Subject: Combination slide throttle and carburator
From: Rotary Engine
Date: 11/9/2006, 5:29 PM
To: AA-me


            This is a VERY simple system. No computer, no sensors, no
            floats, no venturi, no fuel injectors, no nothing. Just very
            low pressure fuel. The fuel orifice area simply increases with
            the air passage area increase. Bigger fuel hole bigger air
   hole.
            There is another simple series valve that controls leaning.
            Paul Lamar

        Paul,
           FWIW I believe the Aero-Carb violates the Lectron patents, if
        they are
        still active. The Lectron I worked with used a square slide like a
        slide
        throttle, but were built on a single bore using a return spring
   and pull
        cable.
        Bill Jepson

        http://www.aeroconversions.com/carb_specs.html


        Times up.
        Here it is. Super simple. A series of progressively larger
        feed holes in the Teflon slide communicating a with a fixed
        larger fuel hole in the aluminum spacer.

        Patent applied for :)
        -- Paul Lamar ...No rotor no motor.

        Paul,
        Sorry for not getting back yesterday, went to bed. The hole
   idea is ok
        but you will have some problems. Kind of like a digital drive
   for an
        analog circuit? An alternate idea would be to have a single
   feed hole
        and a shallow tapered wedge connected to the feed on the end.
   easier to
        make too. (some of the holes would be reeeeeelly small) Tell me
   what you
        think.
        Bill Jepson

        Good idea Bill. Cheaper than my system. Less cost to make.
        Will work better. With an NC mill program you could vary the slope
        of the ramp.

        Paul Lamar ...No rotor no motor.

        Here is the $7 mixture control valve from Home Depot.

        This is a major break through in aircraft fuel systems.
        Simple systems like this work because the aircraft
        engine has simple requirements. The load is fixed
        and the RPM is constant. The only real reason for a complicated
        carb or EFI system is automatic mixture control.
        Since pilots are used to setting the mixture manually
        it makes no sense to have an automatic mixture control
        as well.

        With an EFI system you are in a world of hurt if your
        alternator fails. You have a limited amount of time
        before your EFI system stops as well as your engine.
        That is due to the high current requirements of high
        pressure fuel pumps. In this case you could use a hand
        pump to keep fuel supplied to a small sump tank mounted
        up under the cowl.

        The cost of this system everything included is less
        than about $200.  The cost of an EFI system everything
        included is well over a $1000.

        Not to mention the intrinsic high power of a slide throttle
        P-port engine.

        Klause Savier has run his O-200 with something similar as a back
        up to a Posa Carb.

        BTW the Wright brothers used something similar.

        Paul Lamar ...No rotor no motor.


   Hey Paul,

   I am not completely clear on how this works..  I can see that throttle
   position modulates fuel delivery, but does mass airflow also?  Do you
   need a venturi of sorts to control fuel flow while the slide is
   completely open?


   Regards,

   Matt-

   Nope. Constant dribble system.  You adjust the amount of dribble
   with the Home Depot 1/4 inch pipe ball valve. One advantage
   over most EFI systems is you can use two Home Depot valves
   and adjust the mixture on each rotor individually according
   to their EGTs.
   --
   Paul Lamar ...No rotor no motor.


And you predict that the throttle response will be adequate for aircraft
use?

I am guessing that if you have a fixed pitch prop, it will run very rich
at takeoff - low RPM doesn't move much air, and very lean while in a
part throttle descent - maybe not a problem on a rotary.  It might work
rather well on a rotary, given the seeming ability to run smoothly at
very lean mixture settings.  And that there aren't exhaust valves to cook.

Two-stroke aircraft engines usually have part-throttle descent overlean
problems - leading to seizures.  Nice to be able to ignore that.


Matt-

Sure. People use these kinds of carbs all the time in aircraft.
The Posa is very similar. Also my friends tell me a lot
of motorcycle carbs are built like this. The difference is
we don't have a needle to get in the way of the air flow at WOT.

How rich it runs at takeoff can be adjusted by the ramp
or by setting the mixture to best power at static RPM.
That is SOP at high altitude airports anyway. The engine normally
would be too rich at takeoff so you lean it to best power
at static RPM. (Max static RPM). At Big Bear here in SOCAL novices
are always crashing on take off from 7,000 foot Big Bear airport
because they don't do this. They make the mistake of taking off
full rich.

A p-port rotary will be rough no matter what you do on
the over run short of cutting off all fuel. This you
can do by pulling the leaning knob(s) with this set up.
-- 
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.