> > > > Paul
> > > >
> > > > I want to put the stock tension bolts back in my motor but I don't
> > > > want to make a mess squirting a bunch of silicone in the holes to keep
> > > > them from vibrating. There has to be a better way. what about using
> > > > heat shrink tubing? maybe I can build it up so the tension bolts fit
> > > > snug in there respective holes.
> > > >
> > > > Tony
> > > >
> > > > Sounds like it is worth a try. Try a test sample. Heat it
> > > > in the oven to about 220 F and see what happens to the
> > > > heat shrink tubing. Silicone is good to 500 F.
> > >
> > > Paul Lamar
> > >
> > > Tony,
> > > You don't need to squirt a bunch of silicone in the holes. Just put
> > > about a 2 turn spiral bead along the bolt length and push it through.
> > > This insures that there is more on one end than the other. The purpose
> > > is to interfere with resonance mode vibrations that could possibly
> > > occur. It doesn't take much silicone to do that.
> > >
> > > Aubrey
> > >
> > Aubrey
> >
> > I'm very aware of the reason for doing it. What I don't like though is the
> > mess it makes when you have to take your motor apart not to mention,
> > (from what I understand) the silicone makes taking apart your motor
> > alot more difficult. Of course, this is secound hand information, it
> > sounds like it 's a plausible issue and it came from what I would
> > consider a reliable source. Seems like some heat shrink tubing will
> > do the trick and is much cleaner. I may just make some sort of mold
> > that I can squirt the silicone into that I can just slip it over the
> > tension bolt. Any ideas ?
> > maybe McMaster has something I can use.
> >
> > Tony
>
> O.K. I think I've got it. I'll cover the tension bolt with
> silicone insert the bolt into a piece of thin wall alluminum
> tubing, then I'll insert the tension bolt into the engine, which
> now has a nice smooth outer alluminum finish. That should work
> and it will look good too even though I can't see it. They will
> pull out with no mess if I need to tear down the engine. I woke
> up at 3:00am this morning and wrote it down I had a dream about it.
> I need to get a life LOL :)
>
> Tony
>
> That is a pretty good idea Tony. Now the devil is in the details.
> Where do you get exactly the right ID/OD of tubing.
> Turning it on a lathe 18 inches long is not easy.
> --
>
Paul
Why does it have to be one continuous piece? I'll bet I could put 3 or 4 1in pieces along the tension bolt and that would do the trick as Aubrey said, it doesn't take a whole lot to get the job done.
So why not just make 1in aluminum spacers? That might work. I think that Mcmaster has something that will be the right size. The only dim you really need is the I.D. of the holes in the castings. The
I.D. of the spacers can be filled with sillicone or reamed to the correct I.D. I'll bet Mcmaster has some unthreaded standoffs that will work great and they are pretty cheap as well. I'm at work but
if someone could get me the I.D. of the casting holes I'll look online at Mcmaster and see what I can find that will work.
Tony
Well I suspect the casting holes are not aligned bored
so they may vary in ID. I don't have any housings here
so somebody measure some holes. Adding a few lead or tungsten
spacers would break up the resonant frequency.
--
Paul Lamar ...No rotor no motor.
Paul
McMaster definitely has some tubing that will work. The telescoping
hobby aluminum or brass as Aubrey suggested will probably be a
really nice and cheap (not to mention light weight) way to go.
The tension bolt is .375 or 3/8 so I.D. of the tubing should be
around .400 maybe allow some room for silicone. I don't think the
tubing actually has to touch the walls of the housing,Iron or
aluminum. Of course now,you have to make sure that the concentrically
is fairly good as you will be turning the entire assembly in the hole.
OR maybe use a light coat of Vaseline on the tension bolt and when
the silicone cures the bolt will simply turn isinde the whole
assembly that's if the concentrically is to far off. Otherwise it
may be like a cam of sorts. Follow Me on that????
Tony
Yes getting it to go in might be a REAL problem if it
is NOT concentric.
I think you would be better off just wrapping it with
silicone tape.
But let us know success or failure. We learn from mistakes
as well as successes.
--
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.