Subject: Oil metering pump/ Mechanical fuel pump
From: Rotary Engine
Date: 12/1/2006, 4:08 PM
To: AA-me



> >>      paul
> >>
> >>      Do you see any reason why I can't use the shaft that turns
> >>      the oil metering pump to drive a mechanical fuel pump. What
> >>      I would like to do  is have a mechanical pump and an electric
> >>      boost pump. I'm thinking of using that Ellison 4-5 throttle body.
> >>      Now if I could just figure out how to run a mag on this thing.
> >>
> >>
> >>      Tony
> >>
> >>      Yes that should work.
> >>      Kinsler has mechanical fuel pumps.
> >>      http://www.kinsler.com/
> >>      --
> >>      Paul Lamar ...No rotor no motor.
> >>
> >> Paul and Tony,
> >>   I would avoid using the oil pump drive for a mechanical fuel pump.
> >> Unless you are talking about a low -pressure automotive (carb) pump. If
> >> it's a MFI pump it has higher HP requirements than I'd trust to the oil
> >> pump drive. The requirements for the oil pump are low due to the very
> >> small amount of oil it must move. Think about the volume, around 100X
> >> less than a fuel pump right?
> >> Bill Jepson
> >>
> >> It would be low pressure if it were for the Ellison.
> >> The drive shaft design is also over kill. But to be on the safe
> >> side drive it with a cog belt and then you can control
> >> the pump RPM, pressure and volume of fuel supplied
> >> by changing the pulley ratio.
> >>
> >> Paul Lamar ...No rotor no motor.
> >>
> >
> >
> > Bill an Paul
> >
> > But isn't fuel far less viscous than oil? why would it require more HP?
> > Plus! the oil metering pump pushes that oil into very small jets right?
> > Is it atomized to a degree or is it like a drip system?
> >
> > Tony
> >
> >
> > Paul,
> I would agree with Bill on the prohibition against using that metering
> pump drive to power a fuel pump.  Most low pressure mechanical fuel
> pumps are diaphragm types and the fuel pressure is produced by a spring
> acting on the diaphragm.  The mechanical drive for the pump is usually
> from a cam that "resets" the spring against the fuel pressure.  The
> torque load, therefore, would be strongly pulsating.  The oil metering
> pump on the other hand, is a tiny variable displacement vane pump that
> operates against essentially zero pressure (because it is a dribble system).
> > Aubrey
> > I don't think that is the kind he is talking about.
>   The aircraft style
> boost pump has vane's that slip in and out of a slotted
> rotating drum for lack of a better description.
> > The Kinsler pump is like that as well.
> > The drive design is way over kill for the metering pump.
> -- > Paul Lamar ...No rotor no motor.

Paul

I have seen several rotating FI pumps. What I don't know is,
what  the operating RPM is for those pumps. The pumps I've seen
on the net are usually bolted to the front of a small block in a
drag racing application or some derivitive thereof. If I'm not
mistaking the drive is 2:1 is that right? if so it will produce
3000rpm is that enough for a FI pump to supply adequate pressure?
I have to say after looking at that gear drive it is way over built .
I doubt our problem would lie in the gear drive maybe the ratio is wrong,
if it is to much we can simply regulate that correct? I'll make the bracket
to mate it up to the motor I'll copy the oil metering pump shaft to make a
couplink to mate the two shafts together. I'll draw them in Rhino and see
what you think. Let me know about that RPM issue though, If it isn't enough
than there is no point in wasting time with it.

Tony

Contact the man. and see what the pump flow is as a function of
RPM and gear it down.

-- 
Paul Lamar ...No rotor no motor.


Paul,

I did just that.The pumps run  anywhere between 2000 and 3000
RPM's. they can gear them to make any preasure to run any
system you want very good news.

Tony



The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.