Subject: Four rotor/T62 turbo compound engine.
From: Rotary Engine
Date: 11/27/2006, 8:46 AM
To: AA-me



          Here is a photo of how the Solar T-62
          turbine planetary is oiled. The ratio is 10:1 and it runs with
     a pitch
          line velocity around 12000 ft/min. The sun gear is not present, but
          you can see the three brass tubes that squirt oil on the gears
     just
          before they mesh.

          Aubrey

          --------------------------------------------

          Great picture Aubrey. Did you take it?
          Good analysis. I am surprised T62 APU operates at that pitch
          line velocity. I guess that is about right since it is rated at
          60,000 RPM and the pinion gear is tiny. Around 3/4 inch
          in diameter. Glorified turbo charger :)

          In the case of the T62, the dwg of which I attached, the
          shafts of the planet gears are fixed to the case so the
          pitch line velocity is indeed 12,000 FPM.
          The output shaft of the T62 rotates in the opposite
          direction to that of the turbine/compressor shaft.

          -----------------------------------------------
          Aubrey, your mention of the T62 gave me an idea.
          All we need do is marry a T62 without the burner
          cans to a suitable large rotary engine such as
          a three or four rotor and we have a cheap turbo compound
          engine of around 500 HP or so with a BSFC of below .40.
          Basically a T62 is a large turbo charger with gear box output.
          The 10:1 gear ratio is perfect for a turbo compound
          engine. I wish I had this idea before I spent
          $7,000 on a small turbo compound gear box.

          Do you know where I can download a dwg of the T62
          with dimensions? I am working on a 3D.

          I have a three rotor sitting in the hanger destined
          to become a turbo compound three rotor :)

          ------------------------------------------

          I think we lucked out. According to this picture
          the T62 turbine/compressor rotates clockwise. The gear box
          reverses that direction so looking at it from this
          perspective the output shaft rotates counter clock
          wise. Turning the T62 around 180 degrees and connecting
          the T62 output directly to the nose of the three
          rotor e-shaft will work perfectly. Perhaps with a
          flexible rubber coupling. Looking at the Mazda rotary
          from the front of the engine (car) it rotates clockwise.
          Perfect!

          For a tractor airplane there will be a S duct to route
          the exhaust down and under the firewall.

          This is a perfect low frontal area engine for a wing mounted
          twin as the exhaust can go straight back. All we need do now is
          fabricate the intake and exhaust plumbing to convert the T62
          back to a BIG turbo charger.

          -----------------------------------

          It will be about the same diameter, length and not far off
          the weight of a P&W PT6 with half the fuel burn. The
          T62 APU weighs about 70 pounds with the burner cans and
          the now unneeded starter and control box.

          Retrofitted to a Beech King Air it will have about twice
          the range.

          --
          Paul Lamar ...No rotor no motor.


          Paul,

          That's a great idea. You could get significant thrust from the
          exhaust jet if it was pointed straight back, maybe 25 percent of
          total thrust horsepower at altitude.

          The T-62 is rated at about 70 shaft horsepower. It seems to be
     about
          the right size as a recovery turbine and compressor for a
     3-rotor. I
          would think that 70 hp is just about what you could recover
     from the
          turbine wheel of a 3-rotor.

          Btw, there are two versions available with different reduction
          gearing. One was used on the CH-47 and has a lower output speed of
          6,000 rpm and turbine speed of 56,000 rpm.

          The other one was used on the CH-54 and has an output speed of
     8,000
          rpm and turbine speed of 56,700 rpm. It's also quite a bit shorter,
          as you can see from the specs.

          The hard part is going to be the exhaust and intake plumbing.
     Have a
          look at the airflow diagram. Both the intake and exhaust follow a
          convoluted course, because it is just a modified turbocharger, as
          you pointed out.

          You will have to modify that burner so the compressed air goes to
          the engine and not the turbine. At the same time you have to route
          the engine exhaust from the engine into the turbine wheel. It
          doesn't look easy -- both exhaust and compressed air are in close
          quarters there.


          Regards,

          Gordon.

     One correction. Unfortunately the T62 turns the wrong
     way. I have made this mistake before. It is going to need
     a small spur gear box to reverse rotation. I agree on the
     plumbing challenge. Fortunately I have a friend
     here at SZP that has a T62 that I can play with.
      More on this next week.

     Paul Lamar ...No rotor no motor.

Here is a 3D for a three rotor version. I do not have
a good drawing with dimensions yet on the T62 so this is
approximate. The gearbox/accessory case could be redesigned
as much of it is not needed. Also the last half consisting
of the burner can will be removed.


Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.