Subject: Combination slide throttle and carburetor
From: Rotary Engine
Date: 11/10/2006, 4:46 PM
To: AA-me


> > Hi Bill,
> > I like the idea that the sliding block does not have the float valve
> > that worried you. If it worries you, then it worries me!
> > Does the Lectron have a float bowl?
> > Dave McC
> >
> > Dave,
> > The Lectron has a conventional float bowl. The unique part of the
carb
> > is that it uses a single, specially tapered central needle for all
fuel
> > distribution. (idle to WOT) This is why I believe Pauls idea about
> > the Slide Throttle carburetor could be made to work. The only
concern I
> > have for float systems is that they must be kept supplied with fresh
> > CLEAN fuel. There are many good filters, and running one is needed
on a
> > carb system. You need to fly regularly to be sure the fuel doesn't
get
> > old and produce "gum" by having the light ends evaporate off.
> >
> > Bill Jepson
> >
> > This system is easy enough to check on the bench.
> > You set it up with a typical head of fuel and
> > use a calibrated beaker to measure the flow as a function
> > of slide position. Same thing goes for the leaning valve.
> >
> > One can always heat the slide plates to 200 F with
> > a hot air blower. I also have a vacuum pump that can
> > be used.
> > Paul Lamar
> > The two strokers even have a small electric coil around the
> venturi for heat. I have seen them for sale on ebay.
> The mixture control on the Aerocarb is extremely simple,
> maybe even less than $7. It is a needle valve with the
> seat bored into the case at the inlet fitting. It can rotate
> through a quarter arc (90 degrees) with a lever attached
> to allow 2.5" of movement. My vernier mixture control
> makes very fine adjustments.
> > Terry Adams
> > The simplicity is stunning! Can be easily retrofitted
> to our current slide throttle design.
> > Paul Lamar
> > The Rotary Engine NewsLetter. Powered by Linux.
> ACRE NL web site. http://www.rotaryeng.net <http://www.rotaryeng.net/>
> Copyright 1998-2006 All world wide rights reserved.

Folks,

Have been out of town so am not exactly sure how we got here but have to
say this is looking pretty ingenious.

One question I have is how well the fuel will atomize and evenly
distribute just dribbling into the side of the air flow. If there was a
long way between the slide and the intake port, this would be a mute
point but my understanding it that is should kept close.

Perhaps an internal tube to get the fuel closer to the center of the
flow stream or even another fuel entry point? Just a thought.....

Regardless, a very simple, robust system for our needs. Good job!

Steve Webre
Broussard, LA

We are going to try adding a little heat to cause
the fuel to vaporize. Some where around 150 F should work.

-- Paul Lamar ...No rotor no motor.

Paul,
Older street cars had this problem and several V8's ran the coolant
throught he manifold. Personally I am NOT that worried about
vaporization. I just think the injector does a better job of atomizing
the fuel. If absolutely necessary we could put a tiny vg in front of the
hole. 2 stroke carbs have a little half round pipe that sticks up about
1/8 inch in front of the needle jet to help with this. Point is it is a
solvable situation, IF it is even a problem in the first place. Proper
ramp and flow rates are FAR more important.
Bill Jepson


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.