>
>> Hi Bill,
>> I like the idea that the sliding block does not have the float valve
>> that worried you. If it worries you, then it worries me!
>> Does the Lectron have a float bowl?
>> Dave McC
>>
>> Dave,
>> The Lectron has a conventional float bowl. The unique part of
the carb
>> is that it uses a single, specially tapered central needle for
all fuel
>> distribution. (idle to WOT) This is why I believe Pauls idea about
>> the Slide Throttle carburetor could be made to work. The only
concern I
>> have for float systems is that they must be kept supplied with
fresh
>> CLEAN fuel. There are many good filters, and running one is
needed on a
>> carb system. You need to fly regularly to be sure the fuel
doesn't get
>> old and produce "gum" by having the light ends evaporate off.
>>
>> Bill Jepson
>>
>> This system is easy enough to check on the bench.
>> You set it up with a typical head of fuel and
>> use a calibrated beaker to measure the flow as a function
>> of slide position. Same thing goes for the leaning valve.
>>
>> One can always heat the slide plates to 200 F with
>> a hot air blower. I also have a vacuum pump that can
>> be used.
>> Paul Lamar
>
> The two strokers even have a small electric coil around the
> venturi for heat. I have seen them for sale on ebay.
> The mixture control on the Aerocarb is extremely simple,
> maybe even less than $7. It is a needle valve with the
> seat bored into the case at the inlet fitting. It can rotate
> through a quarter arc (90 degrees) with a lever attached
> to allow 2.5" of movement. My vernier mixture control
> makes very fine adjustments.
>
> Terry Adams
>
> The simplicity is stunning! Can be easily retrofitted
> to our current slide throttle design.
>
> Paul Lamar
>
Paul,
Wouldn't it make sense to create a venturi on one side of the slide
throttle
housing? The venturi part may be as simple as an add on 1/2 thick ring
that slips between the manifold and slide throttle. That way you
can use
the tapered central needle with its outlet emptying directly into the
airstream which IMHO is the essence of good fuel vaporization. A small
rectangular header tank could be put on top of the slide. Vapor lock
shouldn't be a problem with the tank close at hand. It could be
heated for
cold starts and the rely on engine heat for operations. Ethanol
ALWAYS needs
preheat on cold days. About 10 watts I am told.
One challenge would be how to create a linear cam that can depress both
spring loaded needle valves equally and be in sync with the throttle
linkage. More complication.
DougFir
Why? None of the other sliding block carbs have venturi's .
A bit of heat will vaporize the fuel no problem.
My guess is 150 F.
Venturi's have aerodynamic drag.
What needle's? We don't have needle's. No stinking needle's.
This is it. What you see is all you need.
Alcohol is your problem :)
Paul Lamar ...No rotor no motor.
The needle is replaced with a graduated slot. The other non-venturi
carbs don't have this feature.
The venturi provides enhanced vacuum signal vs. changes in airflow -
makes it easier to meter fuel based on airflow (for a conventional
carburetor). You get a vacuum signal just by blowing air past a slot.
That vacuum signal would be rather unstable depending on what the
airflow through the tube is like (level of turbulence).
How will this thing run when turbocharged?
What will keep the fuel in the intake runner instead of soaking the
whole slide throttle housing, and then dribbling out into the exhaust
system?
Does anything stop the fuel flow when the engine is turned off but the
throttle is open?
Don't get me wrong.. I'm not knocking this idea, just trying to think
through all of the operating details..
I think I like the idea of the slot.. How about stuffing the slot with
something the equivant of steel wool - to help the keep from forming
really big droplets?
Matt-
Won't work with a turbo charger. You need fuel
pressure to over come boost pressure. Boost pressure
varies over a wide range. EFI is the best solution
for a turbo engine for several other control reasons/needs.
From my experience and the MP systems video it is
guaranteed to soak the whole slide throttle. Here is a picture
of what we had to do to catch the fuel leaking out
of the slide throttle.
http://www.mpsys.ca/
That is why we went to all the trouble to seal the slide throttle
back around revision 2. However as far as the engine
is concerned it does not seem to matter or care.
If we heat the slide throttle to about 150 F the fuel between
the Teflon slide and the front and back plates
will vaporize and work its way into the engine as the engine
sucks.
You stop the fuel flow the same way you stop your
C182 engine. You pull on the lean knob. That shuts off
the one or two leaning valves. And fuel stops flowing
to the slide throttle. It does not matter where the
throttle is set.
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.