Subject: there has to be a better way
From: Rotary Engine
Date: 10/30/2006, 11:45 PM
To: AA-me



    > > > > > Paul
    > > > > >
    > > > > > I want to put the stock tension bolts back in my motor
   but I don't
    > > > > > want to make a mess squirting a bunch of silicone in the
   holes to keep
    > > > > > them from vibrating. There has to be a better way. what
   about using
    > > > > > heat shrink tubing? maybe I can build it up so the
   tension bolts fit
    > > > > > snug in there respective holes.
    > > > > >
    > > > > > Tony
    > > > > >
    > > > > > Sounds like it is worth a try. Try a test sample. Heat it
    > > > > > in the oven to about 220 F and see what happens to the
    > > > > > heat shrink tubing. Silicone is good to 500 F.
    > > > >
    > > > > Paul Lamar
    > > > >
    > > > > Tony,
    > > > > You don't need to squirt a bunch of silicone in the
   holes.  Just put
    > > > > about a 2 turn spiral bead along  the bolt length and push
   it through.
    > > > > This insures that there is more on one end than the
   other.  The purpose
    > > > > is to interfere with resonance mode vibrations that could
   possibly
    > > > > occur.  It doesn't take much silicone to do that.
    > > > >
    > > > > Aubrey
    > > > >
    > > > Aubrey
    > > >
    > > > I'm very aware of the reason for doing it. What I don't like
   though is the
    > > > mess it makes when you have to take your motor apart not to
   mention,
    > > > (from what I understand) the silicone makes taking apart your
   motor
    > > > alot more difficult. Of course, this is secound hand
   information, it
    > > > sounds like it 's a plausible issue and it came from what I would
    > > > consider a reliable source. Seems like some heat shrink
   tubing will
    > > > do the trick and is much cleaner. I may just make some sort
   of mold
    > > > that I can squirt the silicone into that I can just slip it
   over the
    > > > tension bolt. Any ideas ?
    > > > maybe McMaster has something I can use.
    > > >
    > > > Tony
    > >
    > > O.K.  I think I've got it. I'll cover the tension bolt with
    > > silicone insert the bolt into a piece of thin wall alluminum
    > > tubing, then I'll insert the tension bolt into the engine, which
    > > now has a nice smooth outer alluminum finish. That should work
    > > and it will look good too even though I can't see it. They will
    > > pull out with no mess if I need to tear down the engine. I woke
    > > up at 3:00am this morning and wrote it down I had a dream about it.
    > > I need to get a life LOL :)
    > >
    > > Tony
    > >
    > > That is a pretty good idea Tony. Now the devil is in the details.
    > > Where do you get exactly the right ID/OD of tubing.
    > > Turning it on a lathe 18 inches long is not easy.
    > > --
    > >
    >
    > Paul
    > Why does it have to be one continuous piece? I'll bet I could put
   3 or 4 1in pieces along the tension bolt and that would do the trick
   as Aubrey said, it doesn't take a whole lot to get the job done.
    > So why not just make 1in aluminum spacers?  That might work. I
   think that Mcmaster has something that will be the right size. The
   only dim you really need is the I.D. of the holes in the castings. The
    > I.D. of the spacers can be filled with sillicone or reamed to the
   correct I.D. I'll bet Mcmaster has some unthreaded standoffs that
   will work great and they are pretty cheap as well. I'm at work but
    > if someone could get me the I.D. of the casting holes I'll look
   online at Mcmaster and see what I can find that will work.
    >
    > Tony
    >
    > Well I suspect the casting holes are not aligned bored
    > so they may vary in ID. I don't have any housings here
    > so somebody measure some holes. Adding a few lead or tungsten
    > spacers would break up the resonant frequency.
    > --
    > Paul Lamar ...No rotor no motor.


   Paul
   McMaster definitely has some tubing that will work. The telescoping
   hobby aluminum or brass as Aubrey suggested will probably be a
   really nice and cheap (not to mention light weight) way to go.
   The tension bolt is .375 or 3/8 so I.D. of the tubing should be
   around .400 maybe allow some room for silicone. I don't think the
   tubing actually has to touch the walls of the housing,Iron or
   aluminum. Of course now,you have to make sure that the concentrically
   is fairly good as you will be turning the entire assembly in the hole.
   OR maybe use a light coat of Vaseline on the tension bolt and when
   the silicone cures the bolt will simply turn isinde the whole
   assembly that's if the concentrically is to far off. Otherwise it
   may be like a cam of sorts. Follow Me on that????

   Tony

   Yes getting it to go in might be a REAL problem if it
   is NOT concentric.

   I think you would be better off just wrapping it with
   silicone tape.

   But let us know success or failure. We learn from mistakes
   as well as successes.
   --
   Paul Lamar ...No rotor no motor.



Okay, how about line boring the holes so that concentricity is very good?


Matt-

Of course that will work and it is what Guru racing does
along with larger bolts. Very expensive.

Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.