> This is a VERY simple system. No computer, no sensors, no
> floats, no venturi, no fuel injectors, no nothing. Just very
> low pressure fuel. The fuel orifice area simply increases with
> the air passage area increase. Bigger fuel hole bigger air hole.
> There is another simple series valve that controls leaning.
> Paul Lamar
>
> Paul,
> FWIW I believe the Aero-Carb violates the Lectron patents, if
they are
> still active. The Lectron I worked with used a square slide like
a slide
> throttle, but were built on a single bore using a return spring
and pull
> cable.
> Bill Jepson
>
>
http://www.aeroconversions.com/carb_specs.html
<http://www.aeroconversions.com/carb_specs.html>
>
>
> Times up.
> Here it is. Super simple. A series of progressively larger
> feed holes in the Teflon slide communicating a with a fixed
> larger fuel hole in the aluminum spacer.
>
> Patent applied for :)
> -- Paul Lamar ...No rotor no motor.
>
> Paul,
> Sorry for not getting back yesterday, went to bed. The hole idea
is ok
> but you will have some problems. Kind of like a digital drive for an
> analog circuit? An alternate idea would be to have a single feed hole
> and a shallow tapered wedge connected to the feed on the end.
easier to
> make too. (some of the holes would be reeeeeelly small) Tell me
what you
> think.
> Bill Jepson
>
> Good idea Bill. Cheaper than my system. Less cost to make.
> Will work better. With an NC mill program you could vary the slope
> of the ramp.
>
> Paul Lamar ...No rotor no motor.
>
> Here is the $7 mixture control valve from Home Depot.
>
> This is a major break through in aircraft fuel systems.
> Simple systems like this work because the aircraft
> engine has simple requirements. The load is fixed
> and the RPM is constant. The only real reason for a complicated
> carb or EFI system is automatic mixture control.
> Since pilots are used to setting the mixture manually
> it makes no sense to have an automatic mixture control
> as well.
>
> With an EFI system you are in a world of hurt if your
> alternator fails. You have a limited amount of time
> before your EFI system stops as well as your engine.
> That is due to the high current requirements of high
> pressure fuel pumps. In this case you could use a hand
> pump to keep fuel supplied to a small sump tank mounted
> up under the cowl.
>
> The cost of this system everything included is less
> than about $200. The cost of an EFI system everything
> included is well over a $1000.
>
> Not to mention the intrinsic high power of a slide throttle
> P-port engine.
>
> Klause Savier has run his O-200 with something similar as a back
> up to a Posa Carb.
>
> BTW the Wright brothers used something similar.
>
> Paul Lamar ...No rotor no motor.
I think it would be great as a redundant system (no offence). I
can't see it
running as efficiently as EFI but when it all goes to hell in a hand
basket
it sure would be nice and there is no real weight penalty to pay.
John
Why not as efficiently as EFI?
Paul Lamar
What would cause the fuel to vaporize instead of just dribbling in big
droplets? Surely even the rotary likes vaporized fuel..
Matt-
Well you look down the pipe of a p-port engine when
it is running and you see all sorts of dropletts.
If it were pure fuel vapor I don't think you would
see anything. Here is a movie on the subject.
http://www.mpsys.ca/
http://www.mpsys.ca/MPSv1.htm
Hard to say what it does at full power WOT.
You could always add heat and see what happens.
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.