Subject: Four rotor/T62 turbo compound engine.
From: Rotary Engine
Date: 11/25/2006, 9:05 PM
To: AA-me


         Here is a photo of how the Solar T-62
         turbine planetary is oiled. The ratio is 10:1 and it runs with
    a pitch
         line velocity around 12000 ft/min. The sun gear is not present, but
         you can see the three brass tubes that squirt oil on the gears
    just
         before they mesh.

         Aubrey

         --------------------------------------------

         Great picture Aubrey. Did you take it?
         Good analysis. I am surprised T62 APU operates at that pitch
         line velocity. I guess that is about right since it is rated at
         60,000 RPM and the pinion gear is tiny. Around 3/4 inch
         in diameter. Glorified turbo charger :)

         In the case of the T62, the dwg of which I attached, the
         shafts of the planet gears are fixed to the case so the
         pitch line velocity is indeed 12,000 FPM.
         The output shaft of the T62 rotates in the opposite
         direction to that of the turbine/compressor shaft.

         -----------------------------------------------
         Aubrey, your mention of the T62 gave me an idea.
         All we need do is marry a T62 without the burner
         cans to a suitable large rotary engine such as
         a three or four rotor and we have a cheap turbo compound
         engine of around 500 HP or so with a BSFC of below .40.
         Basically a T62 is a large turbo charger with gear box output.
         The 10:1 gear ratio is perfect for a turbo compound
         engine. I wish I had this idea before I spent
         $7,000 on a small turbo compound gear box.

         Do you know where I can download a dwg of the T62
         with dimensions? I am working on a 3D.

         I have a three rotor sitting in the hanger destined
         to become a turbo compound three rotor :)

         ------------------------------------------

         I think we lucked out. According to this picture
         the T62 turbine/compressor rotates clockwise. The gear box
         reverses that direction so looking at it from this
         perspective the output shaft rotates counter clock
         wise. Turning the T62 around 180 degrees and connecting
         the T62 output directly to the nose of the three
         rotor e-shaft will work perfectly. Perhaps with a
         flexible rubber coupling. Looking at the Mazda rotary
         from the front of the engine (car) it rotates clockwise.
         Perfect!

         For a tractor airplane there will be a S duct to route
         the exhaust down and under the firewall.

         This is a perfect low frontal area engine for a wing mounted
         twin as the exhaust can go straight back. All we need do now is
         fabricate the intake and exhaust plumbing to convert the T62
         back to a BIG turbo charger.

         -----------------------------------

         It will be about the same diameter, length and not far off
         the weight of a P&W PT6 with half the fuel burn. The
         T62 APU weighs about 70 pounds with the burner cans and
         the now unneeded starter and control box.

         Retrofitted to a Beech King Air it will have about twice
         the range.

         --
         Paul Lamar ...No rotor no motor.


         Paul,

         That's a great idea. You could get significant thrust from the
         exhaust jet if it was pointed straight back, maybe 25 percent of
         total thrust horsepower at altitude.

         The T-62 is rated at about 70 shaft horsepower. It seems to be
    about
         the right size as a recovery turbine and compressor for a
    3-rotor. I
         would think that 70 hp is just about what you could recover
    from the
         turbine wheel of a 3-rotor.

         Btw, there are two versions available with different reduction
         gearing. One was used on the CH-47 and has a lower output speed of
         6,000 rpm and turbine speed of 56,000 rpm.

         The other one was used on the CH-54 and has an output speed of
    8,000
         rpm and turbine speed of 56,700 rpm. It's also quite a bit shorter,
         as you can see from the specs.

         The hard part is going to be the exhaust and intake plumbing.
    Have a
         look at the airflow diagram. Both the intake and exhaust follow a
         convoluted course, because it is just a modified turbocharger, as
         you pointed out.

         You will have to modify that burner so the compressed air goes to
         the engine and not the turbine. At the same time you have to route
         the engine exhaust from the engine into the turbine wheel. It
         doesn't look easy -- both exhaust and compressed air are in close
         quarters there.


         Regards,

         Gordon.

    One correction. Unfortunately the T62 turns the wrong
    way. I have made this mistake before. It is going to need
    a small spur gear box to reverse rotation. I agree on the
    plumbing challenge. Fortunately I have a friend
    here at SZP that has a T62 that I can ply with.
    I will probably remove the entire burner can and
    see what is involved. More on this next week.
    --
    Paul Lamar ...No rotor no motor.



T62's are rated to 160hp+, and weigh about 190lbs (all up) I think..  I
think the one they are using the Helicycle is being run at (derated to)
90hp continuous and has been cut down to less than 140lbs (with a
different gearbox casting).

I suspect the 70lb weight is just the turbine - no gearbox.

A very entertaining idea anyway.


Matt-

Which model Matt? There is a larger model than the -16A which
you may be referring to. Dash 32 I think. The -16A weighs 70
pounds with everything: starter, control box, burner, tail pipe.

Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.