes the engine will be a little heavier, but maybe
200 pounds at
most.
The 1300 pound thrust Williams FJ33 in the D-jet
weighs 300 pounds.
You
could probably build a very powerful 3-rotor engine
for under 500
pounds
I'm sure -- less if aluminum castings are available.
So you would
still
be able to have a gross weight 500 pounds lighter.

There is no reason why you could not scale this idea
down to say a
four-seater with a smaller engine, or even a
two-seater with a
2-rotor.

Regards,

Gordon.

This idea has some merit.

The 1300 pound thrust at sea level Williams engine
is probably
developing one third of that at 30,000 feet or about
430 pounds.
TSFC (pounds burned per pound of thrust) for a small
turbo fan
might be as low as 1.3 at this altitude so fuel burn
would be
about 560 pounds an hour or 93 gallons
an hour. With 1120 pounds of fuel or 186 gallons on
board
range at 450 MPH would be 900 miles. 4.8 MPG.  Every
year
at OSH I would stop by the Williams booth and ask
about
the TSFC every year they would not tell me :)

At 400 MPH or 586 FPS that would be  459 equivalent
thrust HP.
At 450 MPH if it will go that fast 660 FPS or about
Mach .5 In
that case the  equivalent thrust HP would be 516 HP
net.

Rotary engine power required with a .6 eff. duct
would be 860 HP.
Fuel burn at .4 BSFC (TC) would be 344 pounds per
hour or 57 gallons
an hour or 8 MPG. Range would be about 900 miles
with 120 gallons.

Cooling required would be a major design effort.
Some of the
boost pressure would be diverted to pressurize the
cabin.

Its been done and I will upload some pictures
shortly.


Paul Lamar

Actually, I have a buddy in Denver who has been
working for a few years
on
such an aircraft but haven't heard from him for a
while and he may have
given up.  He's a Toyota master mechanic and was using
a 200 hp MR-2
engine
driving a 28 inch dia fan.  He elected to build an
aircraft similar in
appearance to an F-5.  His drive-shaft extends via a
fairing into the
portion of the duct where the twin intakes meet to
drive the rotor.  He
built a full-size test item of the propulsion section
and was finishing
up
the engine mods the last time we talked.

I agree with Paul that the cooling
issues almost drive this type of aircraft.  You really
need a very high
power density engine which pretty much demands liquid
cooling.  My
buddy
went with a pusher approach and a mid-engine.  I
haven't seen the
details of
how he would cool it, but I suspect he's thought it
out carefully.
He's
aiming at about 250 mph and driving the fan about 7000
rpm.  There are
bearing issues at these speeds and I don't know if
he's had the numbers
run
regarding vibration and resonance on the short drive
shaft.

There is a
tendency for designers to assume that direct-drive is
the way to go.
Interestingly, the majority of the "successful" ducted
fan designs tend
to
incorporate a gear box.  They've learned that very
high speed fans are
noisy.  Use of a stator section can help with this.
On the other hand,
RFB
found at one point that their gearbox noise had become
really annoying
and
had to change boxes.  Typical aircraft development
glitches.  Inlets
are a
topic providing hours of "fun".  A ducted or shrouded
system doesn't
need
the same kind of protruding inlet as a turbojet or
fan.  In throttled
back
or engine out conditions, these types of inlet are
actually a
detriment.  A
simple flush inlet (NOT NACA) is perfectly feasible.

One of the major
misconceptions is that a ducted inlet system is
limited to the 8 deg
ramp
limit typical of turbojets.  There is strong evidence
that Raymer's
observation that pusher aircraft can have up to 30 deg
of after body
angle
into a propeller without separation problems is
correct.  It turns out
this
seems to apply to ducted or shrouded fans.  You don't
have the boundary
layer issues with the ducted/shrouded systems typical
of turbojets.
Your
inlet does not have to be raised to get past the
boundary layer into
laminar
air.  The ducted/shrouded systems cheerfully suck in
the boundary
layer.

I would be fascinated to talk to the guy from Raytheon
about his
project.
Haven't heard of it before.

George W>


------------------------------------------

george or paul,

for a flush inlet, would there be any advantage to
placing it on the top side of the airframe near the
wing root, would it increase lift?

if you were designing the plane to operate at high
speed would a variable sliding door on the flush
intake affect the operational window/efficiancy of the
fan?

would variable fan blades be any better than the
variable intake in allowing the take off performance
and cruise efficiency, or could they be used togethor?

my dream (probably many years off) is to build a
pressurized high speed (+500) ducted fan plane with
the range to fly non-stop from texas to south america.
two fans, two turbo-compound rotary engines with
enough extra power at altitude to make it back to land
on one engine. how's that for a big dream, but i
figure the rotarys maybe will have the power to do it
if we get the bsfc low enough so less fuel needs to be
carried. i was thinking about maybe some sort of
canard design.

gary



The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.