Subject: Mechanical FI plumbing.
From: Rotary Engine
Date: 11/21/2006, 5:09 PM
To: AA-me



        Very very simple compared to EFI.
        --
        Paul Lamar ...No rotor no motor.



   Does sliding the throttle provide a valving effect on fuel flow?  You
   sent out a slightly more detailed depiction of the interface between
   the
   fuel line and the slide throttle, but it wasn't quite clear enough
   for me..

   Roughly what fuel pressure will be required to make this system work?
   If you assumed a 0.5" fuel line, roughly how much pressure is required
   to make 300hp, assuming the mixture valve is open (full rich)?  If that
   pressure is applied to this system, what keeps fuel from spurting out
   the top when the throttle is closed?


   Matt-

   Yes.

   The Teflon is a close fit inside the spacer. Any fuel
   getting past the sliding seal will flow to the bottom of the slide
   and out the slide drain back to the fuel tank unless it is
   a high wing airplane. Then, ironically, you will need another
   pump or let it drain over board. However if you close the
   throttle you will probably pull the lean knob which will cut
   off the fuel supply.

   2 to 3 psi has been quoted but it will probably work
   with gravity feed from a header tank according to Aerocarb.
   12 inches of fuel is .34 psi.

   Here is an Aerocarb plumbing diagram.

   Here is the equation.

   Q = AV

        Q = The flow in cubic feet per second (ft3/sec).

        A = The area of the orifice in square feet (ft2).

        V = The velocity of the liquid in feet per second (ft/sec).

         V = 8.02 times the square root of the head for water.

      .387 hole A = .1179 square inches or .0008189.
                V = 1 for a 12 inch head (water)

   Therefor Q = .0008189 cubic feet per second. 1728 cubic inch
   per cubic foot. 1.415 cubic inch per second. Fuel is 49 pounds per
   cubic foot or flow is equal to .04 pounds per second or 2.4
   pounds per minute or 144 pounds per hour or 24 gallons
   per hour or more than enough :) Whew!

   At .5 BSFC 144 pounds per hour is 288 HP so you might need
   a larger line than 3/8th for 300 HP or a low pressure pump.

   Check my arithmetic.

   The C182 has 3/8 fuel lines but the head is more like 3
   or four feet.

   Paul Lamar ...No rotor no motor.



Okay thanks Paul..  Have you read either of the following?

http://www.ellison-fluid-systems.com/manual/section1.htm#4

http://www.ellison-fluid-systems.com/article/notaposa/notaposa.htm

I find it interesting that Ben Ellison talks about a demand regulator,
"Fuel is admitted to this metering tube by a demand regulator designed
to maintain a slightly negative fuel pressure. "

Your system sounds much simpler...  More like the Aerocarb than the
Ellison..

I found this comment about the aerocarb, which I thought was
interesting:

"Mine was also easy to set, and works well. 25 hrs of run time
on it. The only interesting thing it does is run faster at idle
when the tank is full, versus when the tank is empty. which makes
sense since it would have different pressure at the carb. I just
set it at a happy medium. I also added a spring to pull the
throttle open if the cable should come loose. this also took
away the last little bit of stickiness that was left."

http://mylist.net/archives/corvaircraft/2003/002499.html

Paul, do you think the mixture in your system will be dependent
on fuel system pressure?  If not, why?


Matt-

No it will be but with a low pressure regulator that should take
care of it.

-- 
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.