> George,
>
> I love the idea of a "pretend-jet" as you put it, but not for
the
> boy-wow factor -- I actually think there could be a way to
make such
> an
> airplane work quite well -- even for bigger-than-sport plane
size.
>
> Here's my idea. Please feel free to poke holes in it: (Paul I
know you
> don't need an invitation to fire away).
>
> An airplane like the Diamond D-jet or Excel Sport jet weights
about
> 5000
> pounds gross, will go about 350 mph at 25,000 feet, stall at
not much
> more than a high-performance piston single and have a range
of about
> 1000 miles, roughly.
>
> These planes, although not yet certified, are a very exciting
> development. I've seen the D-jet take off and climb out and it
is
> actually much quieter than a Cirrus, displaying the kind
civilized,
> confident deportment that only a jet plane can. Flying in one
would be
> very very comfortable, I'm sure -- what without the piston
vibration,
> prop blast against the windshield, etc. After seeing this
baby at a
> local field, I thought, "man, this is a nice way to fly." And
that
> "whoosh" sound...who could go back to propellers?
>
> Call me crazy, but I think that there exists the potential to
make
> this
> concept even better using rotary power and a ducted fan. Or
at least
> as
> good, but much less expensive.
>
> Now I'm not talking about the big ducts that we see on ducted
fan
> small
> planes, like that Optica or even Perry Mick's Long-EZ, or
that nice
> little Legati triangular wing job. I'm talking about a 24-inch
> diameter
> duct at most, contained within the fuselage, as in the D-Jet
and Sport
> jet, and with two intake scoops on the sides.
>
> The problem with the big ducts is not just the added drag of
the extra
> wetted area, but also that these huge surfaces can act like a
big sail
> and cause stability problems and all kinds of aerodynamic
grief.
>
> George mentioned the misconception that rotary or piston
engines can
> drive a duct as good as a turbine. This is indeed a
misconception
> because, generally this is an impossible dream. For one thing,
a
> rotary
> or piston engine is much bigger in diameter than a turbine,
which can
> be
> quite a small round cylinder making a huge amount of power
for its
> size.
>
> This is important because you have the engine in the center
of the
> duct
> and if your engine is big around the middle, you have to have
a big
> duct. You also have a lot of blockage to the air stream in the
> middle of
> the duct where the engine is sitting. Of course the engine is
> streamlined with a fairing, but even so that fairing adds
quite a bit
> of
> wetted area against which the high-speed air stream has to
work.
>
> My idea is eliminate the engine in the middle of the duct. In
fact the
> engine will not be in the duct at all. The duct would be
incorporated
> into the fuselage as on the D-jet and Sport jet, as
mentioned. But the
> rotary engine would be sitting ahead of the duct, inside the
fuselage
> proper. A short drive shaft would poke from this engine
compartment
> into
> the center of the duct and drive the single-stage fan.
>
> All you would have inside this duct is the fan itself. There
would be
> no
> blockage whatsoever. In this regard, it is even better than a
> turbofan.
> You would not have any of the drag of the air stream against
the
> engine
> fairing. And since the air stream is moving quite fast, this
drag is
> not
> insignificant, even with the small diameter of a turbine
engine.
>
> Also, since the duct is completely within the fuselage you
have no
> additional outside wetted area, no sail effect, no
aerodynamic issues
> of
> any kind.
>
> So what about efficiency? I think it could be quite good, even
> compared
> to a propeller plane. Don't forget that with a prop plane you
have the
> high-speed prop slipstream causing friction against the
surface of the
> plane. This causes higher drag than the parasite drag from the
> undisturbed air, because the prop slipstream air is moving much
> faster.
> This also causes some aerodynamic issues, such as the
left-turning
> tendency from the prop slipstream pushing against the rudder,
etc.
>
> A 24 -inch fan would result in a fan speed of about mach .75
at 7500
> engine rpm, direct drive. If you wanted to use a higher rpm
P-ported
> engine, you could move the rpm range up a bit and use an even
smaller
> fan diameter. This small diameter duct would present a
relatively
> small
> wetted area inside the duct and would decrease friction drag
and help
> efficiency. And with no engine in the duct -- and no blockage
of
> airflow
> -- efficiency would also be improved considerably. In fact,
if you
> wanted to use an even smaller duct and a higher speed jet
effect, you
> could gear up the engine to turn the fan faster than engine
speed.
>
> Ideally, the engine would be turbo compounded for great
specific fuel
> consumption, as well as maintaining high power at altitude.
This is in
> fact something that even turbines can't do -- their power
drops with
> altitude.
>
> The fuel load would therefore be considerably smaller as a
ratio of
> total airplane weight. The 5000 pound jets we're talking
about here
> carry about one third of that weight as fuel (1700 pounds or
so). A
> turbo compound rotary with a SFC of under .4 could do the
same on
> little
> more than half the fuel, assuming equal power. You could count
on
> saving
> at least 700 to 800 pounds of fuel weight.
>
> Yes the engine will be a little heavier, but maybe 200 pounds
at most.
> The 1300 pound thrust Williams FJ33 in the D-jet weighs 300
pounds.
> You
> could probably build a very powerful 3-rotor engine for under
500
> pounds
> I'm sure -- less if aluminum castings are available. So you
would
> still
> be able to have a gross weight 500 pounds lighter.
>
> There is no reason why you could not scale this idea down to
say a
> four-seater with a smaller engine, or even a two-seater with a
> 2-rotor.
>
> Regards,
>
> Gordon.
>
> This idea has some merit.
>
> The 1300 pound thrust at sea level Williams engine is probably
> developing one third of that at 30,000 feet or about 430
pounds.
> TSFC (pounds burned per pound of thrust) for a small turbo fan
> might be as low as 1.3 at this altitude so fuel burn would be
> about 560 pounds an hour or 93 gallons
> an hour. With 1120 pounds of fuel or 186 gallons on board
> range at 450 MPH would be 900 miles. 4.8 MPG. Every year
> at OSH I would stop by the Williams booth and ask about
> the TSFC every year they would not tell me :)
>
> At 400 MPH or 586 FPS that would be 459 equivalent thrust HP.
> At 450 MPH if it will go that fast 660 FPS or about Mach .5 In
> that case the equivalent thrust HP would be 516 HP net.
>
> Rotary engine power required with a .6 eff. duct would be 860
HP.
> Fuel burn at .4 BSFC (TC) would be 344 pounds per hour or 57
gallons
> an hour or 8 MPG. Range would be about 900 miles with 120
gallons.
>
> Cooling required would be a major design effort. Some of the
> boost pressure would be diverted to pressurize the
> cabin.
>
> Its been done and I will upload some pictures shortly.
>
>
> Paul Lamar
>
> I don't think we are at the peak of propeller design efficiency
yet. If
> you have heard a dash8 400Q flying, you know that they have more
going
> on with their prop designs than what we get on direct drive LyCont
> engines. Since the rotary really needs a gear reduction unit
anyway, we
> have flexibility in choosing a prop RPM that's much quieter. The
> airframe obviously needs room to have a large diameter prop..
>
>
> Regards,
>
> Matt-
>
> That is why the turbo prop verses biz jet argument is still
> going on. Piaggio Avanti in particular is at the forefront of that
> argument.
>
> http://www.artdisk.it/proposta_piaggio/htm/piaggioaero.htm
<http://www.artdisk.it/proposta_piaggio/htm/piaggioaero.htm>
>
> Paul Lamar ...No rotor no motor.
Fuel consumption. Hmmmmmm. Is this a bad time to ask just what kind
of
fuel you intend to burn? And whether it will be available at the
airports
you visit? George W>
Hello George,
Not sure what you're getting at there. Until somebody makes a rotary
run really well on something other than gasoline, that's the only
choice, as far as I am concerned.
Matt-
Sorry, Matt, I tend to look across the range of powerplants and forgot you
were concentrating on a rotary. My impression is that rotaries are
relatively insensitive to octane - am I right? I seem to remember owning a
1973 RX-3 and its owner's manual claiming that it ran well on 60 octane
fuel. I've never heard of this octane before, but they didn't seem worried
about anything we could buy here. Many of the airports don't have mogas.
Can you run on aviation fuel without damage or increased maintenance?
George W
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.